Campbell Hausfeld IronForce IFN35650 Bedienungsanleitung

Description

This nailer is designed for decorative

trim, molding, window casings,

furniture trim and picture frame

assembly.

Features include: convenient

rear loading magazine which holds up to

100 nails, no-mar tip, adjustable exhaust,

single cycle trigger, quick clear nose, and

an adjustable depth of drive mechanism.

General Safety

Information

CALIFORNIA PROPOSITION 65

You can create dust when

you cut, sand, drill or grind

materials such as wood,

paint, metal, concrete, cement, or

other masonry. This dust often

contains chemicals known to cause

cancer, birth defects, or other

reproductive harm. Wear protective

gear.

Excessive exposure to vibration,

working in awkward positions and

repetitive work motions can cause

injury to hands and arms. Stop using

any tool if discomfort, numbness,

tingling or pain occur and consult a

physician.

This manual contains safety,

operational and maintenance

information.

Read this manual and

understand all safety

warnings and instructions

before operating the

nailer. Contact your

Campbell Hausfeld

representative if you have any

questions.

OPERATOR’S RESPONSIBILITY:

Before operating the nailer, read and

understand all safety warnings and

labels. Follow the operating

instructions outlined in this manual.

EMPLOYER’S RESPONSIBILITY:

Distribute this instruction manual to all

users before allowing use of the nailer.

Ensure all operators read, understand

and follow all safety warnings, labels

and instructions outlined in this

manual.

Danger indicates

an imminently

hazardous situation which, if not

avoided, WILL result in death or serious

injury.

•

Do not use any type

of flammable gases

or oxygen as a power

source for the nailer.

Use filtered,

lubricated, regulated

compressed air only.

Use of a compressed gas instead of

compressed air may cause the nailer

to explode which will cause death or

serious personal injury.

• Do not exceed

maximum operating

pressure of the nailer

(120 psi). The nailer

will not function

properly. Do not use

a compressed air

source capable of more than 200 PSI.

DANGER

The nailer could explode which will

cause death or serious personal

injury.

• Never use gasoline

or other flammable

liquids to clean the

nailer. Never use the

nailer in the presence

of flammable liquids

or gases. Vapors could ignite by a

spark and cause an explosion which

will result in death or serious

personal injury.

• Always remain in

a firmly balanced

position when

using or handling

the nailer.

• Do not modify or

disable the Work

Contact Element

(WCE). Do not tie

or tape the WCE

or trigger in a

depressed

position. Death or serious personal

injury could result.

Model IFN35650

IN725300AV 2/08

Campbell Hausfeld Nailers meet or exceed Industries’ Standards as set forth by the American National

Standard Institute/International Staple, Nail and Tool Association in ANSI/ISANTA SNT-101-2002.

Table Of Contents

General Safety . . . . . . . . . . . . . . . 1-3

Specifications . . . . . . . . . . . . . . . . . . 2

Operational Modes . . . . . . . . . . . . . 4

Operating The Nailer . . . . . . . . . 3-5

Troubleshooting . . . . . . . . . . . . . . . 6

Warranty . . . . . . . . . . . . . . . . . . . . . 7

MANUAL

OCO

Locate model and date code on

tool and record below:

Model No. ______________________

Date Code ______________________

Retain these numbers for

future reference.

Angle Finish Nailer

Operating Instructions Model IFN35650

Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described.

Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury, death

and/or property damage! Retain instructions for future reference.

See Warranty on page 7 for important information about commercial use of this product.

REMINDER: Keep your dated proof of purchase for warranty purposes!

Attach it to this manual or file it for safekeeping.

For parts, product & service information

visit www.chpower.com

General Safety

Information (Continued)

• Do not touch the

trigger unless

driving nails.

Never attach air

line to nailer or

carry nailer

while touching

the trigger. The

tool could eject a fastener which

will result in death or serious

personal injury.

Warning indicates

a potentially

hazardous situation which, if not

avoided, COULD result in death or

serious injury.

• Always

disconnect

nailer from air

line before

clearing jams,

adjusting or

servicing the

nailer, relocating the nailer, or when

the nailer is not in use. Always

reconnect the air line BEFORE

loading any fasteners. The nailer

could eject a fastener causing death

or serious personal injury.

• Protect your eyes and

ears. Wear Z87 safety

glasses, with side

shields. Wear hearing

protection. Employers

and users are

responsible for ensuring the user or

anyone near the nailer wears this

safety protection. Serious eye injury

or permanent hearing loss could

result.

