Calculated Industries Construction Master 5 Bedienungsanleitung

The

Construction Master 5

calculator helps

you save time, cut costly errors and build

like a pro!

Quickly Solve:

• Feet-Inches-Fractions, Yards, Metric

Dimensional Problems and Conversions

• Problems Involving All Fractions

— 1/2-1/64ths!

• Areas, Volumes and Weights

• Circle/Arc Calculations

• Common, Hip/Valley, Jack Rafter

Lengths (Regular and Irregular)

• Rake-Wall Solutions

• Concrete, Flooring Quantity

• Roofing Materials

• Squaring-Up

• Stair Layout Solutions, and more!

CONSTRUCTION MASTER®5 v3.1

GETTING STARTED...............................1

KEY DEFINITIONS/FUNCTIONS..........1

Basic Function Keys............................1

Dimension Keys...................................2

Arc/Circle Keys....................................4

Right Triangle/Roof Framing Keys ......4

Stair Layout Key..................................7

Stair Settings.......................................8

Miscellaneous Functions.....................8

PAPERLESS TAPE EXAMPLE ...........10

PREFERENCE SETTINGS .................11

ENTERING DIMENSIONS..................13

Linear Dimensions.............................13

Square and Cubic Dimensions..........13

Linear Conversions............................14

Square and Cubic Conversions.........15

BASIC MATH OPERATIONS ..............15

EXAMPLES...........................................16

Adding and Subtracting Strings of

Dimensions.....................................16

Multiplying Dimensions......................16

Dividing Dimensions..........................17

Percent Calculations..........................17

Square Area.......................................18

Rectangular Area and Volume...........18

Entering Square and Cubic and

Adding a Waste Allowance.............19

Weight Conversions ..........................19

Weight per Volume............................20

Using the Memory .............................21

Board Feet and Cost.........................22

Carpentry —

Calculating Number

of Studs

..........................................22

Baluster Spacing ...............................23

TABLE OF CONTENTS

Circle Area and Circumference .........24

Arc Angle or Degree..........................24

Concrete Volume for Driveway..........25

Concrete Columns.............................25

Complex Concrete Volume................26

RIGHT ANGLE/FRAMING...................28

Squaring-Up a Foundation ................29

Pitch —

Converting Roof Angle

.........29

Converting Slope...............................30

Common Rafter Length.....................30

Regular Hip/Valley and Jack

Rafters............................................31

Irregular Hip/Valley ............................33

Rake-Wall —

No Base

.......................34

STAIRS................................................35

Stairs —

Given Rise and Run

...........35

Stairs —

Given Only the Floor-to-Floor

Rise; Entering Other Than 7-1/2 Inch

Desired Riser Height

......................37

APPENDIX ............................................38

Setting Fractional Resolution.............38

Default Settings.................................39

Auto-Shut Off.....................................39

Accuracy/Errors.................................40

Battery ...............................................41

Replacing the Battery........................41

Reset .................................................41

AREAAND VOLUME FORMULAS .....42

REPAIR AND RETURN.......................44

WARRANTY ........................................45

FCC CLASS B.....................................47

LOOKING FOR NEW IDEAS..............47

POCKET REFERENCE GUIDE — 1

KEY DEFINITIONS/FUNCTIONS

Basic Function Keys

+ – x Arithmetic operation keys.

÷ =

0– 9Keys used for entering

and •numbers.

Percent Key

— Four-func-

tion (+, –, x, ÷) percent key.

Off Key

— Turns all power

off, clearing all non-perma-

nent registers.

On/Clear Key

— Turns on

power. Pressing once clears

the display. Pressing twice

clears all temporary values.

Convert Key

— Used with

the dimensional keys to

convert between dimen-

sions or with other keys to

access special functions.

√

Square Root Key

— Used to

find the Square Root of a

non-dimensional or area

value.

Ç √

x2Function

— Finds the

Square of a linear or non-

dimensional value.

GETTING STARTED

POCKET REFERENCE GUIDE — 2

Recall Key

— Used with

other keys to

recall

stored

values and settings.

Memory Key

— Adds the

displayed value to Memory.

Clears when the calculator

is shut off.

Ç µ

Memory Minus (M–)

—

Subtracts the displayed

value from Memory.

Ç ®

Memory Clear

— Clears

Memory without changing

current display.

® ®

Memory Clear

— Clears

Memory and displays

Memory Total.

Dimension Keys

Yards Key

— Enters or

converts to

Yards

Feet Key

— Enters or con-

verts to

Feet

as whole or

decimal numbers. Also

used with the iand /

keys for entering Feet-Inch

values (e.g., 6 f 9 i

1 / 2). Repeated press-

es during conversions tog-

gle between Fractional and

Decimal Feet.

POCKET REFERENCE GUIDE — 3

Inch Key

— Enters or con-

verts to

Inches

. Entry can

be whole or decimal num-

bers. Also used with the /

key for entering fractional

inch values (e.g., 9 i 1

/ 2). Repeated presses

during conversions toggle

between Fractional and

Decimal Inches.

Fraction Bar Key

— Used

to enter

Fractions

. Fractions

can be entered as proper

(1/2, 1/8, 1/16) or improper

(3/2, 9/8). If the denomina-

tor (bottom) is not entered,

the calculator's fractional

accuracy setting is auto-

matically used.

Meters Key

— Enters or

converts to

Meters

Centimeters Key

— Enters

or converts to

Centimeters

Millimeters Key

— Enters

or converts to

Millimeters

Board Feet Key

— Enters

or converts Cubic values to

Board Feet. One Board

Foot is equal to 144 Cubic

Inches.

