Campbell Hausfeld WL6000 Series Bedienungsanleitung

Since the air compressor and other

components (material pump, spray

guns, filters, lubricators, hoses, etc.)

used, make up a high pressure

pumping system, the following safety

precautions must be observed at all

times:

1. Read all manuals

included with this

product carefully. Be

thoroughly familiar

with the controls and

the proper use of the equipment.

Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described.

Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or

property damage! Retain instructions for future reference.

Operating Instructions WL6000 Series

IN203402AV 11/97

Breathable Air Warning

This compressor/pump is NOT

equipped and should NOT be used “as

is” to supply breathing quality air. For

any application of air for human

consumption, you must fit the air

compressor/pump with suitable in-line

safety and alarm equipment. This

additional equipment is necessary to

properly filter and purify the air to

meet minimal specifications for Grade

D breathing as described in

Compressed Gas Association

Commodity Specification G 7.1 - 1966,

OSHA 29 CFR 1910. 134, and/or

Canadian Standards Associations

(CSA).

DISCLAIMER OF WARRANTIES

IN THE EVENT THE COMPRESSOR IS

USED FOR THE PURPOSE OF

BREATHING AIR APPLICATION AND

PROPER IN-LINE SAFETY AND ALARM

EQUIPMENT IS NOT SIMULTANEOUSLY

USED, EXISTING WARRANTIES ARE

VOID, AND CAMPBELL HAUSFELD

DISCLAIMS ANY LIABILITY

WHATSOEVER FOR ANY LOSS,

PERSONAL INJURY OR DAMAGE.

MANUAL

STOP!

Record the Model No., Serial No. and

date of purchase located on the base

below the pump in the space below.

Model No. ____________________

Serial No. ____________________

Date of purchase _________________

Retain these numbers for future

reference.

Need

Assistance?

Call Us First!

1-800-543-8622

Oilless

Stationary

Compressors

questions, damaged or missing parts,

please call 1-800-543-6400 for customer

assistance or call the nearest Campbell

Hausfeld Authorized Service Center.

A listing of service center locations is

enclosed. Have the serial number,

model number and parts list (with

missing parts circled before calling).

Do not operate

unit if damaged

during shipping, handling or use.

Damage may result in bursting and

cause injury or property damage.

Oilless compressors are designed for

do-it-yourselfers with a variety of home

and automotive jobs. These compres-

sors will power spray guns, impact

wrenches and other tools. These units

operate without oil.

This manual contains information that

is very important to know and

understand. This information is

provided for SAFETY and to PREVENT

EQUIPMENT PROBLEMS. To help

recognize this information, observe the

following symbols.

Danger indicates

an imminently

hazardous situation which, if not

avoided, WILL result in death or serious

injury.

Warning indicates

a potentially

hazardous situation which, if not

avoided, COULD result in death or

serious injury.

Caution indicates a

potentially

hazardous situation which, if not

avoided, MAY result in minor or

moderate injury.

Notice indicates

important

information, that if not followed, MAY

cause damage to equipment.

After unpacking the unit, inspect

carefully for any damage that may have

occurred during transit. Make sure to

tighten fittings, bolts, etc., before

putting unit into service. In case of

!NOTICE

BUILT TO LAST

Safety Guidelines

Description

Unpacking

DO NOT RETURN THE

PRODUCT TO THE

RETAILER!

General Safety

Information

16.Do not direct paint or other sprayed

material at the compressor. Locate

compressor as far away from the

spraying area as possible to

minimize overspray accumulation

on the compressor.

17.When spraying or cleaning with

solvents or toxic chemicals, follow

the instructions provided by the

chemical manufacturer.

Location

It is extremely important to install the

compressor in a clean, well ventilated

area where the surrounding air

temperature will not be more than

100°F.

A minimum clearance of 4 inches

between the compressor and a wall is

required because objects could obstruct

air flow.

Do not locate the

compressor air

inlet near steam, paint spray, sandblast

areas or any other source of

contamination. This debris will damage

the motor.

TANK MOUNTING

This compressor is

extremely top

heavy. The unit must be bolted to the

floor with isolation pads or secured

with the wall cable (if provided) before

operating to prevent equipment

damage, injury or death.

The tank should be bolted to a

concrete floor or on a separate

concrete foundation. Vibration

isolators should be used between the

tank leg and the floor . When using

isolator pads, do not draw bolts tight.

Allow the pads to absorb vibrations. A

flexible coupling should be installed

between the tank and service piping.

The air compressor should be mounted

on a flat, even surface.

Operating Instructions

Oilless Stationary Compressors

engine/motor and check

immediately for the cause. Vibration

is generally a warning of trouble.

11.To reduce fire hazard, keep

engine/motor exterior free of oil,

solvent, or excessive grease.