WARNING

• Do not use a

check valve or

any other

fitting which

allows air to

remain in the

nailer. Death

or serious personal injury could

occur.

• Never place

hands or any

other body parts

in the nail

discharge area

of the nailer. The

nailer might eject

a fastener and could result in death

or serious personal injury.

• Never carry the

nailer by the air

hose or pull the

hose to move

the nailer or a

compressor. Keep

hoses away from

heat, oil and

sharp edges. Replace any hose that

is damaged, weak or worn. Personal

injury or tool damage could occur.

• Always assume the nailer contains

nails. Never use the nailer as a toy.

Do not engage in horseplay. Always

keep others at a safe distance from

the work area in case of accidental

discharge of nails. Never point the

nailer at anyone. Accidental

triggering of the nailer could result

in death or serious personal injury.

• Do not drive a

nail on top of

other nails. The

nail could glance

and cause death

or a serious

puncture wound.

• Do not operate

or allow

anyone else to

operate the

nailer if any

warnings or

warning labels

are not legible. Warnings or

warning labels are located on the

nailer magazine and body.

• Never leave the nailer unattended

or connected to an air compressor

when not in use. Serious personal

injury can occur if someone picks up

and uses the nailer without

knowing the correct way to operate

the nailer.

• Do not drop or throw the tool.

Dropping or throwing the tool can

result in damage that will make the

tool unusable or unsafe. If the tool

has been dropped or thrown,

examine the tool closely for bent,

cracked or broken parts and air

leaks. STOP and repair before using

or serious injury could occur.

Caution indicates a

potentially

hazardous situation which, if not

avoided, MAY result in minor or

moderate injury.

• Do not modify or alter the nailer or

any nailer parts. Do not use the

nailer if any shields or guards are

removed or altered. Do not use the

nailer as a hammer. Personal injury

or tool

damage may occur.

•

Avoid long extended periods of work

with the nailer. Stop using the nailer

if you feel pain in hands or arms.

CAUTION

Model IFN35650

Operating Instructions

!WARNING

Quick Clear Latch

Rubber No-Mar Tip

Nail Discharge Area

Nail Loading Area

Aluminum Magazine

Hard Anodized

Trigger

Warning Decal

Trilingual

Specification

Decal

Adjustable Direction

Exhaust Deflector

• REQUIRES: 1.8 SCFM with 10 nails

per minute @ 90 psi

• AIR INLET: 1/4 inch NPT

• NAIL SIZE RANGE: 1-1/2 inch to 2-

1/2 inch

• MAGAZINE CAPACITY:

100 Nails per load, 15 gauge

• WEIGHT: 5 lbs., 11 oz.

• LENGTH: 13-3/4 inch

• HEIGHT: 12-1/4 inch

• MAXIMUM PRESSURE: 120 psi

• PRESSURE RANGE: 70 - 120 psi

Nailer Components And Specifications

Nail Pusher Assembly

Adjustable

Depth

Control

www.chpower.com

RECOMMENDED HOOKUP

The illustration below shows the

recommended hookup for the nailer.

1. The air

compressor

must be able

to maintain a

minimum of

70 PSI when

the nailer is being used. An

inadequate air supply can cause a

loss of power and inconsistent

driving.

2. An oiler can be

used to provide oil

circulation through

the nailer. A filter

can be used to

remove liquid and

solid impurities which can rust or

“gum up” internal parts of the

nailer.

3. Use 3/8 inch

air hoses with

a minimum

working

pressure of

150 psi. Use 1/2 inch air hoses for

50 foot run or longer. For better

performance, install a 3/8 inch quick

plug (1/4 inch NPT threads) with an

inside diameter of .315 inch (8mm)

on the nailer and a 3/8 inch quick

coupler on the air hose.

4. Use a pressure regulator on the

compressor, with an operating

pressure of 0 - 125 PSI. A pressure

regulator is required to control the

operating pressure of the nailer

between 70 and 120 PSI.

General Safety

Information (Continued)

• Always check

that the Work

Contact

Element (WCE)

is operating

properly. A nail

could

accidentally be

driven if the

WCE is not

working properly. Personal injury

may occur (See "Checking the Work

Contact Element" Section).

• Disconnect air supply and release

tension from the pusher before

attempting to clear jams because

fasteners can be ejected from the

front of the nailer. Personal injury

may occur.

Notice indicates

important

information, that if not followed, MAY

cause damage to equipment.

• Avoid using the nailer when the

magazine is empty. Accelerated

wear on the nailer may occur.

