Calculated Industries Home ProjectCalc Bedienungsanleitung

TABLE OF CONTENTS

Key Definitions ................................1

Basic Function Keys..................................1

Dimensional Unit Keys..............................2

Convert Key Functions ..............................3

Memory ....................................................4

Entering Square or Cubic..........................4

Fraction Resolution ..................................5

Project Keys..............................................5

Basic Dimensional Math ....................7

Linear Conversions ..................................7

Square and Cubic Conversions ................8

Basic Dimensional Math ..........................9

Project Examples-Using Default Values..10

Paint: Gallons, Quarts, or Pints of ..........10

Wallpaper: Rolls of..................................10

Tiles: Number of ....................................11

Carpet: Length of ....................................12

Concrete: Bags of ..................................12

Finding the Cost of Materials ..............13

Auto Shut-Off and Batteries ................14

Repair and Return ..........................15

Warranty ......................................16

OCKET

EFERENCE

UIDE

- 1

Basic Function Keys

o- On/Clear Key

Turns power on. Pressing once clears

the display. Pressing twice clears all

temporary values.

O- Off

Turns all power off, clearing all non-

permanent registers.

+ – x ÷ =

Arithmetic operation keys.

0- 9and

•

Digits used for keying in numbers.

%- Percent

(%)

Four-function (+, -, x, ÷) percent

KEY DEFINITIONS

Dimensional Unit Keys

y- Yards Key

Enters or converts to Yards.

f- Feet Key

Enters or converts to Feet as whole

or decimal numbers. Also used with

the i and /keys for entering

Feet-Inch-Fraction values (e.g., 6

f 9 i 1 / 2 ). Repeated

presses during conversions toggle

between Feet-Inch-Fractions and

Decimal Feet.

i- Inch Key

Enters or converts to Inches. Entry

can be whole or decimal number.

Also used with the /key for entering

Fractional Inch values (e.g., 9i

1 / 2 ). Repeated presses during

conversions toggle between

Fractional and Decimal Inches.

/- Fraction Bar Key

Used to enter fractions. Fractions

can be entered as proper (1/2, 1/8,

1/16) or improper (3/2, 9/8).

m- Meter Key

Enters or converts to Meters.

OCKET

EFERENCE

UIDE

- 2

Memory

Ç +

(M+)

- Adds or stores a value

in the semi-permanent memory (e.g.,

1 5 0 Ç +). Semi-permanent

means the value is cleared when the

calculator is turned off.

Ç – Ç +

(M-)

- Subtracts a

value from the semi-permanent

Memory (e.g., 1 5 0 Ç – Ç

+subtracts 150 from the memory).

Ç =

(MR)

- Recalls Memory value

(e.g., if 150 has been stored in Memory,

pressing Ç = will display 150).

Ç o

(MC)

- Clears Memory value.

Entering Square or Cubic

To label a dimension as “Square” or

“Cubic,” enter the value, then press the

desired dimension key twice for

Square and three times for Cubic. For

example, to enter 25 Cubic Yards,

press 2 5 y y y.

OCKET

EFERENCE

UIDE

- 4

OCKET

EFERENCE

UIDE

- 5

Fraction Resolution

Your calculator is set to display Fractional

values to the nearest 16th of an Inch

(default setting). Press Ç / to access

the fraction resolution setting. Repeated

presses of /will then revolve through

the available settings: 1/16, 1/32, 1/64,

1/2, 1/4 and 1/8. Press oto exit.

Project Keys

p- Paint

Calculates volume of paint, based on

an entered or calculated area. Finds

quantity in Gallons, Quarts or Pints

upon repeated presses.

w- Wallpaper

Calculates number of rolls of wallpaper,

based on an entered or calculated

area.

(Cont’d)

t - Tile

Finds the number of tiles, based on

an entered or calculated area.

Repeated presses will scroll between

numbers of tiles for various “stan-

dard” tile sizes (18”, 16”, 13”, 12”,

10”, 8”, 6”, 4”, 2”, 1” and 24”).

Note: Tile sizes shown in Inches, not Square

Inches. In other words, a 6” tile is really 6” x 6”,

or a 36 Square-Inch tile, but it is labeled as a 6”

size.

c- Carpet

Calculates carpet length required,

based on entered or calculated area.

Repeated presses of cwill scroll

between values for 12’, 13’, and 15’

rolls.

C- Concrete

Calculates the number of bags of

concrete required, based on an

entered or calculated volume (e.g.,

cubic feet or cubic yards).

Ç • - Cost

“Cost” function that allows you to

calculate total material cost.