Never remove or

attempt to adjust

safety valve. Keep safety valve free

from paint and other accumulations.

Never attempt to repair

or modify a tank!

Welding, drilling or any

other modification will weaken the

tank resulting in damage from rupture

or explosion. Always replace worn or

damaged tanks.

Drain liquid from

tank daily.

12.Tanks rust from moisture build-up,

which weakens the tank. Make sure

to drain tank regularly and inspect

periodically for unsafe conditions

such as rust formation and

corrosion.

13.Fast moving air will stir up dust and

debris which may be harmful.

Release air slowly when draining

moisture or depressurizing the

compressor system.

SPRAYING PRECAUTIONS

Do not spray flammable

materials in vicinity of

open flame or near

ignition sources including the

compressor unit.

14.Do not smoke when spraying paint,

insecticides, or other flammable

substances.

15.Use a face mask/

respirator when

spraying and spray in

a well ventilated area

to prevent health and

fire hazards.

!NOTICE

2. Follow all local electrical and safety

codes, as well as in the U.S., National

Electrical Codes (NEC) and Occupa-

tional Safety and Health Act (OSHA).

3. Only persons well acquainted with

these rules of safe operation should

be allowed to use the compressor.

4. Keep visitors away and NEVER allow

children in the work area.

5. Wear safety glasses

and use hearing

protection when

operating the pump

or unit.

6. Do not stand on or use the pump or

unit as a handhold.

7. Before each use, inspect compressed

air system and electrical components

for signs of damage, deterioration,

weakness or leakage. Repair or

replace defective items before using.

8. Check all fasteners at frequent

intervals for proper tightness.

Motors, electrical

equipment and controls

can cause electrical arcs

that will ignite a flammable gas or

vapor. Never operate or repair in or

near a flammable gas or vapor. Never

store flammable liquids or gases in the

vicinity of the compressor.

Compressor parts may

be hot even if the unit

is stopped.

9. Keep fingers away

from a running compressor; fast

moving and hot parts will cause

injury and/or burns.

10.If the equipment should start to

abnormally vibrate, STOP the

General Safety

Information (Continued)

Installation

WL6000 Series

Operating Instructions

Never use an extension

cord with this product.

Use additional air hose

instead of an extension

cord to avoid power loss and

permanent motor damage. Use of an

extension cord voids the warranty.

GROUNDING INSTRUCTIONS

1. This product is for use on a nominal

120 volt circuit and has a grounding

plug that looks like the plug

illustrated in Figure 2. Make sure the

product is connected to an outlet

having the same configuration as the

plug. This product must be

grounded. In the event of an

electrical short circuit, grounding

reduces risk of electrical shock by

providing an escape wire for electric

current. This product is equipped

with a cord having a grounding wire

with an appropriate grounding plug.

Plug must be plugged into an outlet

that is properly installed and

grounded in accordance with all local

codes and ordinances.

Improper use of

grounding plug can

result in a possible risk

of electrical shock!

Do not use a

grounding adapter

with this product!

2. If repair or replacement of cord or

plug is necessary, do not connect

grounding wire to either flat blade

terminal. The wire with insulation

having an external surface that is

green (with or without yellow

stripes) is the grounding wire.

Never connect

green (or green

and yellow) wire to a live terminal.

3. Check with a qualified electrician or

serviceman if grounding instructions

are not completely understood, or if

in doubt as to whether product is

properly grounded. Do not modify

plug provided; if it will not fit outlet,

have proper outlet installed by a

qualified electrician.

WIRING

1. Local electrical wiring codes differ

from area to area. Source wiring,

plug and protector must be rated for

at least the amperage and voltage

indicated on motor nameplate, and

meet all electrical codes for this

minimum.

2. Use a slow blow fuse or a circuit

breaker.

Overheating, short

circuiting and fire

damage will result from inadequate

wiring, etc.

NOTE: 120 volt, 15 amp units can be

operated on a 120 volt circuit under

the following conditions:

a. No other electrical appliances

or lights are connected to the

same branch circuit.

b. Voltage supply is normal.

c. Circuit is equipped with a 15

amp circuit breaker or a 15

amp slow blow fuse.

3. If these conditions cannot be met or

if nuisance tripping of current

protection device occurs, it may be

necessary to operate compressor

from a 120 volt, 20 amp circuit.

Pressure switch - Auto/Off Switch - In

the AUTO position, the compressor

shuts off automatically when tank

pressure reaches the maximum preset

pressure. In the OFF position, the

compressor will not operate. This

switch should be in the OFF position

when connecting or disconnecting the

TEST RESET

STOP!

Grounded Outlet

Grounded

Figure 2

Never use the

wood shipping

skids for mounting the compressor.

OPTIONAL MOUNTING

WALL CABLE INSTALLATION

Included with the safety cable are two

lag screws and washers.

