Campbell Hausfeld Framing Nailer JB3495 Bedienungsanleitung

General Safety Information

This manual contains safety, operational

and maintenance information.

Read this manual and

understand all safety

warnings and instructions

before operating the nailer.

Contact your Campbell

Hausfeld representative if

you have any questions.

CALIFORNIA PROPOSITION 65

You can create dust when

you cut, sand, drill or grind

materials such as wood,

paint, metal, concrete, cement, or other

masonry. This dust often contains

chemicals known to cause cancer, birth

defects, or other reproductive harm.

Wear protective gear.

OPERATOR’S RESPONSIBILITY:

Before operating the nailer, read and

understand all safety warnings and

labels. Follow the operating

instructions outlined in this manual.

EMPLOYER’S RESPONSIBILITY:

Distribute this instruction manual to all

users before allowing use of the nailer.

Ensure all operators read, understand

and follow all safety warnings, labels and

instructions outlined in this manual.

Danger

indicates

an imminently hazardous situation

which, if not avoided, WILL result in

death or serious injury.

●●

Do not use any type

of flammable gases or

oxygen as a power

source for the nailer.

Use filtered,

lubricated, regulated

compressed air only. Use of a

compressed gas instead of

compressed air may cause the nailer

to explode which will cause death or

serious personal injury.

●●Do not exceed

maximum operating

pressure of the nailer

(120 psi). The nailer

will not function

properly. Do not use a

compressed air source capable of

more than 200 psi. The nailer could

explode which will cause death or

serious personal injury.

●●Never use gasoline or

other flammable

liquids to clean the

nailer. Never use the

nailer in the presence

of flammable liquids or gases. Vapors

could ignite by a spark and cause an

explosion which will result in death

or serious personal injury.

●●Always remain in a

firmly balanced

position when

using or handling

the nailer.

●●Do not modify or

disable the Work

Contact Element

(WCE). Do not tie

or tape the WCE

or trigger in a

depressed

position. Death or serious personal

injury could result.

Operating Instructions Model JB3495

●●Do not touch

the trigger

unless driving

nails. Never

attach air line

to nailer or

carry nailer

while touching

the trigger. The

tool could eject a fastener which

will result in death or serious

personal injury.

Warning

indicates

a potentially hazardous situation

which, if not avoided, COULD result in

death or serious injury.

●●Always

disconnect

nailer from air

line before

clearing jams,

adjusting or

servicing the

nailer, relocating the nailer, or

when the nailer is not in use.

Always reconnect the air line

BEFORE loading any fasteners.

Framing Nailer

Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described.

Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury, death and/or

property damage! Retain instructions for future reference.

IN726600AV 7/08

Campbell Hausfeld Nailers meet or exceed Industries’ Standards as set forth by the American National

Standard Institute/International Staple, Nail and Tool Association in ANSI/ISANTA SNT-101-2002.

Table Of Contents

General Safety . . . . . . . . . . . . 1-2

Specifications . . . . . . . . . . . . . . 2

Operating The Nailer . . . . . . . . 3

Operational Modes. . . . . . . . . . 4

Troubleshooting . . . . . . . . . . . . 7

Fasteners . . . . . . . . . . . . . . . . . . 7

Warranty . . . . . . . . . . . . . . . . . . 8

Description

This nailer is designed for framing,

trusses, sub-floors, sheathing, exterior

decks, and pallet/create assembly.

Features include: convenient top loading

magazine, no-mar tip, adjustable

exhaust, single cycle trigger, and an

adjustable depth of drive mechanism.

MANUAL



OCO2

120 psi

MAX.

Locate model and date code

on tool and record below:

Model No. ________________________

Date Code ________________________

Retain these numbers for

future reference.

For parts, product & service information

visit www.chpower.com

See Warranty on page 8 for important information about commercial use of this product.

The nailer could eject a fastener

causing death or serious personal

injury.

●●Protect your eyes

and ears. Wear Z87

safety glasses, with

side shields. Wear

hearing protection.

Employers and users are

responsible for ensuring the user or

anyone near the nailer wears this

safety protection. Serious eye

injury or permanent hearing loss

could result.

●●Do not use a

check valve or

any other

fitting which

allows air to

remain in the

nailer. Death or

serious personal injury could occur.

●●Never place

hands or any

other body

parts in the nail

discharge area

of the nailer.

The nailer might

eject a fastener and could result in

death or serious personal injury.

●●Never carry the

nailer by the air

hose or pull the

hose to move

the nailer or a

compressor. Keep

hoses away from

heat, oil and sharp edges. Replace

any hose that is damaged, weak or

worn. Personal injury or tool

damage could occur.

●●Always assume the nailer contains

nails. Never use the nailer as a toy.

Do not engage in horseplay. Always

keep others at a safe distance from

the work area in case of accidental

discharge of nails. Never point the

nailer at anyone. Accidental

triggering of the nailer could result

in death or serious personal injury.

