CamFive EMB HT Series Bedienungsanleitung
HT1501 / HT1502
OPERATION MANUAL
2
Button Descriptions
Pág. Pág.
Pág. Pág.
Pág.
Pág.
Pág.
Beginning
Setting up a hat Loading a Design
Maintenance
Setting up the hat hoop onto
the embroidery machine
Troubleshooting
and FAQ
46
10 14
18
8
21
3
General
Info
The main screen displays embroider-
ing design and its status, please touch
the surrounding buttons to act corre-
sponding operations, please use the
direction keys to move the frame and
set the moving speed.
4
Button Descriptions
Machine is in “Emb Release” state, click
to take “Emb Confirm” (confirm the
design) operation.
Machine is in “Emb Confirm” state, click
to take “Emb Release”(delete design/
start over) operation.
Machine is in normal embroidery mode,
click to switch to idling mode.
Machine is in “High Speed idling” mode,
click to switch to a dierent embroidery
mode.
Machine is in “Low Speed idling” mode,
click to switch to a dierent embroidery
mode.
Machine is in “Auto change color, man-
ually start” color change mode, click to
switch to other color change modes.
Machine is in “Manually Change color”
color change mode, click to switch to
other color change modes
Machine is in “Auto Change Color, auto
start” color change mode, click to
switch to other color change modes.
Activate design managing function and
other management functions.
Open Machine parameter settings win-
dow to modify parameters.
Set Color change sequence of current
Embroidery Design
Activate main shaft origin (main shaft
stops at 100 degrees).
Change Needle.
Go to home position.
Go to End position.
Trim Thread.
Open “Embroidery Help Functions”
window.
Open “Other Functions” window.
Increase Speed.
Decrease Speed.
5
Connect the
USB drive onto
the side of the
Control Panel.
Beginning
In order to start, you must make
sure all designs are in DDB or DST
Format, onto the USB disk you will
be utilizing.
Setting up
your material
Setting up a flat item
What will you need?
A shirt or cloth you will like to embroider over
6
1
The proper size hoop to mount
the material to the machine
Pull away backing (material
to embroider over)
To begin, lay your
material on a flat
surface and stretch
in order to remove
any creases.
7
Place the bottom
hoop under the
material you would like
to embroider
(for shirts it would be in
the inside of the shirt).
Make sure the pull
away backing is also
under the shirt
but on top of the hoop
that is inside the shirt.
2
3
Note: Make sure the screw for
the hoop is easily accessible,
in case you need to adjust the
tightness of the hoop)
Place the inner
hoop on the outside
of the material, in
which should be tight
and stretched out.
8
Now you can slide the hoop into the machine work arms, if working with a shirt
make sure the neck hole goes thru the center bar.
Both ends of the hoop should click into each side of the embroidery machine.
4
5
9
First make sure
the hoop is in
the center of the
metal bar that
is coming from
the embroidery
machine and the
tracks should
align.
Then push
the hoop all
the way to
the back, until
the screws
align with their
respective
holes.
1
2
Setting up the hat hoop onto
the embroidery machine
10
Now tighten the
screws with an
allen key, and
you are now able
to place a hat
onto the hoop.
3
Place the
stationary
hat hoop on
a flat surface,
and secure it
tightly onto
the surface.
1
Setting up a hat
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere CamFive EMB Nähmaschine Handbücher