Do not secure the

compressor with

toggle bolts into drywall. Drywall

sheeting or plaster will not support the

weight of the compressor.

1. Place an isolation pad beneath each

foot of the compressor to minimize

vibration.

2. Position the cable through the

baseplate as shown in Figure 1.

3. Place the screws through the washers

then through looped ends of cable.

4. Secure the screws to a stud within a

framed wall. Use anchors if the wall

is concrete.

ELECTRICAL INSTALLATION

All wiring and

electrical

connections should be performed by a

qualified electrician. Installation must

be in accordance with local codes and

national electrical codes.

Figure 1

Approx.

16-24” 2 x 4”

Wall Studs

Safety

Cable

Lag Bolt

Washer

Isolation

Pads

Installation (Continued)

Operation

Operating Instructions

Oilless Stationary Compressors

LUBRICATION

This is an oilless product and DOES

NOT require lubrication to operate.

BREAK-IN PROCEDURE

Do not attach air

chuck or other tool

to open end of hose until start-up has

been completed and unit checks OK.

IMPORTANT: Do not operate

compressor before reading instructions

or damage may result.

1. Turn regulator fully clockwise to

open air flow.

2. Turn switch to OFF position and plug

in power cord.

3. Turn switch to AUTO position and

run unit for 30 minutes to break in

the pump parts.

4. Turn regulator knob fully

counterclockwise. Compressor will

build to maximum preset pressure

and shut off.

5. Turn regulator knob clockwise to

cause air to bleed off. Compressor

will restart at a preset pressure.

6. Turn regulator knob

counterclockwise to shut off the air

and turn switch to Off position.

7. Attach chuck or other tool to open

end of hose. Turn the regulator on.

In the AUTO position, the compressor

pumps air into the tank. It shuts off

automatically when unit reaches its

maximum preset pressure. In the OFF

position, the pressure switch cannot

function and the compressor will not

operate. This switch should be in the

OFF position when connecting or

disconnecting the power cord from the

electrical outlet.

ASME SAFETY VALVE

Do not remove or

attempt to adjust

the safety valve!

This valve should be

checked under

pressure occasionally

by pulling the ring by

hand. If air leaks after

ring has been

Figure 3

MOISTURE IN COMPRESSED AIR

Moisture in compressed air will form

into droplets as it comes from an air

compressor pump. When humidity is

high or when a compressor is in

continuous use for an extended

period of time, this moisture will

collect in the tank. When using a

paint spray or sandblast gun, this

water will be carried from the tank

through the hose, and out of the

gun as droplets mixed with the spray

material.

IMPORTANT: This condensation

will cause water spots in a paint

job, especially when spraying other

than water based paints. If

sandblasting, it will cause the sand

to cake and clog the gun, rendering

it ineffective. A filter in the air line

(MP3105), located as near to the

gun as possible, will help eliminate

this moisture.

Drain

Petcock

Safety

Valve

Pressure

Switch

Regulator

Check Valve

(Opposite Side)

Off

Auto

Air Hose

Attachment

Discharge Tube

(Opposite Side)

Figure 4

power cord from the electrical outlet or

when changing air tools.

Regulator - The regulator controls the

amount of air pressure released at the

hose outlet.

ASME Safety Valve - This valve

automatically releases air if the tank

pressure exceeds the preset maximum.

Discharge tube - This tube carries

compressed air from the pump to the

check valve. This tube becomes very hot

during use. To avoid the risk of severe

burns, never touch the discharge tube.

Check valve - One-way valve that

allows air to enter the tank, but

prevents air in the tank from flowing

back into the compressor pump.

Drain Petcock - This valve is located on

the bottom of the tank. Use this valve

to drain moisture from the tank daily

to reduce the risk of corrosion.

Reduce tank pressure below 10 PSI,

then drain moisture from tank daily to

avoid tank corrosion. Drain moisture

from tank(s) by opening the drain

petcock located underneath the tank.

Figure 5

Operation (Continued)

The compressor should be checked

often for any visible problems and the

following maintenance procedures

should be performed each time the

compressor is used.

1. Pull ring on safety valve and allow it

to snap back to normal position.

Safety valve must

be replaced if it

cannot be actuated or it leaks air after

ring is released.

2. With compressor shut off and

pressure released: Drain moisture

from tank by opening drain cock

underneath tank (See Figure 7).

3. Turn power OFF and clean dust and

dirt from motor, tank, air

lines and pump cooling fins.

IMPORTANT: Unit should be located as

far from spraying area as hose will

allow to prevent over-spray from

clogging filter.

AIR FILTER

Check air filter to be sure it is clean. To

service a filter, remove the filter

housing cover. Remove filter and clean

in hot, soapy water (Paper filters

cannot be washed). Rinse and let dry.