POCKET REFERENCE GUIDE — 4

Weight Key

— Enters or

converts (a volume value)

Tons, Pounds, Metric

Tons

Kilograms

Repeated presses will cycle

through these units.

Arc/Circle Keys

Circle Key

— Calculates

Circle Area and

Circumference based on

entered Diameter.

Ç C

Arc

— Calculates Arc

Length or Degree based on

entered Diameter and Arc

Degree or Length (e.g., if

Arc Degree is entered, it

will calculate Arc Length,

and vice versa).

Right Triangle/Roof Framing Keys

Pitch Key

— This key is

used to enter or calculate

the Pitch (Slope) of a roof

(or Right Triangle). Pitch is

the amount of “Rise” over

12 Inches of “Run.” Pitch

may be entered as:

POCKET REFERENCE GUIDE — 5

a Dimension 9 i p

an Angle 3 0 p

a Ratio 0 • 7 5 Ç p

a Percentage 7 5 % p

APitch entry will remain in

permanent storage until

revised or reset. A solution

will be replaced by its

entered value once the

calculator is cleared.

Ç p Enters Pitch Ratio (e.g., •

5 8 3 Ç p).

Rise Key

— Enters or cal-

culates the Rise or vertical

leg (height) of a Right

Triangle.

Run Key

— Enters or cal-

culates the Run or horizon-

tal leg (base) of a Right

Triangle.

Diagonal Key

— Enters or

calculates the common or

Diagonal leg (Hypotenuse)

of a Right Triangle. Typical

applications are “squaring”

slabs or finding common

rafter lengths.

Hip/Valley Key

—

Calculates length of the

Regular or Irregular Hip/

Valley rafter.

POCKET REFERENCE GUIDE — 6

Ç H

Irregular Pitch

— Enters

Irregular

Pitch used to cal-

culate lengths of the

Irregular Hip/Valley and

Jack rafters.

Jack Key

— Calculates

Jack rafter lengths on the

Regular

-pitched roof side.

Ç j

Irregular Jack

— Calculates

Jack rafter lengths on the

Irregular

-pitched roof side.

∑

Rake-Wall Key

— Finds

the stud sizes based on

entered Right Triangle val-

ues and the stored On-

Center spacing. If a dimen-

sional value is entered

before pressing ∑, that

value is considered the

base and will be added to

the stud lengths.

Andere Handbücher für Construction Master 5

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Calculated Industries Kalkulator Handbücher

Calculated Industries

Calculated Industries Tradesman Calc 4400 Bedienungsanleitung

Calculated Industries

Calculated Industries PIPE TRADES PRO 4095 Bedienungsanleitung

Calculated Industries

Calculated Industries 9430 Bedienungsanleitung

Calculated Industries

Calculated Industries KitchenCalc Pro Bedienungsanleitung

Calculated Industries

Calculated Industries Sheet Metal/HVAC Pro Calc Bedienungsanleitung

Calculated Industries

Calculated Industries Frame Master II Bedienungsanleitung

Calculated Industries

Calculated Industries Qualifier Plus IIcx Bedienungsanleitung

Calculated Industries

Calculated Industries MACHINIST CALC PRO Bedienungsanleitung

Calculated Industries

Calculated Industries 3423 Bedienungsanleitung

Calculated Industries

Calculated Industries SCALE MASTER CLASSIC 6020 Bedienungsanleitung

Calculated Industries

Calculated Industries 4065 Construction Master Pro v3.0 Bedienungsanleitung

Calculated Industries

Calculated Industries Quilter's FabriCalc 8400 Bedienungsanleitung

Calculated Industries

Calculated Industries ElectriCalc Pro Bedienungsanleitung

Calculated Industries

Calculated Industries NautiCalc Plus Bedienungsanleitung

Calculated Industries

Calculated Industries 4225 Bedienungsanleitung

Calculated Industries

Calculated Industries 8515 Bedienungsanleitung

Calculated Industries

Calculated Industries 8015 Bedienungsanleitung

Calculated Industries

Calculated Industries 4065 Construction Master Pro v3.0 Bedienungsanleitung

Calculated Industries

Calculated Industries 8525 Bedienungsanleitung

Calculated Industries

Calculated Industries 8305 KitchenCalc Pro Bedienungsanleitung

Calculated Industries

Calculated Industries Construction Master III Bedienungsanleitung

Calculated Industries

Calculated Industries Measure Master Pro 4020 Bedienungsanleitung

Calculated Industries

Calculated Industries Machinist Calc 4086 Bedienungsanleitung

Calculated Industries

Calculated Industries 43285 Bedienungsanleitung

Beliebte Kalkulator Handbücher anderer Marken

HP 35s Handbuch

Casio

Casio CFX-9970G Bedienungsanleitung

LEXIBOOK

LEXIBOOK EL350 Bedienungsanleitung

HP HP-97 Bedienungsanleitung

Citizen

Citizen SDC-414N Bedienungsanleitung

Casio

Casio fx-3800P Bedienungsanleitung

Canon

Canon P26-DHIII Bedienungsanleitung

Citizen

Citizen 520DPA Bedienungsanleitung

Sharp

Sharp EL-9900 Bedienungsanleitung

Casio

Casio FX-9860GII - SOFTWARE VERSION 2-00 Bedienungsanleitung

Casio

Casio MS-7UC Bedienungsanleitung

Sharp

Sharp WriteView EL-W506 Technisches Handbuch

Casio

Casio FC-200 Bedienungsanleitung

Casio

Casio fx-CG50 Bedienungsanleitung

HP HP-67 Benutzerhandbuch

Royal

Royal CBC2000 Bedienungsanleitung

Heathkit

Heathkit IC-2009 Bedienungsanleitung

Universal

Universal UNV-15907 Bedienungsanleitung