●●Do not drive a

nail on top of

other nails. The

nail could glance

and cause death

or a serious

puncture wound.

●●Do not operate

or allow anyone

else to operate

the nailer if any

warnings or

warning labels

are not legible.

Warnings or warning labels are located

on the nailer magazine and body.

●●Never leave the nailer unattended or

connected to an air compressor when

not in use. Serious personal injury

can occur if someone picks up and

uses the nailer without knowing the

correct way to operate the nailer.

●●Do not drop or throw the tool.

Dropping or throwing the tool can

result in damage that will make the

tool unusable or unsafe. If the tool

has been dropped or thrown,

examine the tool closely for bent,

cracked or broken parts and air

leaks. STOP and repair before using

or serious injury could occur.

Caution

indicates

a potentially hazardous situation which,

if not avoided, MAY result in minor or

moderate injury.

●●Do not modify or alter the nailer or

any nailer parts. Do not use the nailer

if any shields or guards are removed

or altered. Do not use the nailer as a

hammer. Personal injury or tool

damage may occur.

●●

Avoid long extended periods of work

with the nailer. Stop using the nailer

if you feel pain in hands or arms.

●●Always

check that

the Work

Contact

Element

(WCE) is

operating

properly. A

nail could

accidentally

be driven if the WCE is not working

properly. Personal injury may occur

(See "Checking the Work Contact

Element" Section).

●●Disconnect air supply and release

tension from the pusher before

attempting to clear jams because

fasteners can be ejected from the

front of the nailer. Personal injury

may occur.

Notice

indicates

important information, that if not

followed, may cause damage to

equipment.

●●Avoid using the nailer when the

magazine is empty. Accelerated

wear on the nailer may occur.

●●Clean and check all air supply hoses

and fittings before connecting the

nailer to an air supply. Replace any

damaged or worn hoses or fittings.

Tool performance or durability may

be reduced.

●●Air compressors providing air to the

nailer should follow the

requirements established by the

American National Standards

Institute Standard B19.3-1991;

Safety Standard for Compressors for

Process Industries. Contact your air

compressor manufacturer for

information.

Operating Instructions

!WARNING

JB3495

• REQUIRES

(SCFM with 16 nails 2.5

per minute @ 90 psi)

• AIR INLET 1/4” NPT

• NAIL LENGTH 2” to

RANGE 31⁄2”

• NAIL SHANK 0.113” to

RANGE 0.131”

• MAGAZINE CAPACITY 75-105

• WEIGHT 9 lbs 2 oz

• LENGTH 18.50”

• HEIGHT 15.00”

• MAX. PRESSURE 120 psi

• PRESSURE RANGE 70 - 120 psi

Nailer Components And Specifications Adjustable Direction Exhaust Deflector

Nail Loading Area

Magazine

Trigger

Warning Labels

(Backside)

Nail

Discharge Area

Work Contact

Element

www.chpower.com

Debris

Shield

Operating The Nailer

Read this manual and understand

all safety warnings and instructions

before operating the nailer.

LUBRICATION

This nailer requires lubrication before

using the nailer for the first time and

before each use. If an inline oiler is

used, manual lubrication through the

air inlet is not required on a daily basis.

The work

surface

can become damaged by excessive

lubrication. Proper lubrication is the

owner’s responsibil- ity. Failure to

lubricate the nailer properly will

dramatically shorten the life of the nailer

and void your warranty.

1. Disconnect

the air

supply from

the nailer

to add

lubricant.

2. Turn the nailer

so the air inlet

is facing up.

Place 4-5 drops

of 30 W non-

detergent oil

into air inlet.

Do not use

detergent oils, oil additives, or air

tool oils. Air tool oils contain

solvents which will damage the

nailer’s internal components.

3. After adding oil,

run nailer briefly.

Wipe off any

excess oil from

the cap exhaust.

REMOVING NO-MAR DECKING TIP

1. Disconnect air

supply from

nailer.

2. Remove all fasteners from magazine

(See UNLOADING THE

NAILER).

3. Remove no-mar tip retaining ring.

4. Pry no-

mar tip

away

from the

work

contact

element.

5. Replace

retaining

ring onto

no-mar

tip, then

store tip

in safe

place for future use.

INSTALLING NO-MAR DECKING TIP

1. Disconnect air

supply from

nailer.

2. Remove all fasteners from magazine

(See UNLOADING THE NAILER).

3. Remove retaining ring from no-mar

tip.

RECOMMENDED HOOKUP

1. The air

compressor

must be able

to maintain a

minimum of 70

psi when the nailer is being used.

An inadequate air supply can cause

a loss of power and inconsistent

driving.

2. An oiler can be

used to provide oil

circulation through

the nailer. A filter

can be used to

remove liquid and

solid impurities which can rust or

“gum up” internal parts of the

nailer.