Replace air filters that cannot be

cleaned. Place filter back in the housing

base. Replace cover.

LUBRICATION

This is an oilless type compressor

requiring no lubrication.

THERMAL OVERLOAD PROTECTOR

This compressor is

equipped with an

automatic reset thermal overload

protector which will shut off motor if it

becomes overheated.

WL6000 Series

Operating Instructions

If thermal overload protector shuts

motor OFF frequently look for the

following causes

1. Low voltage

2. Clogged air filter

3. Lack of proper ventilation

If the thermal

overload protector

is actuated, the motor must be allowed

to cool down before start-up is pos-

sible. The motor will automatically

restart without warning if left plugged

into electrical outlet and unit is

turned on.

TORQUE REQUIREMENTS

Connecting rod bolt . . . . . . . . 20 in. Ibs.

Compressor hd. bolts. . . 100-110 in. Ibs.

Motor bolts . . . . . . . . . . . . . . . 35 in. Ibs.

Mounting bolts . . . . . . . . . . . . 90 in. Ibs.

STORAGE

1. When not in use, store hose and

compressor in a cool, dry place.

2. Drain tank of moisture

3. Disconnect hose and hang open ends

down to allow any moisture to drain.

released, or valve is stuck and cannot

be actuated by ring, it MUST be

replaced.

REGULATOR KNOB (See Figure 6)

1. This knob controls air pressure to an

air operated tool, or paint spray gun.

2. Turning knob clockwise increases air

pressure at outlet.

3. Turning counterclockwise will lower

air pressure at outlet.

4. Fully counterclockwise will shut off

flow of air completely.

OUTLET PRESSURE GAUGE

1. This gauge shows at-a-glance, air

pressure at outlet. Air pressure is

measured in pounds per square inch

(PSI).

2. Be sure this gauge reads ZERO before

changing air tools or disconnecting

hose from outlet.

TANK PRESSURE GAUGE

Gauge shows pressure in tank

indicating compressor is building

pressure properly.

Disconnect power

source then release all

pressure from the

system before

attempting to install, service, relocate

or perform any maintenance.

Outlet

Pressure

Gauge

Regulator

Knob Tank

Pressure

Gauge

(Behind)

Figure 6

Figure 7

Operation (Continued)

Maintenance

Operating Instructions

Oilless Stationary Compressors

Troubleshooting Chart

Symptom Possible Cause(s) Corrective Action

1. No electrical power

2. Blown fuse

3. Breaker open

4. Thermal overload open

5. Pressure switch bad

6. Check valve defective

1. Poor contacts, line voltage incorrect

2. Shorted or open motor winding

3. Defective check valve or unloader

1. Incorrect size fuse, circuit overloaded

2. Defective check valve or unloader

1. Low voltage

2. Clogged air filter

3. Lack of proper ventilation/room

temperature too high

4. Check valve malfunction

1. Leaking, broken, or loose valves or

restricted air passage

2. Defective pressure switch unloader

3. Defective bearing on eccentric or

motor shaft

4. Cylinder or piston ring is worn or

scored

5. Loose bolts, tank not level

1. Plugged in? Check fuse/breaker or motor overload.

2. Replace blown fuse

3. Reset, determine cause of problem

4. Motor will restart when cool

5. Replace

6. Remove and replace check valve

Do not disassemble check valve

with air in tank; bleed tank

1. Check connections, check with voltmeter

2. Replace motor

3. Replace or repair

Do not disassemble check valve

with air in tank; bleed tank

1. Check for proper fuse, use time-delay fuse.

Disconnect other electrical appliances from circuit or

operate compressor on its own branch circuit.

2. Replace or repair

Do not disassemble check valve

with air in tank; bleed tank

1. Check with voltmeter

2. Clean filter (see Maintenance section)

3. Move compressor to well ventilated area

4. Replace

Do not disassemble check valve

with air in tank; bleed tank

1. Replace

2. Replace or repair as necessary

3. Replace

4. Replace or repair as necessary

5. Tighten bolts, shim tank to level position

Compressor will not run

Motor hums but cannot

run or runs slowly

Fuses blow/circuit

breaker trips repeatedly

Never use an extension

cord with this product

Thermal overload

protector cuts out

repeatedly

Knocks, rattles,

excessive vibration

WL6000 Series

Operating Instructions

Troubleshooting Chart (Continued)

Symptom Possible Cause(s) Corrective Action

1. Loose connections (fittings, tubing,

etc.)