• Clean and check all air supply hoses

and fittings before connecting the

nailer to an air supply. Replace any

damaged or worn hoses or fittings.

Tool performance or durability may

be reduced.

• Air compressors providing air to the

nailer should follow the

requirements established by the

American National Standards

Institute Standard B19.3-1991;

Safety Standard for Compressors for

Process Industries. Contact your air

compressor manufacturer for

information.

NOTICE

Operating The Nailer

Read this manual and understand

all safety warnings and

instructions before operating the

nailer.

LUBRICATION

This nailer requires lubrication before

using the nailer for the first time and

before each use. If an inline oiler is

used, manual lubrication through the

air inlet is not required on a daily basis.

The work surface

can become

damaged by excessive lubrication.

Proper lubrication is the owner’s

responsibil- ity. Failure to lubricate the

nailer properly will dramatically

shorten the life of the nailer and void

your warranty.

1. Disconnect the

air supply from

the nailer to

add lubricant.

2. Turn the nailer

so the air inlet

is facing up.

Place 4-5 drops

of 30 W non-

detergent oil

into air inlet. Do not use detergent

oils, oil additives, or air tool oils. Air

tool oils contain solvents which will

damage the nailer’s internal

components.

3. After adding oil,

run nailer briefly.

Wipe off any

excess oil from

the cap exhaust.

NOTICE

Model IFN35650

Operating Instructions

70 PSI

Min.

OIL

120 PSI

Max.

150 PSI WP

3/8 inch I.D.

Recommended Hookup

Quick

Plug

Quick

Coupler

Air

Hose

Quick Plug

(Optional)

Quick

Coupler

(Optional)

Oiler

Regulator

Filter

www.chpower.com

4. Reconnect air

supply to the

nailer.

5. Depress the

Work Contact

Element (WCE)

against the

work surface

without pulling

the trigger. The nailer MUST NOT

OPERATE. Do not use the tool if it

operates without pulling the

trigger. Personal injury may result.

6. Remove the

nailer from the

work surface.

The Work

Contact

Element (WCE)

must return to

its original down position. The

nailer MUST NOT OPERATE. Do not

use the tool if it operates while

lifted from the work surface.

Personal injury may result.

7. Pull the

trigger and

depress the

work

contact

element

(WCE) against the work surface. The

nailer MUST NOT OPERATE.

8. Depress

the Work

Contact

Element

(WCE)

against the

work surface. Pull the trigger. The

nailer MUST OPERATE.

LOADING THE NAILER

1. Always connect the tool to the air

supply before loading fasteners.

2. Insert one stick

of nails into

rear loading

slot while

holding tool

down so nails

will slide

forward in

magazine.

NOTE: Make

certain to insert

nail heads into

wide area at top of magazines with

nail points down.

Operating The Nailer

(Continued)

Operational Modes

Always know the

operational mode

of the nailer before using. Failure to

know the operational mode could

result in death or serious personal

injury.

THIS TOOL IS SOLD WITH A BLACK

SINGLE CYCLE TRIGGER. THIS TOOL

IS NOT INTENDED TO BE USED WITH

A RED BUMP CYCLE TRIGGER.

SINGLE CYCLE MODE

This method is

recommended

for precise nail

placement. This

mode requires

the trigger to

be pulled each time a nail is driven. The

nailer can be actuated by depressing

the WCE against the work surface

followed by pulling the trigger. Or the

nailer can be actuated by pulling the

trigger and then depressing the WCE

against the work surface.

The trigger must be released to reset

the tool before another nail can be

driven.

WORK CONTACT ELEMENT (WCE)

Check the opera-

tion of the Work

Contact Element (WCE) trip mechanism

before each use. The WCE must move

freely without binding through its

entire travel distance. The WCE spring

must return the WCE to its fully

extended position after being

depressed. Do not operate the nailer if

the WCE trip mechanism is not

operating properly. Personal injury may

occur.

1. Disconnect the

air supply from

the nailer.

2. Remove all

nails from the

magazine (see

Loading/

Unloading).

Make sure the

trigger and

work contact

element (WCE)

move freely up

and down

without sticking or binding.

CAUTION

WARNING

3. Press “Nail

Bypass Button”

in round hole in

the Nail Pusher

Mechanism and

pull back. This

allows the nail

clip to slide fully into the magazine.

4. Release the pusher. Allow pusher to

rest against nails. The nailer is now

loaded.

UNLOADING THE NAILER

1. Always unload all fasteners before

removing tool from service.

