CAME ZE5 Bedienungsanleitung

CONTROL PANEL

FOR EMEGA SERIES

lish

Installation manual

ZE5

319T92EN

The data and information reported in this installation manual are susceptible to change at any time and without obligation to notify users.

Pag.

2- Manual code:

319T92

319T92 ver.

2.0

2.0 11/2012 © CAME cancelli automatici s.p.a.

Legend

This symbol indicates sections to be read with

particular care.

⚠This symbol indicates sections concerning safety.

☞This symbol indicates notes to communicate to

users.

Description

Engineered and built entirely by Came Cancelli Automatici

S.p.A.

The control panel is powered by 230 v AC on terminals L

and N with max frequency of 50/60 Hz.

The command devices and accessories are powered by 24

Warning!The accessories must not exceed 20 W overall.

All connections are protected by quick fuses, see table.

he card provides and controls the following functions:

- automatic closing after an opening command;

- maintained action command.

The available command modes are:

- opening/closing;

- total stop.

The photocells, after detecting an obstacle, may trigger:

- the reopening of the closing gate;

- a total stop.

Special trimmers regulate:

- the time for automatic closing activation;

- the sensitivity for obstacle detection, during movement:

min/max;

- the automatic safety’s intervention time: min/max.

You can also connect:

- gate open warning-lamp o, in alternative, an electric lock;

- courtesy -lamp lighting the parking area for opening/

closing cycle.

Destination

The ZE5 electrical panel is designed to control EMEGA

(E306-E456) automation units in the movement of garage-

type doors with double or single motor.

The use of this product for purposes other than as

described above and installation executed in a manner

other than as instructed in this technical manual are

prohibited.

Limits of Use

The overall power of the motors must not exceed 300 W

400 W.

#!-%

MM MM

MM

Pag.

3- Manual code:

319T92

319T92 ver.

2.0

2.0 11/2012 © CAME cancelli automatici s.p.a.

The data and information reported in this installation manual are susceptible to change at any time and without obligation to notify users.

Technical data Dimensions

FUSE TABLE

to protect: fuses for:

Electronic board (line) 5 A

Command devices 630 mA

Accessories 1.6 A

TECHNICAL DATA

Power supply

230 V - 50/60 Hz

Maximum allowed power load 400 W

Power draw when idle 150 mA

Maximum power rating for 24V

accessories

40 W

Circuit insulation class

Container material ABS

Degree of protection IP54

Working temperature -20 / +55 °C

••

L N

V W

U E1 E3

1234

5678910

10 11 1 2 3 5 7 C1 FA

24 12 0

+ E -

- AMP. S+

- A.C.T.+

- S. DELAY +

L1T L2T

••••••

••• •

•

•• •

•• •• ••

••

••••

•

••• •

•

••••••••••••••••••••••••••

••••••••••••••••••••••••

•••••••

••

••••••••

••••

•••••••

•••••

•••• •

•

The data and information reported in this installation manual are susceptible to change at any time and without obligation to notify users.

Pag.

4- Manual code:

319T92

319T92 ver.

2.0

2.0 11/2012 © CAME cancelli automatici s.p.a.

1 630 mA board fuse

2 1.6 A fuse for accessories

3 Dip-Switch for function selector

4 Keys for radio code memorisation and for end-stop

programming

5 LED indicator

6 Trimmer for adjusting automatic closing times

7 Encoder sensitivity adjustment trimmer

8 Trimmer for adjusting operation times

9 Radiofrequency board coupling

10 5 A line fuse

11 Encoder connection terminal board

12 Aerial connection terminal board

13 Connection terminal board

14 Power feed terminal board

Main Components

Pag.

5- Manual code:

319T92

319T92 ver.

2.0

2.0 11/2012 © CAME cancelli automatici s.p.a.

The data and information reported in this installation manual are susceptible to change at any time and without obligation to notify users.

Installation

Preliminary checks

⚠Before proceeding with the installation, it is necessary

to:

• Make sure that the point where the electrical panel is

anchored is free from any impacts, and that the surface

is solid and that proper tools and materials are used (i.e.

screws, wall plugs, etc.).