2. Loose drain cock

3. Check valve leaking

1. Clogged intake filter

2. Air leaks in piping (on machine or in

outside system)

3. Broken inlet valves

4. Piston ring broken

5. Cylinder or piston ring is worn or

scored

1. Excessive water in tank

2. High humidity

1. Defective pressure switch

2. Excessive air usage

1. Excessive condensation in tank

2. Air leaks in piping (on machine or in

outside system)

3. Tank check valve leaking

Check valve stuck in an open position

1. Check all connections with soap and water solution

and tighten

2. Tighten

3. Disassemble check valve assembly, clean or replace

Do not disassemble check valve

with air in tank; bleed tank

1. Clean or replace

2. Replace leaking components or tighten as necessary

3. Have authorized service representative repair unit

4. Replace

5. Replace

1. Drain tank

2. Move to area of less humidity; use air line filter

1. Replace switch

2. Decrease air usage; compressor not large enough for

air requirement

1. Drain more often

2. Replace leaking components or tighten as necessary

3. Replace or repair as necessary

Do not disassemble check valve

with air in tank; bleed tank

Remove and replace check valve

Do not disassemble check valve

with air in tank; bleed tank

Tank pressure drops

when compressor shuts

off

Air output lower than

normal/low discharge

pressure

Excessive moisture in

discharge air

Compressor runs

continuously

Excessive starting and

stopping (auto start)

Air leaking from

unloader on pressure

switch

Operating Instructions

Oilless Stationary Compressors

WL6000 Series

Limited Warranty

1. DURATION: From the date of purchase by the original purchaser as follows: Standard Duty Products - One Year, Serious Duty Products - Two

Years, Extreme Duty Products - Three Years.

2. WHO GIVES THIS WARRANTY (WARRANTOR):

Campbell Hausfeld / Scott Fetzer Company, 100 Production Drive, Harrison, Ohio, 45030, Telephone: (513) 367-4811

3. WHO RECEIVES THIS WARRANTY (PURCHASER): The original purchaser (other than for purposes of resale) of the Campbell Hausfeld product.

4. WHAT PRODUCTS ARE COVERED BY THIS WARRANTY: Any Campbell Hausfeld air compressor, air tool or supplementary air accessory

supplied or manufactured by Warrantor.

5. WHAT IS COVERED UNDER THIS WARRANTY: Defects due to material and workmanship with the exceptions noted below.

6. WHAT IS NOT COVERED UNDER THIS WARRANTY:

A. Implied warranties, including those of merchantability and FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED FROM THE DATE OF

ORIGINAL PURCHASE AS STATED IN THE DURATION. If this product is used for commercial, industrial or rental purposes, the warranty will

apply for ninety (90) days from the date of purchase. Four cylinder single-stage and two-stage products are not limited to a ninety (90) day

warranty when used in commercial or industrial applications. Some States do not allow limitations on how long an implied warranty lasts,

so the above limitations may not apply to you.

B. ANY INCIDENTAL, INDIRECT, OR CONSEQUENTIAL LOSS, DAMAGE, OR EXPENSE THAT MAY RESULT FROM ANY DEFECT, FAILURE, OR

MALFUNCTION OF THE CAMPBELL HAUSFELD PRODUCT. Some States do not allow the exclusion or limitations of incidental or

consequential damages, so the above limitation or exclusion may not apply to you.

C. Any failure that results from an accident, purchaser’s abuse, neglect or failure to operate products in accordance with instructions provided

in the owner’s manual(s) supplied with product.

D. Pre-delivery service, i.e. assembly, oil or lubricants, and adjustment.

E. Normal adjustments or expendable items which are explained in the owner’s manual(s) provided with the product including but not

limited to belts and pressure switch.

F. Items or service that are normally required to maintain the product, i.e. lubricants, filters and gaskets, etc.

G. Gasoline engines and components are expressly excluded from coverage under this limited warranty. The Purchaser must comply with the

warranty given by the engine manufacturer which is supplied with the product.

H. Additional items not covered under this warranty:

1. All Compressors

Maintenance records must be provided to make warranty claim

a. Any component damaged in shipment or any failure caused by installing or operating unit under conditions not in accordance

with installation and operation guidelines.

b. Pump or valve failure caused by rain, excessive humidity or corrosive environments.

c. Cosmetic defects that do not interfere with compressor functionality.

d. Rusted tanks, including but not limited to rust due to improper drainage.

e. Check valves after the first year of ownership.

f. Drain cocks.

g. Motor capacitors.

h. Damage due to improper wiring.

2. Lubricated Compressors

a. Pump wear or valve damage caused by using oil not specified.

b. Pump wear or valve damage caused by any oil contamination or by failure to follow proper oil maintenance guidelines.

3. Belt Drive / Direct Drive / Gas Driven Compressors

a. Belts.

b. Ring wear from inadequate filter maintenance.

c. Manually adjusted load/unload and throttle control devices.

7. RESPONSIBILITIES OF WARRANTOR UNDER THIS WARRANTY: Repair or replace, at Warrantor’s option, products or components which are

defective, have malfunctioned and/or failed to conform within duration of the warranty period.