Unloading is the reverse of

loading, except always disconnect

the air hose before unloading.

2. Pull nail pusher

mechanism back

and press “Nail

Bypass Button.”

3. Hold tool

upright so nails

will slide out of

magazine.

4. Release the

Pusher.

ADJUSTING THE NAIL PENETRATION

The IFN35650 is equipped with an

adjustable depth of drive feature. This

allows the user to determine how deep a

fastener will be driven into the work

surface.

1. Adjust the

operating

pressure to

a pressure

which will

consistently

drive the

fasteners. Do not exceed the

maximum operating pressure of the

nailer of 110 psi.

Model IFN35650

Operating Instructions

www.chpower.com

Nail Pusher

Mechanism

Slot

Nail Bypass Button

Pusher

Mechanism

Nail

Nail Bypass Button

COUNTER-

CLOCKWISE CLOCKWISE

Movement

4. The door can

now be

rotated,

exposing the

jammed

fastener.

5. Remove the

jammed

fastener,

using pliers or

a screwdriver

if required.

6 Rotate door

back into the

closed

position.

7. Extend the

wire latch and

place over the

hooks on the

nose.

8. Close the latch

by pushing the

latch up and in

until the latch

snaps into

place.

Make sure the

trigger and

work contact

element (WCE)

move freely up

and down

without sticking or binding.

Operating The Nailer

(Continued)

To increase

depth of drive,

first pull up on

the upper

WCE, then

rotate

thumbwheel

to the left

(counter-

clockwise). To decrease depth of drive,

rotate thumbwheel to the right

(clockwise). Then release upper WCE

into detents which hold the

thumbwheel in place after each

adjustment.

3. Make sure that the

trigger and work

contact element

(WCE) move freely up

and down without

binding or sticking

after each adjustment.

ADJUSTING THE DIRECTION OF THE

EXHAUST

The IFN35650 is

equipped with an

adjustable

direction exhaust

deflector. This is

intended to allow

the user to change the direction of the

exhaust. Simply twist the deflector to

any direction desired.

CLEARING A JAM FROM THE NAILER

1. Disconnect the

air supply from

the nailer.

2. Remove all nails

from the

magazine (see

Loading/

Unloading).

Failure to do so

may cause the nails to eject from

the front of the nailer.

3. Undo latch by

pulling out and

down. The wire

latch will

disengage from

the hooks on the

nose.

Technical Support

Please call our Nailer Hotline at

1-800-543-6400 with any questions

regarding the operation or repair of

this nailer.

Fastener And Replacement

Parts

Use only 15 gauge

35° fasteners. Use only genuine

Campbell Hausfeld replacement parts.

Never substitute parts. Do not use

modified parts or parts which will not

give equivalent performance to the

original equipment. Tool performance,

safety and durability could be reduced.

When ordering replacement parts or

fasteners, specify by part number.

Nailer Repair

Nailer repairs must be performed by

qualified and experienced service

people ONLY.

Assembly Procedure For

Seals

When repairing a nailer, the internal

parts must be cleaned and lubricated.

Parker O-lube or equivalent must be

used on all o-rings. Each o-ring must be

coated with O-lube before assembling.

A small amount of oil must be used on

all moving surfaces and pivots. After

reassembling, a few drops of 30W non-

detergent oil or equivalent, must be

added through the air line before

testing.

WARNING

Movement

Fasteners Information

Nails used in the Campbell Hausfeld IFN35650 Angle Finish Nailer will also work in Sears 18329, Porter Cable DA250, Senco

SFN2B, SFN1 and SFN40.

Movement

Rotate

Model IFN35650

Operating Instructions

www.chpower.com

Air leaking at trigger

valve

Air leaking between

housing and nose

Air leaking between

housing and cap

Nailer skips driving

nail

Nailer runs slow or

has loss of power

Nails are jammed in

nailer

O-Rings in trigger valve housing are

damaged

Loose screws in housing

Damaged O-Rings

Damage to bumper

Loose screws

Damaged gasket

Worn bumper

Dirt in nose piece

Dirt or damage prevent nails or

pusher from moving freely in

magazine

Damaged pusher spring

Inadequate air flow to nailer

Worn O-Ring on piston or lack of

lubrication

Damaged O-Ring on trigger valve

Air leaks

Cap gasket leaking

Nailer not lubricated sufficiently

Broken spring in cylinder cap

Exhaust port in cap is blocked

Guide on driver is worn

Nails are not correct size

Nails are bent

Magazine or nose screws are loose

Driver is damaged

Replace O-Rings. Check operation of Work Contact

Element (WCE)