OCKET

EFERENCE

UIDE

- 6

OCKET

EFERENCE

UIDE

- 7

Linear Conversions

Convert 15 Feet 9-1/16 Inches to other

units of measure.

KEYSTROKE DISPLAY

o0.

1 5 f 9 i 1 / 1 6

15 FEET 9-1/16 INCH

Ç f 15.75521 FEET

Ç i 189.0625 INCH

Ç y 5.251736 YD

Ç m 4.802187 M

Convert Decimal Inches to Fractional

Inches.

KEYSTROKE DISPLAY

o0.

1 4 • 7 9 3 i 14.793 INCH

Ç i 14-13/16 INCH

BASIC DIMENSIONAL MATH

OCKET

EFERENCE

UIDE

- 8

Square and Cubic Conversions

Convert 25 Square Feet to other

Square dimensions.

KEYSTROKE DISPLAY

o0.

2 5 f f 25. SQ FEET

Ç y 2.777778 SQ YD

Ç m 2.322576 SQ M

Convert 25 Cubic Feet to Cubic Yards.

KEYSTROKE DISPLAY

o0.

2 5 f f f 25. CU FEET

Ç y 0.925926 CU YD

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Calculated Industries Kalkulator Handbücher

Calculated Industries

Calculated Industries 3430 Bedienungsanleitung

Calculated Industries

Calculated Industries Time Master II Bedienungsanleitung

Calculated Industries

Calculated Industries 4065 Construction Master Pro v3.0 Bedienungsanleitung

Calculated Industries

Calculated Industries 3420 Bedienungsanleitung

Calculated Industries

Calculated Industries Qualifier Plus IIcx Bedienungsanleitung

Calculated Industries

Calculated Industries Machinist Calc 4086 Bedienungsanleitung

Calculated Industries

Calculated Industries Construction Master 5 Bedienungsanleitung

Calculated Industries

Calculated Industries 5065 Bedienungsanleitung

Calculated Industries

Calculated Industries PROJECTCALC Bedienungsanleitung

Calculated Industries

Calculated Industries Construction Master 5 Bedienungsanleitung

Calculated Industries

Calculated Industries ULTRA MEASURE MASTER 8020 Bedienungsanleitung

Calculated Industries

Calculated Industries Kitchen Calc PRO Master Chef's Edition 8305 Bedienungsanleitung

Calculated Industries

Calculated Industries 3423 Bedienungsanleitung

Calculated Industries

Calculated Industries 4030 Bedienungsanleitung

Calculated Industries

Calculated Industries Construction Master 5 4050 Bedienungsanleitung

Calculated Industries

Calculated Industries KitchenCalc Pro Bedienungsanleitung

Calculated Industries

Calculated Industries 9130 Bedienungsanleitung

Calculated Industries

Calculated Industries ElectriCalc Pro Bedienungsanleitung

Calculated Industries

Calculated Industries 4088 Bedienungsanleitung

Calculated Industries

Calculated Industries Quilter's FabriCalc 8400 Bedienungsanleitung

Calculated Industries

Calculated Industries KitchenCalc 8300 Bedienungsanleitung

Calculated Industries

Calculated Industries 6260 Bedienungsanleitung

Calculated Industries

Calculated Industries Ultra Scale Master 6250 Bedienungsanleitung

Calculated Industries

Calculated Industries Sheet Metal/HVAC Pro Calc Bedienungsanleitung

Beliebte Kalkulator Handbücher anderer Marken

HP 35s Handbuch

Casio

Casio CFX-9970G Bedienungsanleitung

LEXIBOOK

LEXIBOOK EL350 Bedienungsanleitung

HP HP-97 Bedienungsanleitung

Citizen

Citizen SDC-414N Bedienungsanleitung

Casio

Casio fx-3800P Bedienungsanleitung

Canon

Canon P26-DHIII Bedienungsanleitung

Citizen

Citizen 520DPA Bedienungsanleitung

Sharp

Sharp EL-9900 Bedienungsanleitung

Casio

Casio FX-9860GII - SOFTWARE VERSION 2-00 Bedienungsanleitung

Casio

Casio MS-7UC Bedienungsanleitung

Sharp

Sharp WriteView EL-W506 Technisches Handbuch

Casio

Casio FC-200 Bedienungsanleitung

Casio

Casio fx-CG50 Bedienungsanleitung

HP HP-67 Benutzerhandbuch

Royal

Royal CBC2000 Bedienungsanleitung

Heathkit

Heathkit IC-2009 Bedienungsanleitung

Universal

Universal UNV-15907 Bedienungsanleitung