8. RESPONSIBILITIES OF PURCHASER UNDER THIS WARRANTY:

A. Deliver or ship the Campbell Hausfeld product or component to the nearest Campbell Hausfeld Authorized Service Center. Freight costs, if

any, must be borne by the purchaser.

B. Use reasonable care in the operation and maintenance of the products as described in the owner’s manual(s).

9. WHEN WARRANTOR WILL PERFORM REPAIR OR REPLACEMENT UNDER THIS WARRANTY:

A. Repair or replacement will be scheduled and serviced according to the normal work flow at the servicing location, and depending on the

availability of replacement parts.

B. If the purchaser does not receive satisfactory results from the Authorized Service Center, the purchaser should contact the Campbell

Hausfeld Product Service Department (see paragraph 2).

This Limited Warranty gives you specific legal rights and you may also have other rights which vary from State to State.

demander conseil ou appeler un Centre

De Service Autorisé Campbell Hausfeld.

Une liste de centres de services est ci-

inclus. Prière d’avoir le numéro de

série, numéro de modèle et liste de

parties (avec les parties manquantes

encerclées) avant d’appeler.

Ne pas

utiliser

un modèle qui a été endommagé

pendant le transport, la manipulation

ou l’utilisation. Le dommage peut

résulter en explosion et peut causer

des blessures ou dégâts matériels.

!AVERTISSEMENT

Puisque le compresseur d’air et les

autres pièces détachées (pompe,

pistolets, filtres, graisseurs, tuyaux, etc.)

font partie d’un système de haute

pression, il est nécessaire de suivre les

précautions suivantes:

1. Lire attentivement tous

manuels compris avec ce

produit. Se familiariser

avec ce produit, ses

commandes et son

utilisation.

S’il vous plaît lire et conserver ces instructions. Lire attentivement avant de monter, installer, utiliser ou de procéder à l’entretien du produit

décrit. Se protéger ainsi que les autres en observant toutes les instructions de sécurité, sinon, il y a risque de blessure et/ou dégâts matériels!

Conserver ces instructions comme référence.

Instructions D’Utilisation Series WL6000

IN203402AV 11/97

Avertissement D’Air Respirable

Ce compresseur/pompe n’est pas

équipé pour et ne devrait pas être

utilisé “comme soi” pour fournir de

l’air respirable. En cas d’applications

d’air pour la consommation humaine,

le compresseur d’air/pompe doit être

équipé avec de l’équipement de

sécurité en canalisation et d’alarme.

Cet équipement additionnel est

nécessaire pour filtrer et purifier l’air

afin d’atteindre les spécifications

minimales pour la respiration Grade D

décrites dans le Compressed Gas

Association Commodity Specification

G 7.1 - 1966, OSHA 29 CFR 1910. 134,

et/ou Canadian Standards

Associations (CSA).

DÉNÉGATION DES GARANTIES

SI LE COMPRESSEUR EST UTILISÉ POUR

LES APPLICATIONS D’AIR RESPIRABLE ET

L’ÉQUIPEMENT DE SÉCURITÉ EN

CANALISATION ET D’ALARME N’EST PAS

UTILISÉ SIMULTANÉMENT, LES

GARANTIES EN EXISTANCE SERONT

ANNULÉES, ET CAMPBELL HAUSFELD NIE

TOUTE RESPONSABILITÉ POUR N’IMPORTE

QUELLE PERTE, BLESSURE OU DOMMAGE.

!DANGER

MANUEL

BUILT TO LAST

ARRÊT!

Enregistrer le No. de Modèle, No. de

Série, et la Date d’Achat située sur la base

de la pompe dans l’espace ci-dessous.

No. de Modèle ____________________

No. de Série ____________________

Date d’Achat ____________________

Garder ces numéros pour référence.

Compresseur

Sans Huile

Les compresseurs sans huile sont conçus

pour les bricoleurs avec projets

domestiques et d’automobile. Ces

compresseurs servent à faire

fonctionner les postolets à peinture,

clés à choc et autres outils. Ces

modèles fonctionnement sans

huile.

Ce manuel contient de l’information très

importante qui est fournie pour la

SÉCURITÉ et pour ÉVITER LES PROBLÈMES

D’ÉQUIPEMENT. Rechercher les symboles

suivants pour cette information.

Danger

indique

une situation hasardeuse imminente

qui RÉSULTERA en perte de vie ou

blessures graves.

Avertis-

sement

indique une situation hasardeuse

potentielle qui PEUT résulter en perte

de vie ou blessures graves.

Attention

indique

une situation hasardeuse potentielle

qui PEUT résulter en blessures.

Avis

indique

de l’information importante pour

éviter le dommage de l’équipement.