Tighten screws

Replace O-Rings

Replace bumper

Tighten screws

Replace gasket

Replace bumper

Clean drive channel

Clean magazine

Replace spring

Check fitting, hose or compressor

Replace and lubricate O-Rings

Replace O-Rings

Tighten screws and fittings

Replace gasket

Lubricate nailer

Replace spring

Replace damaged internal parts

Replace guide

Use only recommended nails

Replace with undamaged nails

Tighten screws

Replace driver

Troubleshooting Guide

Stop using nailer immediately if any of the following problems occur. Serious personal injury could result.

Any repairs or replacements must be done by a Qualified Service Person or Authorized Service Center.

WARNING

Problem Cause Solution

Model IFN35650

Operating Instructions

www.chpower.com

Limited Warranty

1. DURATION: From the date of purchase by the original purchaser as follows: One (1) Year.

2. WHO GIVES THIS WARRANTY (WARRANTOR): Campbell Hausfeld / Scott Fetzer Company, 100 Production Drive,

Harrison, Ohio, 45030, Telephone: (800) 543-6400

3. WHO RECEIVES THIS WARRANTY (PURCHASER): The original purchaser (other than for purposes of resale) of the

Campbell Hausfeld product.

4. WHAT PRODUCTS ARE COVERED BY THIS WARRANTY: Any Campbell Hausfeld nailer, stapler, air tool, spray gun,

inflator or air accessory supplied or manufactured by Warrantor.

5. WHAT IS COVERED UNDER THIS WARRANTY: Substantial defects in material and workmanship which occur within the

duration of the warranty period.

6. WHAT IS NOT COVERED UNDER THIS WARRANTY:

A. Implied warranties, including those of merchantability and FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED

FROM THE DATE OF ORIGINAL PURCHASE AS STATED IN THE DURATION. If this product is used for commercial,

industrial or rental purposes, the warranty will apply for ninety (90) days from the date of purchase. Some States

do not allow limitation on how long an implied warranty lasts, so the above limitations may not apply to you.

B. ANY INCIDENTAL, INDIRECT, OR CONSEQUENTIAL LOSS, DAMAGE, OR EXPENSE THAT MAY RESULT FROM ANY

DEFECT, FAILURE, OR MALFUNCTION OF THE CAMPBELL HAUSFELD PRODUCT. Some States do not allow the

exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply

to you.

C. Any failure that results from an accident, purchaser’s abuse, neglect or failure to operate products in accordance

with instructions provided in the owner’s manual(s) supplied with product. Accident, purchaser's abuse, neglect or

failure to operate products in accordance with instructions shall also include the removal or alteration of any safety

devices. If such safety devices are removed or altered, this warranty is void.

D. Normal adjustments which are explained in the owner’s manual(s) provided with the product.

E. Items or service that are normally required to maintain the product, i.e. o-rings, springs, bumpers, debris shields,

driver blades, fuses, batteries, gaskets, packings or seals, fluid nozzles, needles, sandblast nozzles, lubricants,

material hoses, filter elements, motor vanes, abrasives, blades, cut-off wheels, chisels, chisel retainers, cutters,

collets, chucks, rivet jaws, screw driver bits, sanding pads, back-up pads, impact mechanism, or any other

expendable part not specifically listed. These items will only be covered for ninety (90) days from date of original

purchase. Underlined items are warranted for defects in material and workmanship only.

F. Cosmetic defects that do not interfere with the product’s function.

7. RESPONSIBILITIES OF WARRANTOR UNDER THIS WARRANTY: Repair or replace, at Warrantor’s option, products or

components which are defective, have malfunctioned and/or failed to conform within duration of the warranty period.

8. RESPONSIBILITIES OF PURCHASER UNDER THIS WARRANTY:

A. Provide dated proof of purchase and maintenance records.

B. Call Campbell Hausfeld (800-543-6400) to obtain your warranty service options. Freight costs must be borne by the

purchaser.

C. Use reasonable care in the operation and maintenance of the products as described in the owner’s manual(s).

9. WHEN WARRANTOR WILL PERFORM REPAIR OR REPLACEMENT UNDER THIS WARRANTY: Repair or replacement will be

scheduled and serviced according to the normal work flow at the servicing location, and depending on the availability

of replacement parts.

This Limited Warranty applies in the United States, Canada and Mexico only and gives you specific legal rights. You may

also have other rights which vary from state to state or country to country.

