Canarm PACIFIC WIND Bedienungsanleitung

03/10

INSTALLATION INSTRUCTIONS

PACIFIC WIND - ENERGY STAR

NOTE: FOR OPTIMUM QUIETNESS, FULLY ASSEMBLE FAN AND RUN FOR 24 HOURS

QUESTIONS OR CONCERNS CONTACT CANARM AT:

1-800-265-1833 (ENGLISH)

1-800-567-2513 (FRENCH)

Monday through Friday 8:00 a.m. to 5:00 p.m. EST

IMPORTANT

FOR YOUR RECORDS, RECORD AND KEEP

THE FOLLOWING INFORMATION

Date of purchase:

Place of purchase:

Model on carton:

I.D.# (bottom of carton):

UPC (bottom of carton):

1. Turn off power at main electrical service box before starting installation.

2. Electrical connections must comply with local code ordinances or

national electrical codes.

3. Make sure the installation site you choose allows the fan blades to rotate

freely without any obstructions.

4. When mounting the fan on a ceiling outlet box, use a metal octagon box.

The outlet box and its support must be able to withstand the moving

weight of the fan (minimum of 35 lbs.).

SAFETY PRECAUTIONS

TOOLS AND MATERIALS REQUIRED

Adjustable wrench

Phillips screwdriver

Blade screw driver

Step ladder

Wire cutters

Wiring supplies as required

• to reduce the risk of personal injury NO NOT bend the blade brackets

when installing the brackets, balancing the blades or cleaning the fan.

Also, NO NOT insert foreign objests in between rotating fan blades.

• mount only to an outlet box marked acceptable for fan support

• mount with the lowest moving parts at least 2.1 meters (6.9 feet) above

oor grade level.

• NO NOT operate reversing switch while fan blades are in motion. Fan

must be turned off and rotating blades topped, reverse chain pull, the

speed chain pllled again to start in the opposite direction.

WARNING

pg. 2

pg. 3

ASSEMBLY DRAWING

1. wooden joist

2. metal outlet box (not provided)

3. ceiling

4. rubber gasket

5. mounting bracket

6. outlet box screws

7. wood screws & at washers

8. downrod

9. canopy

10. bolt

11. cotter pin

12. motor

13. blade bracket screw

14. bre washer

15. blade

16. rubber washer

17. blade bracket

18. lock washer

19. motor screw

20. switch housing

NOTE: Item #16 is only supplied on fans with high gloss blades

1110

18 17 16

14 15

WITH DOWNROD

pg. 4

• obtain fan motor

• remove cotter pin and bolt from yoke

• loosen jam screw in yoke until it is ush with the inside surface

• obtain dowrod and canopy (and yoke cover - optional)

• place downrod inside canopy (and yoke cover - optional)

• route wires and safety cable exiting motor through canopy and downrod

• insert bolt through hole in shaft and downrod

*be careful not to damage or cut the fan wires

• secure bolt with cotter pin

• secure downrod in position by tightening jam screws and lock nut

• place glass motor housing onto motor top

• slide yoke cover (optional) over yoke

1. MOUNTING

*NOTE: all set screws must be checked and re-tightened where

necessary after installation.

INSTALLATION

DOWNROD MOUNT

jam screw

lock nut

motor

yoke cover

(optional)

jam screw

yokecotter pin bolt

yoke

jam

screw

pg. 5

• secure rubber gasket and mounting bracket to metal outlet box using

outlet box screws

• secure once more by placing two wood screws and at washers (supplied)

through outer slots of mounting bracket and into the wood joist. Leave one

of the wood screws sufciently loose to allow the safety cable to be looped

around before nal tightening.

2. INSTALL MOUNTING BRACKET

INSTALLATION

wood screws &

at washers

outlet box

screws

mounting

bracket

rubber gasket

metal outlet box

wood joist

ceiling

pg. 6

• obtain fan and place hemisphere of downrod into mounting bracket

• rotate fan until the slot in the hemisphere locks into the tab of the

mounting bracket

• place looped end of safety cable over the wood screw and at washer

not previously tightened (in Step 3)

• tighten above wood screw securing the safety cable

3. HOOKING UP SAFETY CABLE (DOWNROD MOUNT)

safety

cable

hemisphere

mounting

bracket

tab

slot

hemisphere

safety

cable

mounting

bracket

INSTALLATION

pg. 7

There are several different wiring combinations that can be used in controlling

your ceilingfan to meet your specic requirements. Should the following method

not meet your requirements call or visit your nearest Canarm distributor for a full

list of fan accessories.