Lors du déballage de ce produit,

l’examiner soigneusement pour

rechercher toute trace de dommage

susceptible de s’être produit en cours

de transport. Veiller à serrer tout

raccord, boulon, etc., avant de mettre

ce produit en service. En cas de

dommage ou de parties manquantes,

S.V.P. composer le 1-800-543-6400 pour

!AVIS

!ATTENTION

!AVERTISSEMENT

!DANGER

Directives De Sécurité

Déballage

Description

Généralités Sur La

Sécurité

NE PAS RENVOYER LE

PRODUIT AU

MARCHAND!

17. Suivre les instructions du fabriquant

pendant la pulvérisation ou le

nettoyage avec des solvants ou produits

chimiques toxiques.

ENDROIT

Il est très important d’installer le

compresseur dans un endroit propre et

bien ventilé où la température n’excédera

pas 38˚C.

Laisser un espace libre de 10,2 cm

(minimum) entre le compresseur et le mur

car les objets peuvent obstruer la

circulation d’air.

Ne pas

situer la

prise d’air du compresseur près de la

vapeur, un jet pulvérisé de peinture,

endroits de décapage au sable ou autre

sources de contamination. Le débris

endommagera le moteur.

MONTAGE

Ne jamais

utiliser

les palettes en bois d’expédition pour

le montage du compresseur.

MONTAGE AU PLANCHER

Si le modèle n’est pas fixé avec le câble

de mur, les pieds du compresseur

doivent être fixés à un plancher en

béton plat et égal ou sur une

fondation en béton séparée. Les

isolateurs de vibration doivent être

utilisés entre la jambe du réservoir et le

plancher. Ne pas trop serrer les boulons

afin de permettre que les tampons

absorbent les vibrations. Utiliser un

accouplement flexible entre le réservoir

et la tuyauterie de service.

compres-

seur est très lourd du haut. Le modèle

doit être boulonné au plancher avec

des tampons isolateurs ou fixé au câble

de mur (si fourni) avant son utilisation

pour éviter le dommage à

l’équipement, les blessures ou la mort.

MONTAGE DU CÂBLE DE MUR

Le câble de sécurité comprend deux vis

à tête carrée et rondelles.

!AVERTISSEMENT

!ATTENTION

2 Fr

Instructions d’Utilisation

Compresseur Sans Huile

2. Suivre tous les codes de sécurité

locaux ainsi que les National Electrical

Codes (NEC) and Occupational Safety

and Health Act (OSHA) des É-U.

3. Seules les personnes bien

familiarisées avec ces règles

d’utilisation doivent être autorisées

à se servir du compresseur.

4. Garder les visiteurs à l’écart de/et NE

JAMAIS permettre les enfants dans

l’endroit de travail.

5. Utiliser des lunettes de

sécurité et la protection

auditive pendant

l’utilisation du modèle.

6. Ne pas se tenir debout

sur/ni utiliser le modèle comme une

prise.

7. Inspecter le système d’air comprimé

et pièces détachées électriques pour

toute indication de dommage,

détérioration, faiblesse ou fuites

avant chaque utilisation. Réparer

ou remplacer toutes pièces

défectueuses avant l’utilisation.

8. Inspecter le degré de serrage de toutes

attaches par intervalles régulières.

Ne jamais essayer de réparer

ou de modifier un réservoir!

Le soudage, perçage ou autre

modifications peuvent affaiblir le

réservoir et peuvent résulter en

dommage de rupture ou d’explosion.

Toujours remplacer un réservoir usé,

fendu ou endommagé.

Les pièces du compresseur

peuvent être chaudes, même

si le modèle est hors circuit.

9. Garder les doigts à l’écart du

compresseur; les pièces mobiles et

chaudes peuvent causer des

blessures et/ou des brûlures.

10. Si l’équipement vibre anormalement,

ARRÊTER le moteur et l’inspecter

immédiatement. La vibration est

généralement une indication d’un

problème.

!ATTENTION

!AVERTISSEMENT

11. Pour réduire le risque d’incendie, garder

l’extérieur du moteur libre d’huile, de

solvant ou de graisse excessive.

Ne jamais

enlever

ou essayer d’ajuster la soupape de

sûreté. Tenir la soupape de sûreté libre

de peinture et d’autres accumulations.

Ne jamais essayer de réparer

ou de modifier un réservoir!

Le soudage, perçage ou autre

modifications peuvent affaiblir le

réservoir et peuvent résulter en

dommage de rupture ou d’explosion.

Toujours remplacer un réservoir usé,

fendu ou endommagé.

Purger le

réservoir

quotidiennement.

12. L’accumulation d’humidité cause la

rouille qui peut affaiblir le réservoir.

Purger le réservoir quotidiennement

et l’inspecter périodiquement pour

la rouille et la corrosion ou autre

dommage.