Model IFN35650

Operating Instructions

www.chpower.com

Notes

Model IFN35650

Operating Instructions

www.chpower.com

Cesser d’utiliser tout outil s’il y a

malaise, engourdissement,

fourmillement ou douleur et consulter

un médecin.

Ce manuel contient des informations

concernant la sécurité, le

fonctionnement et l’entretien.

Lire attentivement ce

manuel et comprendre tous

les avertissements de

sécurité et les instructions

avant d’utiliser la cloueuse.

Si vous avez des questions,

contacter un représentant de

Campbell Hausfeld.

RESPONSABILITÉ DE L’UTILISATEUR

Avant d’utiliser cette cloueuse, prendre

connaissance de tous les avertissements

et des étiquettes concernant la

sécurité. Suivre les instructions données

dans ce manuel.

RESPONSABILITÉ DE L’EMPLOYEUR

Ce manuel d’instruction doit être mis à

la disposition de tous les utilisateurs

avant qu’ils ne se servent de la

cloueuse. S’assurer que tous les

utilisateurs lisent et comprennent

parfaitement les notices de sécurité,

étiquettes et instructions décrites dans

ce manuel.

Danger

Danger indique une situation

hasardeuse imminente qui RÉSULTERA

en perte de vie ou blessures graves.

• Ne pas utiliser un gaz

inflammable ni

l’oxygène pour

alimenter la cloueuse.

Utilisez seulement de

l’air comprimé filtré,

lubrifié et réglé.

L’utilisation d’un gaz comprimé au

lieu de l’air comprimé peut faire

exploser la cloueuse et entraîner

des blessures graves ou mortelles.

DANGER

Description

Cette cloueuse est conçue pour

boiseries, moulures intérieures,

plinthes, panneaux et armoires.

Caractéristiques: chargement facile du

magasin par l’arrière, capacité de 100

clous, embout ne laissant pas de

marque, éjection réglable, gâchette à

un coup, buse à dégagement rapide,

réglage de pénétration des clous.

Généralités Sur La

Sécurité

PROPOSITION 65 CALIFORNIE

Vous pouvez créer de la

poussière en coupant,

ponçant, perçant ou meulant

les matériaux tels que le bois, la

peinture, le métal, le béton, le ciment

ou autre maçonnerie. Cette poussière

contient souvent des produits

chimiques reconnus pour causer le

cancer, les déformations congénitales

ou autres problèmes de la

reproduction. Portez de l’équipement

de protection.

Toute

exposition excessive aux vibrations, tout

travail dans des positions incommodes et

tous déplacements à répétition peuvent

causer des blessures aux mains et aux

bras.

• Ne pas dépasser la

pression de service

maximale de la

cloueuse (827 kPa).

La cloueuse ne

fonctionnera pas

correctement. Ne pas

utiliser une source d’air comprimé

qui a une capacité de plus que 1379

kPa. La cloueuse pourrait exploser et

causer des blessures graves ou

mortelles.

• Ne jamais utiliser de

l’essence ni les fluides

inflammables pour le

nettoyage de la

cloueuse. Ne

jamais utiliser la

cloueuse près d’un liquide ou gaz

inflammable. Une étincelle peut

allumer les vapeurs et causer une

explosion qui peut résulter en perte

de vie ou blessures graves

personnelles.

MANUAL

OCO

827 kPa

Max.

Modèle IFN35650

IN725300AV 2/08

Les Cloueuses Campbell Hausfeld conforment aux/ou dépassent les standards de l’American National

Standard/International Staple, Nail and Tool Association in ANSI/ISANTA SNT-101-2002.

Table Des Matières

Directives De Sécurité . . . . . . . . 9 -11

Spécifications . . . . . . . . . . . . . . . . . 10

Modes De Fonctionnement . . . . . 12

Fonctionnement De

La Cloueuse . . . . . . . . . . . . . . . 11-13

Guide De Dépannage . . . . . . . . . . 14

Garantie . . . . . . . . . . . . . . . . . . . . . 15

Trouver le numéro de modèle et le

code date sur le chargeur de l’outil

et inscrire plus bas:

Nº du Modèle ___________________

Code de date ____________________

Conserver ces numéros

comme référence.

Cloueuse À Angle

Pour Finition

Instructions D’Utilisation Modèle IFN35650

S’il vous plaît lire et conserver ces instructions. Lire attentivement avant de monter, installer, utiliser ou de procéder à l’entretien du produit

décrit. Se protéger ainsi que les autres en observant toutes les instructions de sécurité, sinon, il y a risque de blessure et/ou dégâts matériels!