3. Use 3/8” air

hoses with a

minimum

working

pressure of 150 psi. Use 1/2” air

hoses for 50’ run or longer. For

better performance, install a 3/8”

quick plug (1/4” NPT threads) with

an inside diameter of .315” (8mm)

on the nailer and a 3/8” quick

coupler on the air hose.

4. Use a pressure regulator on the

compressor, with an operating

pressure of 0 - 125 psi. A pressure

regulator is required to control the

operating pressure of the nailer

between 70 and 120 psi.

NO-MAR DECKING TIP

The no-mar decking tip is designed to

eliminate marks caused by the serrated

work contact element (WCE). The no-

mar tip may be removed if not

required (See REMOVING NO-MAR

DECKING TIP). Use tool in single cycle

mode (SEE OPERATIONAL MODES)

when no-mar tip is in place.



70 psi

Min.

OIL

120 psi

Max.

Model JB3495

Retaining

Ring

No-Mar Tip

Work

Contact

Element

No-

Mar

Tip

Recommended Hookup

Quick

Coupler

Air

Hose

Quick Plug

(Optional)

Quick

Coupler

(Optional)

Oiler

Regulator

Filter

Quick

Plug

www.chpower.com

4. Carefully

place no-

mar tip

over the

end of

work

contact

element.

Position

tip onto

WCE

making certain serrated gooves on

each piece are in line and fit snugly

together.

5. Position

retaining

ring on no-

mar tip and

press firmly

in place.

6. Check

that the

WCE and

trigger

move up

and down

freely

without

sticking or

binding.

Operational Modes

Always

know the

operational mode of the nailer before

using. Failure to know the operational

mode could result in death or serious

personal injury.

This stick framing nailer may be

operated in the “Single Cycle” or the

“Bottom Trip” mode. The nailer is

delivered in the single cycle mode. A

separate ‘red’ trigger for “Bottom

Trip” mode is included with tool as an

accessory.

SEQUENTIAL MODE

When the black trigger is installed,

nailer is in single cycle mode. This

method is recommended when precise

nail placement is required. Operation

in this mode requires trigger to be

pulled each time a nail is driven. Nailer

can be actuated by depressing the

Work Contact Element (WCE) against

work surface followed by pulling the

trigger.

The trigger must be released after each

fastener is driven to allow tool to reset.

Since the tool can only be actuated by

first removing the finger from the

trigger, this is considered to be a more

restrictive mode of operation, suitable

for less experienced users.

WORK CONTACT ELEMENT (WCE)

Check

the

operation of the Work Contact Element

(WCE) trip mechanism before each use.

The WCE must move freely without

binding through its entire travel

distance. The WCE spring must return

the WCE to its fully extended position

after being depressed. Do not operate

the nailer if the WCE trip mechanism is

not operating properly. Personal injury

may occur.

1. Disconnect

the air

supply

from the

nailer.

2. Remove all

nails from the

magazine

(see

Unloading

The Nailer).

Make

sure the

trigger

and work

contact

element

(WCE)

move

freely up

and

down without sticking or binding.

4. Reconnect

air supply to

the nailer.

5. Depress the

Work

Contact

Element

(WCE)

against the

work surface

without

pulling the

trigger. The

nailer MUST NOT OPERATE. Do not

use the tool if it operates without

pulling the trigger. Personal injury

may result.

BUMP MODE

When the red trigger is installed, the

nailer is in bottom trip mode. This

method is recommended when less

precise nail placement is required.

Operation in this mode requires trigger

to be depressed with nailer off of the

work surface. Then, the nose of the

nailer is tapped against the work

surface causing a nail to be driven.

Each time the Work Contact Element is

depressed, a nail is driven into the work

surface. Extreme care should be taken

because a nail will be driven when the

WCE is pressed against any surface.

Since the tool can be actuated without

removing the finger from the trigger,

this is considered to be a less restrictive

mode, suitable for more experienced

users.

MODE CONVERSION

To convert the tool from one mode to

the other:

1. Remove o-ring on the side of

trigger pin.

2. Remove trigger pin, trigger, and

trigger spring.

3. Switch out only the trigger.

4. Replace trigger spring, trigger,

trigger pin, and o-ring.

Do not attempt to modify the trigger

components in any manner and do not

attempt to use any other trigger

components other than those intended

for this tool.

Contact your Campbell Hausfeld

representative if you have any

questions.

Operating Instructions

Grooves

www.chpower.com

Mode Conversion

Trigger spring

O-ring

Trigger pin

Trigger

6. Remove

nailer from

work

surface. The

Work

Contact

Element

(WCE) must

return to its

original

down position. Pull the trigger. The

nailer MUST NOT OPERATE. Do not

use the tool if it operates while

lifted from the work surface.

Personal injury may result.