13. L’air mouvante peut agiter la

poussière et le débris qui peut être

dangereux. Lâcher l’air lentement

en purgeant l’humidité ou pendant

la dépressurisation du système du

compresseur.

PRÉCAUTIONS DE PULVÉRISATION

Ne pas pulvériser les

matériaux inflammables dans

un endroit de flamme ouverte ni près

d’une source d’ignition y compris le

compresseur.

14. Ne pas fumer pendant la pulvérisation

de la peinture, d’insecticides ou autres

matières inflammables.

15. Utiliser un masque /

respirateur pendant la

pulvérisation et pulvériser

dans un endroit bien ventilé

pour éviter le risque de

blessures et d’incendie.

16. Ne pas diriger la peinture ou autre

matériel pulvérisé vers le compresseur.

Situer le compresseur aussi loin que

possible de l’endroit de pulvérisation

pour réduire l’accumulation de

surpulvérisation sur le compresseur.

!AVERTISSEMENT

!AVIS

!DANGER

!AVERTISSEMENT

Généralités Sur La

Sécurité (Suite)

Installation

Andere Handbücher für WL6000 Series

Inhaltsverzeichnis

Sprachen:

Andere Campbell Hausfeld Luftkompressor Handbücher

Campbell Hausfeld

Campbell Hausfeld HM7500 Bedienungsanleitung

Campbell Hausfeld

Campbell Hausfeld MW2500 Series Datenblatt

Campbell Hausfeld

Campbell Hausfeld HJ3001 Series Bedienungsanleitung

Campbell Hausfeld

Campbell Hausfeld HL5404 Service-Handbuch

Campbell Hausfeld

Campbell Hausfeld HU3501 Bedienungsanleitung

Campbell Hausfeld

Campbell Hausfeld DC200100 Service-Handbuch

Campbell Hausfeld

Campbell Hausfeld HL410189 Handbuch

Campbell Hausfeld

Campbell Hausfeld FP2028999TT Service-Handbuch

Campbell Hausfeld

Campbell Hausfeld VT636600 Bedienungsanleitung

Campbell Hausfeld

Campbell Hausfeld FP209699 Service-Handbuch

Campbell Hausfeld

Campbell Hausfeld WL5000 Series Bedienungsanleitung

Campbell Hausfeld

Campbell Hausfeld HM7510 Bedienungsanleitung

Campbell Hausfeld

Campbell Hausfeld FP2051 Service-Handbuch

Campbell Hausfeld

Campbell Hausfeld FP260100 Kurzanleitung

Campbell Hausfeld

Campbell Hausfeld CT1001 Bedienungsanleitung

Campbell Hausfeld

Campbell Hausfeld DC260000 Service-Handbuch

Campbell Hausfeld

Campbell Hausfeld HL300000 Anwendungshandbuch

Campbell Hausfeld

Campbell Hausfeld IN629500AV Service-Handbuch

Campbell Hausfeld

Campbell Hausfeld HS5610 Bedienungsanleitung

Campbell Hausfeld

Campbell Hausfeld DP4615 Bedienungsanleitung

Campbell Hausfeld

Campbell Hausfeld HS581600AJ Anwendungshandbuch

Campbell Hausfeld

Campbell Hausfeld VH300300 Gebrauchs- und Pflegehandbuch

Campbell Hausfeld

Campbell Hausfeld IN626100AV Bedienungsanleitung

Campbell Hausfeld

Campbell Hausfeld VT6367 Service-Handbuch

Beliebte Luftkompressor Handbücher anderer Marken

Sparmax

Sparmax DC-25XR Bedienungsanleitung

KAESER

KAESER M122 Bedienungsanleitung

Briggs & Stratton

Briggs & Stratton Air Compressor Bedienungsanleitung

Fini

Fini F3GST2TK Bedienungsanleitung

Industrial Air

Industrial Air CP1580325 Programmierhandbuch

Ingersoll-Rand

Ingersoll-Rand UP6 20 HP Bedienungsanleitung

Hitachi

Hitachi EC99S Bedienerhandbuch

Parkside

Parkside PKO 270 A1 Bedienungsanleitung

Clas Ohlson

Clas Ohlson QIE-ZTH-15 Bedienungsanleitung

Ferm

Ferm CRM1046 Bedienungsanleitung

BE AC153 Bedienungsanleitung

RIDGID

RIDGID OF25150A Bedienungsanleitung

Johnson Controls

Johnson Controls QUANTUM LX Handbuch

Sears

Sears Craftsman 919.167463 Bedienungsanleitung

Ring Automotive

Ring Automotive RAC700 Bedienungsanleitung

Craftsman

Craftsman 919.152144 Bedienungsanleitung

Alkin

Alkin W3 Series Bedienungsanleitung

Fubag

Fubag F1 241/24 CM2 Bedienungsanleitung