Conserver ces instructions comme référence.

Voir la Garantie à la page 15 pour de l’information importante sur l’utilisation commercial de ce produit.

MÉMENTO: Gardez votre preuve datée d'achat à fin de la garantie!

Joignez-la à ce manuel ou classez-la dans un dossier pour plus de sécurité.

9Fr

Généralités Sur La

Sécurité (Suite)

• Toujours bien

s’équilibrer

pendant la

manipulation ou

l’utilisation de la

cloueuse.

• Ne jamais modifier

ou empêcher le

fonctionnement

du mécanisme de

déclenchement par

contact (WCE) et ne

jamais maintenir la

gâchette enfoncée à l’aide de ruban

adhésif par exemple. Ceci pourrait

entraîner des blessures graves ou

mortelles.

• Ne toucher à la

gâchette qu’au

moment de poser

des clous. Ne jamais

actionner la gâchette

durant le transport

de la cloueuse ou

durant le raccordement de celle-ci au

tuyau d’air comprimé. L’éjection

accidentelle d’un clou peut causer

des blessures graves ou mortelles.

Avertissment indique une situation

hasardeuse potentielle qui PEUT résulter

en perte de vie ou blessures graves.

•

Toujours débrancher le

tuyau d’air comprimé

de la cloueuse avant

de dégager un clou

bloqué, de régler, de

réparer ou de transporter la cloueuse

ou lorsque celle-ci n’est pas en service.

AVERTISSEMENT

Le raccordement du tuyau d’air

comprimé doit toujours s’effectuer

AVANT le chargement du magasin.

L’éjection accidentelle d’un clou peut

causer des blessures graves ou mortelles.

•

Protéger vos yeux avec

des lunettes de sécurité

Z87 à écrans latéraux et

vos oreilles avec un

protecteur auditif. Le

patron et l’utilisateur sont

responsables pour assurer que

l’utilisateur et ceux à proximité de la

cloueuse portent l’équipement de

securite, sinon, il y a risque de

blessures graves oculaires ou de

dommage permanent a l’ouie. sécurité,

sinon, il y a risque de blessures graves

oculaires l’équipement de sécurité,

sinon, il y a risque de blessures graves

oculaires ou de dommage permanent à

l’ouie. sécurité, sinon, il y a risque de

blessures graves oculaires ou de

dommage permanent à l’ouïe.

•

Ne pas utiliser

un clapet ni

autre raccord

qui permet que

l’air reste dans

la cloueuse.

Cela peut

entraîner des blessures graves ou

mortelles.

• Ne jamais poser

l’embout de

clouage sur la

main ou sur toute

autre partie du

corps. L’éjection

accidentelle d’un

clou peut causer des blessures

graves ou mortelles.

• Ne jamais

transporter la

cloueuse par le

tuyau à air. Ne

jamais tirer sur le

tuyau pour

déplacer la

cloueuse ou le compresseur.

Garder le tuyau à air à l’écart de la

chaleur, l’huile et les objets pointus.

Remplacer les tuyaux endommagés,

faibles ou usés. Sinon, il y a risque

de blessures personnelles ou de

dommage à l’outil.

• Toujours présumer que la cloueuse

contient des clous. Ne jamais traiter

la cloueuse de jouet. Toujours tenir

les autres personnes à l’écart de

l’endroit de travaille en cas

d’expulsion accidentelle. Ne jamais

diriger la cloueuse vers une autre

personne. Le déclenchement

accidentel de la cloueuse peut causer

la mort ou blessures graves.

•

Ne jamais enfoncer

les clous un par

dessus l’autre. Le

clou pourrait

ricocher et causer

la mort ou une

blessure grave de perforation.

• Ne pas utiliser

la cloueuse/ni

permettre

qu’une autre

personne

l’utilise si les

avertissements

ou les étiquettes d’avertissement

situés sur le chargeur et corps de

la cloueuse ne sont pas lisables.