7. Pull the trigger and depress the

work contact element (WCE) against

the work surface. The nailer MUST

OPERATE when in bump mode. The

nailer MUST NOT OPERATE if in

sequential mode.

8. Depress the Work Contact Element

(WCE) against work surface. Pull the

trigger. The nailer MUST OPERATE.

LOADING THE NAILER

1. Always

connect

the tool to

the air

supply

before

fasteners.

2. Pull nail

pusher

mechanism

back until

pusher

engages

with

magazine latch.

3. Load strips of fasteners into the

magazine slot. Make sure that the

nails are placed into tool at the

proper orientation.

4. Squeeze

the pusher

and the

latch

together to

unlatch

pusher.

Make sure the head of the last nail is

under the head of the pusher.

UNLOADING THE NAILER

1. Always unload all fasteners before

removing tool from service.

Unloading is the reverse of loading,

except always disconnect the air

hose before unloading.

2. Pull nail

pusher

mechanism

back until

pusher

engages

with

magazine

latch.

3. Hold tool

upright so

nails will

slide

backwards

toward

magazine

slot.

4. Squeeze

the pusher

and latch

together to

unlatch the

pusher

once all

nails have

been removed.

ADJUSTING THE NAIL PENETRATION

The NS219001 and NS349001 nailers are

equipped with an adjustable depth of drive

feature. This allows the user to determine

how deep a fastener will be driven into the

work surface.

1. Adjust the operating pressure to a

pressure which will consistently

drive the fasteners. Do not exceed

the maximum operating pressure of

the nailer of 120 psi.

2. To adjust the depth-of-drive, loosen

the 4mm bolt on the top of nose. To

increase depth, push WCE in toward

nose as much as desired. Re-tighten

bolt. To decrease depth, pull WCE

out as much as desired. Re-tighten

bolt.

3. Make sure that the trigger and work

contact element (WCE) move freely

up and down without binding or

sticking after each adjustment.

ANTI-DRY FIRE

These tools are equipped with an Anti-Dry

Fire feature. This prevents the WCE from

being pushed in when only a few nails

remain. Simply load new nail clip behind

remaining nails to continue shooting.

ADJUSTING THE DIRECTION OF THE

EXHAUST

The nailers are

equipped with

an adjustable

direction

exhaust

deflector. This

is intended to

allow the user to change the direction

of the exhaust. Simply twist the

deflector to any direction desired.

CLEARING A JAM FROM THE NAILER

1. Disconnect

nailer from

air supply.

Model JB3495

Rotate

Nail pusher

mechanism Latch

Nail pusher

mechanism

Latch

www.chpower.com

Operating Instructions

www.chpower.com

2. Remove all

nails from

the

magazine

(see Loading/

Unloading).

Failure to do

so will cause

the nails to

eject from

the front of

the tool.

3. Insert a

screw-

driver

into the

nose of

the tool.

Push up

on the driver blade to free the

jammed nail.

4. Grab the

jammed

nail with

pliers

and

remove.

Technical Support

Please call our Nailer Hotline at 1-800-

543-6400 with any questions regarding

the operation or repair of this nailer or

for additional copies of this manual.

If calling from Ohio or outside of the

continental United States, please call

1-513-367-1182.

Fastener And Replacement

Parts

Use only

genuine

Campbell Hausfeld fasteners (or

equivalent - see Fastener Interchange

Information). Use only genuine

Campbell Hausfeld replacement parts.

Never substitute parts. Do not use

modified parts or parts which will not

give equivalent performance to the

original equipment. Tool performance,

safety and durability could be reduced.

When ordering replacement parts or

fasteners, specify by part number.

Nailer Repair

Nailer repairs must be performed by

qualified and experienced service

people ONLY.

Assembly Procedure For

Seals

When repairing a nailer, the internal

parts must be cleaned and lubricated.

Parker O-lube or equivalent must be

used on all o-rings. Each o-ring must be

coated with O-lube before assembling.

A small amount of oil must be used on

all moving surfaces and pivots. After

reassembling, a few drops of 30W non-

detergent oil, or equivalent, must be

added through the air line before

Model JB3495

Fasteners

JB3495 Tool will drive fasteners designed for: Porter Cable FC 350A, Hitachi NR83AA2, Senco FramePro 701XP, 751XP , Ridgid

R350CHA, DeWalt D51822, D51823, and Paslode F-3505.