• Set up a suitable omnipolar cut-off device, with distances

greater than 3 mm between contacts, with sectioned

power source.

• Check that any connections inside the container

(made for continuity purposes of the protective circuit)

are fitted with extra insulation compared to other internal

conductive parts.

• Set up proper conduits and electric cable raceways,

making sure these are protected from any mechanical

damage.

Equipment and materials

Make sure all the necessary tools and materials are avai-

lable to carry out the installation with the maximum safe-

ty, in compliance with regulations in force. Here are some

examples:

The data and information reported in this installation manual are susceptible to change at any time and without obligation to notify users.

Pag.

6- Manual code:

319T92

319T92 ver.

2.0

2.0 11/2012 © CAME cancelli automatici s.p.a.

Minimum thicknesses and cables types

N.B.: If the cable length differs from that specified in the table, then you must determine the proper cable diameter based

on the actual power draw from the connected devices and according to the CEI EN 60204-1 standards.

For connections that require several, sequential loads, the sizes given on the table must be re-evaluated based on actual

power draw and distances.

When connecting products that are not specified in this manual, please follow the documentation provided with said

products.

Connections Cable Type Cable Length

1 < 10 m Cable Length

10 < 20 m Cable Length

20 < 30 m

230V 2F power supply

FROR CEI

20-22

CEI EN

50267-2-1

3G 1,5mm² 3G 2,5mm² 3G 4mm²

230V 2F motors 4G 1mm² 4G 1,5mm² 4G 2,5mm²

230V ﬂashing lamp 2 x 0,5mm² 2 x 1mm² 2 x 1,5mm²

230V cycle / courtesy lamps 3G 0,5mm² 3G 1mm² 3G 1,5mm²

Power for 24V accessories 2 x 0,5mm² 2 x 0,5mm² 2 x 1mm²

24V pilot lamp 2 x 0,5mm² 2 x 0,5mm² 2 x 1mm²

Safety contacts 2 x 0,5mm² 2 x 0,5mm² 2 x 0,5mm²

N.O./N.C. command keys 2 x 0,5mm² 2 x 0,5mm² 2 x 0,5mm²

End-stop 2 x 0,5mm² 2 x 1mm² 2 x 1,5mm²

Aerial connection RG58 - max. 10 m

Encoder connection Shielded cable 2402C 22AWG - max. 5 m

UE1 E3

1234

5678910

10 11 1 2 3 5 7 C1 FA

24 12 0

- AMP. S+

- A.C.T.+

- S. DELAY +

L1T L2T

FA K E WVUF

Pag.

7- Manual code:

319T92

319T92 ver.

2.0

2.0 11/2012 © CAME cancelli automatici s.p.a.

The data and information reported in this installation manual are susceptible to change at any time and without obligation to notify users.

Anchoring and installing the box

Use a ø 5 drill bit to bear a hole observing the

distance between the centres as specified in

paragraph 5.3, and secure the control panel

to the ground guide using M 4x39 screws

(provided).

Red

Black

E306/E456 Ratiomotor

LINE

-ENC+

ZE7

CONTROL

BOARD

FUSE 5x20

UE1 E3

10 11 12357C1 FA

LINE

-ENC+

ZE7

CONTROL

5A BOARD

FUSE 5x20

UE1 E3

10 11 12357C1 FA

LINE

-ENC+

ZE7

CONTROL

BOARD

FUSE 5x20

UE1 E3

11 1 2357C1 FA

EMEGA

The data and information reported in this installation manual are susceptible to change at any time and without obligation to notify users.

Pag.

8- Manual code:

319T92

319T92 ver.

2.0

2.0 11/2012 © CAME cancelli automatici s.p.a.

Electrical connections

Gearmotor

230V (a.c.) max. 400 W single-phase motor

Power supply

Power supply to the

230V AC 50/60 Hz

control panel

Terminals for powering the

24V AC accessories.

Overall

allowed power: 20W

#!-%

LINE

-ENC+

ZE7

CONTROL

5A BOARD

FUSE 5x20

UE1 E3

11 1 2 3 5 7

(E881)

Pag.