Loquet de

dégagement

rapide

Buse en

caoutchouc

non-gâchable Endroit d’expulsion des clous

Gâchette

Endroit de

chargement

de clous

Déflecteur d’échappement

orientable

• EXIGE: 0,05 m3/min avec 10 clous

par minute à 621 kPa

• PRISE D’AIR: 1/4 po NPT

• TAILLES DE CLOUS:

1-1/2 po à 2-1/2 po

• CAPACITÉ DU CHARGEUR:

100 Clous par charge, calibre 15

• POIDS: 2,27 kg, 311,9 g

• LONGUEUR: 13-3/4 po

• HAUTEUR: 12-1/4 po

• PRESSION MAXIMALE: 827 kPa

• GAMME DE PRESSION:

483 - 827 kPa

Pièces Détachées et Spécifications

de la Cloueuse

Chargeur d’aluminium

anodisé et durci

Décalque

d’avertissement

trilingue

Décalque de

spécifications

Montage de

poussoir de clous

Contrôle de

profondeur réglable

10 Fr

Modèle IFN35650

Instructions D’Utilisation

!AVERTISSEMENT

Inhaltsverzeichnis

Sprachen:

Andere Campbell Hausfeld Nagelpistole Handbücher

Campbell Hausfeld

Campbell Hausfeld IN727900AV Service-Handbuch

Campbell Hausfeld

Campbell Hausfeld NB0050 Bedienungsanleitung

Campbell Hausfeld

Campbell Hausfeld CHN101 Bedienungsanleitung

Campbell Hausfeld

Campbell Hausfeld CHN71500 Kurzanleitung

Campbell Hausfeld

Campbell Hausfeld CHN70800 Kurzanleitung

Campbell Hausfeld

Campbell Hausfeld SB3232 Bedienungsanleitung

Campbell Hausfeld

Campbell Hausfeld IN704700AV Bedienungsanleitung

Campbell Hausfeld

Campbell Hausfeld IronForce IFN219000 Handbuch

Campbell Hausfeld

Campbell Hausfeld CHN10401 Bedienungsanleitung

Campbell Hausfeld

Campbell Hausfeld Brad Nailer CHN70200 Kurzanleitung

Campbell Hausfeld

Campbell Hausfeld IN715401AV Bedienungsanleitung

Campbell Hausfeld

Campbell Hausfeld NB006401 Bedienungsanleitung

Campbell Hausfeld

Campbell Hausfeld NB0064 Bedienungsanleitung

Campbell Hausfeld

Campbell Hausfeld NB0040 Bedienungsanleitung

Campbell Hausfeld

Campbell Hausfeld CHN20103 Bedienungsanleitung

Campbell Hausfeld

Campbell Hausfeld JB004250 Bedienungsanleitung

Campbell Hausfeld

Campbell Hausfeld CHN70700 Service-Handbuch

Campbell Hausfeld

Campbell Hausfeld IN734600AV Bedienungsanleitung

Campbell Hausfeld

Campbell Hausfeld CHN90498 Bedienungsanleitung

Campbell Hausfeld

Campbell Hausfeld Brad Nailer CHN70200 Service-Handbuch

Campbell Hausfeld

Campbell Hausfeld SB504000 Bedienungsanleitung

Campbell Hausfeld

Campbell Hausfeld NS289100 Bedienungsanleitung

Campbell Hausfeld

Campbell Hausfeld Air Powered Flooring Nailer / Stapler... Service-Handbuch

Campbell Hausfeld

Campbell Hausfeld IFN10400 Bedienungsanleitung

Beliebte Nagelpistole Handbücher anderer Marken

Performance Tool

Performance Tool M643 Bedienungsanleitung

Hitachi

Hitachi VH650 - Fencing Nailer, Full Head Bedienungsanleitung

Parkside

Parkside PET 25 B1 Bedienungsanleitung

Senco

Senco Fusion Technology F-35XP Bedienungsanleitung

Grizzly

Grizzly G1847 Bedienungsanleitung

Ryobi

Ryobi R18N18G Bedienungsanleitung

Black & Decker

Black & Decker 492848-00 Bedienungsanleitung

HOLZMANN MASCHINEN

HOLZMANN MASCHINEN TN90 Bedienungsanleitung

Metabo HPT

Metabo HPT NR 3690DC Bedienungsanleitung

Surtek

Surtek CN650 Abmessungen und Installationsanleitung

Makita

Makita GF600 Bedienungsanleitung

Parkside

Parkside PET 25 B1 Bedienungsanleitung

Senco

Senco AirFree 25 Bedienungsanleitung

Freeman

Freeman P50LSLW Bedienungsanleitung

Aicon PRO

Aicon PRO DAC4507 Bedienungsanleitung

Makita

Makita AN923 Bedienungsanleitung

Grizzly

Grizzly T20644 Bedienungsanleitung

Black & Decker

Black & Decker 90514937 Bedienungsanleitung