Air leaking at trigger valve

Air leaking between

housing and nose

Air leaking between

housing and cap

Nailer skips driving nail

Nailer runs slow or has loss

of power

Nails are jammed in nailer

O-Rings in trigger valve housing are

damaged

Loose screws in housing

Damaged O-Rings

Damage to bumper

Loose screws

Damaged gasket

Worn bumper

Dirt in nose piece

Dirt or damage prevent nails or pusher

from moving freely in magazine

Damaged pusher spring

Inadequate air flow to nailer

Worn O-Ring on piston or lack of

lubrication

Damaged O-Ring on trigger valve

Air leaks

Cap gasket leaking

Nailer not lubricated sufficiently

Broken spring in cylinder cap

Exhaust port in cap is blocked

Guide on driver is worn

Nails are not correct size

Nails are bent

Magazine or nose screws are loose

Driver is damaged

Replace O-Rings. Check operation of Work

Contact Element (WCE)

Tighten screws

Replace O-Rings

Replace bumper

Tighten screws

Replace gasket

Replace bumper

Clean drive channel

Clean magazine

Replace spring

Check fitting, hose or compressor

Replace and lubricate O-Rings

Replace O-Rings

Tighten screws and fittings

Replace gasket

Lubricate nailer

Replace spring

Replace damaged internal parts

Replace guide

Use only recommended nails

Replace with undamaged nails

Tighten screws

Replace driver

Troubleshooting Guide

Stop using nailer immediately if any of the following problems occur. Serious personal injury

could result. Any repairs or replacements must be done by a Qualified Service Person or

Authorized Service Center.

Problem Cause Solution

www.chpower.com

Operating Instructions

www.chpower.com

Limited Warranty

1. DURATION: From the date of purchase by the original purchaser as follows: Campbell Hausfeld — Three (3) Years.

2. WHO GIVES THIS WARRANTY (WARRANTOR): Campbell Hausfeld / Scott Fetzer Company, 100 Production Drive,

Harrison, Ohio, 45030, Telephone: (800) 543-6400

3. WHO RECEIVES THIS WARRANTY (PURCHASER): The original purchaser (other than for purposes of resale) of the

Campbell Hausfeld product.

4. WHAT PRODUCTS ARE COVERED BY THIS WARRANTY: Any Campbell Hausfeld nailer, stapler, air tool, spray gun,

inflator or air accessory supplied or manufactured by Warrantor.

5. WHAT IS COVERED UNDER THIS WARRANTY: Substantial defects in material and workmanship which occur within the

duration of the warranty period.

6. WHAT IS NOT COVERED UNDER THIS WARRANTY:

A. Implied warranties, including those of merchantability and FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED

FROM THE DATE OF ORIGINAL PURCHASE AS STATED IN THE DURATION. If this product is used for commercial,

industrial or rental purposes, the warranty will apply for ninety (90) days from the date of purchase. Some States

do not allow limitation on how long an implied warranty lasts, so the above limitations may not apply to you.

B. ANY INCIDENTAL, INDIRECT, OR CONSEQUENTIAL LOSS, DAMAGE, OR EXPENSE THAT MAY RESULT FROM ANY

DEFECT, FAILURE, OR MALFUNCTION OF THE CAMPBELL HAUSFELD PRODUCT. Some States do not allow the

exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply

to you.

C. Any failure that results from an accident, purchaser’s abuse, neglect or failure to operate products in accordance

with instructions provided in the owner’s manual(s) supplied with product. Accident, purchaser's abuse, neglect or

failure to operate products in accordance with instructions shall also include the removal or alteration of any safety

devices. If such safety devices are removed or altered, this warranty is void.

D. Normal adjustments which are explained in the owner’s manual(s) provided with the product.

E. Items or service that are normally required to maintain the product, i.e. o-rings, springs, bumpers, debris shields,

driver blades, fuses, batteries, gaskets, packings or seals, fluid nozzles, needles, sandblast nozzles, lubricants,

material hoses, filter elements, motor vanes, abrasives, blades, cut-off wheels, chisels, chisel retainers, cutters,

collets, chucks, rivet jaws, screw driver bits, sanding pads, back-up pads, impact mechanism, or any other

expendable part not specifically listed. These items will only be covered for ninety (90) days from date of original

purchase. Underlined items are warranted for defects in material and workmanship only.

F. Cosmetic defects that do not interfere with the product’s function.

7. RESPONSIBILITIES OF WARRANTOR UNDER THIS WARRANTY: Repair or replace, at Warrantor’s option, products or

components which are defective, have malfunctioned and/or failed to conform within duration of the warranty period.

8. RESPONSIBILITIES OF PURCHASER UNDER THIS WARRANTY:

A. Provide dated proof of purchase and maintenance records.

B. Deliver or ship the Campbell Hausfeld product or component to the nearest Campbell Hausfeld Authorized Service

Center. Freight costs, if any, must be borne by the purchaser.

C. Use reasonable care in the operation and maintenance of the products as described in the owner’s manual(s).

9. WHEN WARRANTOR WILL PERFORM REPAIR OR REPLACEMENT UNDER THIS WARRANTY: Repair or replacement will be

scheduled and serviced according to the normal work flow at the servicing location, and depending on the availability

of replacement parts.

This Limited Warranty applies in the United States, Canada and Mexico only and gives you specific legal rights. You may

also have other rights which vary from state to state or country to country.