9- Manual code:

319T92

319T92 ver.

2.0

2.0 11/2012 © CAME cancelli automatici s.p.a.

The data and information reported in this installation manual are susceptible to change at any time and without obligation to notify users.

Dip 9 in ON = Gate open warning light Contact rated for: 24 V - 3 W

Max.).

Indicates that gate is open.

Dip 9 in OFF = 24V-15W max. electric lock

Flashing light (contact rated for: 230V AC - 25W Max.)

Flashes while gate opens and closes.

Courtesy lamp Contact rated for: 230 V - 60 W Max.):

lights up the parking area, following an opening

command it stays on for a fixed 5 minutes and 30

seconds.

Signalling and lighting devices

LINE

-ENC+

ZE7

CONTROL

BOARD

FUSE 5x20

UE1 E3

11 1 2 3 5 7

DIR Delta-S

LINE

-ENC+

ZE7

CONTROL

BOARD

FUSE 5x20

UE1 E3

11 1 2 3 5 7

Delta

./ # .#



The data and information reported in this installation manual are susceptible to change at any time and without obligation to notify users.

Pag.

10 - Manual code:

319T92

319T92 ver.

2.0

Safety devices

C1 = (N.C.) contact for reopening while closing

- Input for safety devices like photocells, sensitive

edges and other devices that comply with EN

12978 regulations. While the door is closing,

opening the contact will invert movement until it is

fully openend.

If unused, set DIP-switch 7 to ON.

Inhaltsverzeichnis

Andere CAME Bedienfeld Handbücher

CAME

CAME ZL65 Bedienungsanleitung

CAME

CAME Z Series Bedienungsanleitung

CAME

CAME ZG6 Bedienungsanleitung

CAME

CAME Z Series Bedienungsanleitung

CAME

CAME TS4.3 Bedienungsanleitung

CAME

CAME Z Series Bedienungsanleitung

CAME

CAME Z Series Bedienungsanleitung

CAME

CAME ZA3P Bedienungsanleitung

CAME

CAME Z Series Bedienungsanleitung

CAME

CAME Z Series Bedienungsanleitung

CAME

CAME ZM3E Bedienungsanleitung

CAME

CAME Z Series Bedienungsanleitung

CAME

CAME S0001 Bedienungsanleitung

CAME

CAME Z Series Bedienungsanleitung

CAME

CAME ZLB24SA Bedienungsanleitung

CAME

CAME ZR24N Bedienungsanleitung

CAME

CAME ZLJ24 Bedienungsanleitung

CAME

CAME ZL90 Bedienungsanleitung

CAME

CAME 9T90EN Bedienungsanleitung

CAME

CAME ZA3N Bedienungsanleitung

CAME

CAME ZC3C Bedienungsanleitung

CAME

CAME ZL180 SERIES Bedienungsanleitung

CAME

CAME Z Series Bedienungsanleitung

CAME

CAME Z Series Bedienungsanleitung

Beliebte Bedienfeld Handbücher anderer Marken

RDZ

RDZ PC-HRX Bedienungsanleitung

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Technisches Handbuch

Efka

Efka Variocontrol V810 Bedienungsanleitung

Cebora

Cebora 208-10 Bedienungsanleitung

AMX

AMX AutoPatch CP-15 Bedienungsanleitung

Satel

Satel CA-6 KLED-S Bedienungsanleitung

Evolution

Evolution IQ plus 800 Bedienungsanleitung

Fagor

Fagor 8040 TCO CNC Bedienungsanleitung

Trane

Trane ComfortLink II XL950 Control Bedienungsanleitung

AKO

AKO PROCool AKO-17635-2 Bedienungsanleitung

ABB

ABB 6136/30M-101 Bedienungsanleitung

Telikou

Telikou BK-603 Belt Pack Bedienungsanleitung

Mapei

Mapei Mapeheat Thermo Touch Bedienungsanleitung

Bosch

Bosch D9412GV4 Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Bedienungsanleitung

Sminn

Sminn BOX L VF1L EI Bedienungsanleitung

Balboa

Balboa TP600 Bedienungsanleitung

Nice

Nice HSCU1 Technische Daten