9
PROGRAMMING PHONE NUMBERS AND FORMATS
(REQUIRED PROGRAMMING FOR CENTRAL STATION REPORTING)
This section describes all the locations that must be programmed for the Ranger 8600E to
function and report to a central station. Other programming can be found in the section
“Programming Instructions” starting on page 10.
LOCATIONS 032-047: PROGRAMMING THE PRIMARY TELEPHONE NUMBER
Theprimarytelephone number is programmedin successive locations beginningwith location 032. Anyzero(0) within
the telephone number, must be programmed as a "10". A "0" indicates the end of the phone number. Delays of four
seconds can be programmed at any point in the phone number by programming a "13" in the appropriate location. If
tone dialing is desired, program a "15" in the location where tone dialing should begin. If the entire number should be
tone dialing, program a "15" in location 032. Program an "11" for a "DQGDIRUD:KHQXVLQJVSOLWUHSRUWLQJ
the primary number always takes priority over the secondary telephone number.
LOCATIONS 048-051: PROGRAMMING THE ACCOUNT CODE FOR THE PRIMARY PHONE NUMBER
The account code sent when the PRIMARY phone number is dialed is programmed in locations 048-051. Any zero (0)
withinthe account codemustbe programmedas a"10",and thecommunicator willreporta zero(0). Iftheaccount code
isthree digits long,use locations048, 049, and050, andprograma "0"in location051to indicatethe endofthe account
code.
LOCATION 052: PROGRAMMING COMMUNICATOR FORMAT FOR THE PRIMARY PHONE NUMBER
Location 052 contains the communicator format used to transmit to the receiver connected to the primary phone
number. Consult the instructions for your central station receiver to determine which format is compatible. To select
Ademco/Silent Knight Fast, program a "2" in location 052. Radionics 1800HZ/2300HZ Fast w/Parity and Hex
Capabilityrequires a "9" in thislocation. For a Pager format,program a"15"in this location,along with theappropriate
data in locations 208 and 209. If you need another format, choose from those listed in the format table located on the
following page, and program the data in location 052. If this location contains a "0", the built-in communicator will be
disabled, and the Ranger 8600E will function as a local only control.
LOCATION 053: DISABLING THE SECONDARY TELEPHONE NUMBER AS A BACKUP
Location 053 is used to disable the secondary phone number as a "backup". This feature can be used with split
reporting (locations 176-177) to prevent a report from going to the secondary telephone number after unsuccessful
attemptsto theprimaryphone number. Programminga "0"will make thesecondary phonenumber backuptheprimary,
and the primary phone number backup the secondary. Programming a "3" will make the control alternate from the
primary to the secondary number (2 calls each) for the number of attempts programmed in location 134. If location 053
contains a "1", only the primary phone number will be called.
LOCATIONS 054-069: PROGRAMMING THE SECONDARY TELEPHONE NUMBER
Locations054-069 contain thesecondary telephonenumber. This numberallows certaincommunicatorreports togo to
another number, or to cause the communicator to dial a second number if the primary number does not respond after
the number of attempts programmed in location 134 have been tried unsuccessfully. The same number of attempts is
made with the back-up number. Tone dialing and delay instructions are the same as for the primary number.
LOCATIONS 070-073: PROGRAMMING THE ACCOUNT CODE FOR THE SECONDARY PHONE NUMBER
Locations 070-073 contain the account code for the secondary phone number. Any zero (0) within the account code
mustbe programmed asa "10", andthe communicatorwillreport azero (0). If theaccount codeisthree digitslong, use
locations070, 071, and072, and programa "0"inlocation 073to indicate theend oftheaccount code.If these locations
are left blank, the account code in locations 048-051 will be reported.
LOCATION 074: PROGRAMMING COMMUNICATOR FORMAT FOR THE SECONDARY TELEPHONE NUMBER
Location 074 contains the communicator format for the secondary phone number. Consult the instructions for your
central station receiver to determine which format is compatible. To select Ademco/Silent Knight Fast, program a "2"
in this location. Radionics 1800HZ/2300HZ Fast with Parityand Hex Capabilityrequiresa "9" inthislocation. For a
Pager format, program a "15" in this location, along with the appropriate data in locations 208 and 209. If you need
another format, choose from those listed in the following Table 1.1, and program the appropriate data in this location. If
location 074 is "0", the format programmed in location 052 will be used.