S’assurer que tous les utilisateurs lisent

et comprennent parfaitement les

notices de sécurité, étiquettes et

instructions décrites dans ce manuel.

Danger

indique

une situation hasardeuse imminente

qui RÉSULTERA en perte de vie ou

blessures graves.

●●Ne pas utiliser un gaz

inflammable ni

l’oxygène pour

alimenter la cloueuse.

Utilisez seulement de

l’air comprimé filtré,

lubrifié et réglé.

L’utilisation d’un gaz comprimé au

lieu de l’air comprimé peut faire

exploser la cloueuse et entraîner des

blessures graves ou mortelles.

●●Ne pas dépasser la

pression de service

maximale de la

cloueuse (827 kPa).

La cloueuse ne

fonctionnera pas

correctement. Ne pas

utiliser une source

d’air comprimé qui a une capacité de

plus que 1379 kPa. La cloueuse

pourrait exploser et causer des

blessures graves ou mortelles.

●●Ne jamais utiliser de

l’essence ni les fluides

inflammables pour le

nettoyage de la

cloueuse. Ne jamais

utiliser la cloueuse

près d’un liquide ou gaz inflammable.

Une étincelle peut allumer les vapeurs

et causer une explosion qui peut

résulter en perte de vie ou blessures

graves personnelles.

●●Toujours bien

s’équilibrer

pendant la

manipulation ou

l’utilisation de la

cloueuse.

●●Ne jamais

modifier ou

empêcher le

fonctionnement

du mécanisme de

déclenchement

par contact

(WCE) et ne

jamais maintenir

la gâchette enfoncée à l’aide de

Généralités Sur La Sécurité

Ce manuel contient des informations

concernant la sécurité, le

fonctionnement et l’entretien.

Lire attentivement ce manuel

et comprendre tous les

avertissements de sécurité et

les instructions avant

d’utiliser la cloueuse. Si vous

avez des questions, contacter un

représentant de Campbell Hausfeld.

PROPOSITION 65 CALIFORNIE

Vous pouvez créer de la

poussière en coupant,

ponçant, perçant ou meulant

les matériaux tels que le bois, la

peinture, le métal, le béton, le ciment

ou autre maçonnerie. Cette poussière

contient souvent des produits

chimiques reconnus pour causer le

cancer, les déformations congénitales

ou autres problèmes de la reproduction.

Portez de l’équipement de protection.

RESPONSABILITÉ DE L’UTILISATEUR

Avant d’utiliser cette cloueuse, prendre

connaissance de tous les avertissements

et des étiquettes concernant la sécurité.

Suivre les instructions données dans ce

manuel.

RESPONSABILITÉ DE L’EMPLOYEUR

Ce manuel d’instruction doit être mis à

la disposition de tous les utilisateurs

avant qu’ils ne se servent de la cloueuse.

ruban adhésif par exemple. Ceci

pourrait entraîner des blessures

graves ou mortelles.

●●Ne toucher à la

gâchette qu’au

moment de poser

des clous. Ne

jamais actionner

la gâchette

durant le

transport de la

cloueuse ou

durant le raccordement de celle-ci

au tuyau d’air comprimé. L’éjection

accidentelle d’un clou peut causer

des blessures graves ou mortelles.

Avertissment indique une situation

hasardeuse potentielle qui PEUT résulter

en perte de vie ou blessures graves.

●●

Toujours

débrancher le

tuyau d’air

comprimé de la

cloueuse avant

de dégager un

clou bloqué, de

régler, de réparer

ou de transporter la cloueuse ou lorsque

celle-ci n’est pas en service. Le

raccordement du tuyau d’air comprimé

doit toujours s’effectuer AVANT le

chargement du magasin. L’éjection

accidentelle d’un clou peut causer des

blessures graves ou mortelles.

Cloueuse à

Charpente

IN726600AV 7/08

Les Cloueuses Campbell Hausfeld conforment aux/ou dépassent les standards de l’American

National Standard/International Staple, Nail and Tool Association in ANSI/ISANTA SNT-101-2002.

Description

Cette cloueuse est conçue pour la

charpenterie, les armatures, les

sousplanchers, le revêtement, les terrasses

extérieures et les montages de palette/

caisse à claire-voie. Les caractéristiques

comprennent un chargeur du haut

pratique, une buse non-gâcheuse,

échappement orientable, gâchette à

cycle unique et un mécanisme de contrôle

de profondeur d’enfoncement.

MANUAL



827 kPa

Max.

Table Des Matières

Directives De Sécurité . . . . . . . . 1-2

Spécifications . . . . . . . . . . . . . . . 2

Fonctionnement De La Cloueuse .3

Modes De Fonctionnement . . . . . 4

Attaches . . . . . . . . . . . . . . . . . . . 6

Guide De Dépannage . . . . . . . . . 7

Garantie . . . . . . . . . . . . . . . . . . . 8

OCO2

Trouver le modèle et le code de date sur

l’outil et les inscrire plus bas.

N° de modèle ____________________

Code de date

______________________

Conserver ces numéros

comme référence.

Instructions D’Utilisation Modèle JB3495

S’il vous plaît lire et conserver ces instructions. Lire attentivement avant de monter, installer, utiliser ou de procéder à l’entretien du produit

décrit. Se protéger ainsi que les autres en observant toutes les instructions de sécurité, sinon, il y a risque de blessure et/ou dégâts matériels!

Conserver ces instructions comme référence.

Voir la Garantie à la page 16 pour de l’information importante sur l’utilisation commercial de ce produit.

●●

Protéger vos yeux avec

des lunettes de sécurité

Z87 à écrans latéraux et

vos oreilles avec un

protecteur auditif. Le

patron et l’utilisateur

sont responsables pour assurer que

l’utilisateur et ceux à proximité de la

cloueuse portent l’équipement de

securite, sinon, il y a risque de blessures

graves oculaires ou de dommage

permanent a l’ouie. sécurité, sinon, il y

a risque de blessures graves oculaires

l’équipement de sécurité, sinon, il y a

risque de blessures graves oculaires ou

de dommage permanent à l’ouie.

sécurité, sinon, il y a risque de blessures

graves oculaires ou de dommage

permanent à l’ouïe.

●●

Ne pas utiliser

un clapet ni

autre raccord

qui permet que

l’air reste dans

la cloueuse.

Cela

peut entraîner

des blessures graves ou mortelles.

●●Ne jamais poser

l’embout de

clouage sur la

main ou sur toute

autre partie du

corps. L’éjection

accidentelle d’un

clou peut causer des blessures

graves ou mortelles.

●●Ne jamais

transporter la

cloueuse par le

tuyau à air. Ne

jamais tirer sur le

tuyau pour

déplacer la

cloueuse ou le compresseur. Garder

le tuyau à air à l’écart de la chaleur,

l’huile et les objets pointus.

2-Fr

Remplacer les tuyaux endommagés,

faibles ou usés. Sinon, il y a risque

de blessures personnelles ou de

dommage à l’outil.

●●Toujours présumer que la cloueuse

contient des clous. Ne jamais traiter

la cloueuse de jouet. Toujours tenir

les autres personnes à l’écart de

l’endroit de travaille en cas

d’expulsion accidentelle. Ne jamais

diriger la cloueuse vers une autre

personne. Le déclenchement

accidentel de la cloueuse peut

causer la mort ou blessures graves.

●●

Ne jamais enfoncer

les clous un par

dessus l’autre. Le

clou pourrait

ricocher et causer

la mort ou une

blessure grave de

perforation.

●●Ne pas utiliser

la cloueuse/ni

permettre

qu’une autre

personne

l’utilise si les

avertissements

ou les étiquettes d’avertissement

situés sur le chargeur et corps de la

cloueuse ne sont pas lisables.

●●Ne jamais laisser la cloueuse sans

surveillance ni branchée à un

compresseur si hors-service. Il y a

risque de blessures graves si la

cloueuse est utilisée par une

personne qui ne connait pas les

instructions d’utilisation.

●●Ne pas échapper ni jeter l’outil car ceci

peut causer du dommage le rendant

dangereux à utiliser. Si l’outil s’est fait

échappé ou jeté, l’examiner

soigneusement afin de déterminer s’il

est courbé, fendu ou s’il y a des fuites

ou pièces détachées endommagées.

ARRËTER et réparer avant d’uitliser ,

sinon, il y a risque de blessures graves.

Attention

indique

une situation hasardeuse potentielle

qui PEUT résulter en blessures.

●●Ne pas modifier ni altérer la

cloueuse ou ces pièces. N’utilisez pas

une cloueuse si les écrans ou

protecteurs ont été enlevés ou

altérés. Cela peut entraîner des

blessures ou endommager l’appareil.

●●Éviter d’utiliser la cloueuse pour une

période de temps prolongée. Cesser

d’utiliser la cloueuse si l’on ressent

des douleurs dans les mains ou dans

les bras.

●●Toujours vérifier

le bon

fonctionnement

du mécanisme de

déclenchement

par contact

(WCE). L’éjection

accidentelle de

clou peut se

produire si ce mécanisme ne

fonctionne pas correctement et cela

pourrait entraîner des blessures. (Voir

“Vérification du mécanisme de

déclenchement par contact”).

●●Pour éviter l’expulsion d’une attache,

débrancher la source d’air et relâcher

la tension du poussoir avant de

procéder au déblocage. Sinon, il y a

risque de blessures graves.

Avis

indique

de l’information importante pour éviter

le dommage de l’équipement.

●●Éviter d’utiliser la cloueuse lorsque

le chargeur est vide. Sinon, il y a

risque d’usure accéléré de l’outil.

Instructions D’Utilisation

!AVERTISSEMENT

Pièces Détachées Et Spécifications

De La Cloueuse Déflecteur de direction

d’échappement réglable Endroit de

chargement

de clous

Chargeur

Gâchette

Décalcomanies de

sécurité (arrière)

Endroit d’expulsion

de clous Mécanisme de

déclenchement par contact

Écran de

débris

JB3495

• REQUIERT

(m3/min avec 16 clous 0,07

par minute @ 621 kPa)

• ARRIVÉE D’AIR 1/4 po NPT

• GAMME DE LONGUEUR 2 po -

DE CLOUS 3-1/2 po

• GAMME DE 0.113 po -

TIGES DE CLOUS 0.131 po

• CAPACITÉ

DU CHARGEUR 75-105

• POIDS 4,14 kg

• LONGUEUR 46,99 cm

• HAUTEUR 38,10 cm

• PRESSION MAX. 827 kPa

• GAMME DE PRESSION 483 kPa - 827 kPa

Inhaltsverzeichnis

Sprachen:

Andere Campbell Hausfeld Nagelpistole Handbücher

Campbell Hausfeld

Campbell Hausfeld CHN71500 Kurzanleitung

Campbell Hausfeld

Campbell Hausfeld CHN70900 Kurzanleitung

Campbell Hausfeld

Campbell Hausfeld IN715703AV Bedienungsanleitung

Campbell Hausfeld

Campbell Hausfeld IN729000AV Bedienungsanleitung

Campbell Hausfeld

Campbell Hausfeld NS319001 Handbuch

Campbell Hausfeld

Campbell Hausfeld IronForce IFN102 Bedienungsanleitung

Campbell Hausfeld

Campbell Hausfeld Air Powered Flooring Nailer / Stapler... Service-Handbuch

Campbell Hausfeld

Campbell Hausfeld CHN70600 Kurzanleitung

Campbell Hausfeld

Campbell Hausfeld IronForce IFN2190 Bedienungsanleitung

Campbell Hausfeld

Campbell Hausfeld SB3232 Bedienungsanleitung

Campbell Hausfeld

Campbell Hausfeld CHN50399 Service-Handbuch

Campbell Hausfeld

Campbell Hausfeld CHN70900 Service-Handbuch

Campbell Hausfeld

Campbell Hausfeld CHN10450 Bedienungsanleitung

Campbell Hausfeld

Campbell Hausfeld CHN70600 Service-Handbuch

Campbell Hausfeld

Campbell Hausfeld Brad Nailer CHN70200 Service-Handbuch

Campbell Hausfeld

Campbell Hausfeld NS2190 Bedienungsanleitung

Campbell Hausfeld

Campbell Hausfeld NB0040 Bedienungsanleitung

Campbell Hausfeld

Campbell Hausfeld Brad Nailer CHN70200 Kurzanleitung

Campbell Hausfeld

Campbell Hausfeld IN717702AV Bedienungsanleitung

Campbell Hausfeld

Campbell Hausfeld CHN104 Bedienungsanleitung

Campbell Hausfeld

Campbell Hausfeld IN715501AV Bedienungsanleitung

Campbell Hausfeld

Campbell Hausfeld SB504010 Bedienungsanleitung

Campbell Hausfeld

Campbell Hausfeld IronForce IFN219000 Handbuch

Campbell Hausfeld

Campbell Hausfeld CHN102 Bedienungsanleitung

Beliebte Nagelpistole Handbücher anderer Marken

Performance Tool

Performance Tool M643 Bedienungsanleitung

Hitachi

Hitachi VH650 - Fencing Nailer, Full Head Bedienungsanleitung

Parkside

Parkside PET 25 B1 Bedienungsanleitung

Senco

Senco Fusion Technology F-35XP Bedienungsanleitung

Grizzly

Grizzly G1847 Bedienungsanleitung

Ryobi

Ryobi R18N18G Bedienungsanleitung

Black & Decker

Black & Decker 492848-00 Bedienungsanleitung

HOLZMANN MASCHINEN

HOLZMANN MASCHINEN TN90 Bedienungsanleitung

Metabo HPT

Metabo HPT NR 3690DC Bedienungsanleitung

Surtek

Surtek CN650 Abmessungen und Installationsanleitung

Makita

Makita GF600 Bedienungsanleitung

Parkside

Parkside PET 25 B1 Bedienungsanleitung

Senco

Senco AirFree 25 Bedienungsanleitung

Freeman

Freeman P50LSLW Bedienungsanleitung

Aicon PRO

Aicon PRO DAC4507 Bedienungsanleitung

Makita

Makita AN923 Bedienungsanleitung

Grizzly

Grizzly T20644 Bedienungsanleitung

Black & Decker

Black & Decker 90514937 Bedienungsanleitung