4. ELECTRICAL HOOKUP

INSTALLATION

NOTE: Once ground wires are connected, carefully tuck wires and marrette into

the metal outlet box making sure that the wires are clear of the hemisphere and

downrod when positioning in the mounting bracket.

A. CONNECTING THE GROUND WIRE (GREEN)

CAUTION

GREEN wire - GROUND

BLACK wire (fan) - POWER

WHITE wire (fan) - COMMON

RED/BLUE wire (light kit) - POWER

See SAFETY PRECAUTIONS

on page 2 before wiring

pg. 8

INSTALLATION

B. CONNECTING BLACK, WHITE & (BLUE OR RED) WIRES

4. ELECTRICAL HOOKUP (CONTINUED)

• connect white wire from outlet box to white wire from fan using marrette (not supplied).

• connect black wire from outlet box to black wire from fan plus (red or blue wire)

using a marrette.

NOTE: A red or blue wire would be power for a light kit if applicable.

NOTE: Once ground wires are connected, carefully tuck wires and marrette into the

metal outlet box making sure that the wires are clear of the hemisphere and downrod

when positioning in the mounting bracket.

white

ground

blue/red

black

pg. 9

5. MOUNTING FAN ASSEMBLY

INSTALLATION

• loosen two screws and washers (B) on mounting bracket which correspond

with the slots in the canopy

• remove two screws and washers (A) on the mounting bracket which

correspond with the oblong holes in the canopy.

• position the canopy to the mounting bracket, aligning slots to the screws (B)

then twist to lock

• position and tighten two screws and washers (A) then tighten the two screws (B)

pg. 10

6. MOUNTING BLADE BRACKETS TO BLADES

INSTALLATION

A. “DIECAST” BLADE BRACKETS

• obtain hardware package containing blade bracket screws and washers.

• place bre washer over screw.

• place screw through blade hole and slip a rubber washer over the screw.

• align screw with blade bracket and secure.

• repeat for other two screws.

• once all blade brackets are attached to blades double check that screws are tight.

NOTE: Rubber washers only supplied on those fans with high gloss blades

B. “MEDALLION STYLE” BLADE BRACKETS

• obtain hardware package containing blade bracket screws and washers.

• place bre washer over screw.

• place rubber washers in holes of blades.

• position bottom blade bracket and top blade bracket with blade.

• start screws and bre washers by placing into top blade bracket and blade

and threading into the bottom bracket.

• tighten screws only after the 3 screws have been started and blade brackets

are straight on the blades.

blade bracket screw

blade bracket

blade

bre washer

rubber washer

bre washer

blade bracket screw

blade

bottom

blade bracket

top

blade bracket

rubber washer

Inhaltsverzeichnis

Andere Canarm Lüfter Handbücher

Canarm

Canarm SKYLAR Bedienungsanleitung

Canarm

Canarm BPT18-34A-1 Stücklistenhandbuch

Canarm

Canarm UF08-W Bedienungsanleitung

Canarm

Canarm CA20AG-FVD1 Bedienungsanleitung

Canarm

Canarm DUAL MOUNT series Bedienungsanleitung

Canarm

Canarm AgSystems MAX-AIR PLUS Bedienungsanleitung

Canarm

Canarm Tri-Lite 3LMPEC Bedienungsanleitung

Canarm

Canarm XB Bedienungsanleitung

Canarm

Canarm 3000M Series Bedienungsanleitung

Canarm

Canarm XFS10 Bedienungsanleitung

Canarm

Canarm GSF Series Bedienungsanleitung

Canarm

Canarm BPT12-13H Stücklistenhandbuch

Canarm

Canarm 700 Series Bedienungsanleitung

Canarm

Canarm AgSystems PF52 Bedienungsanleitung

Canarm

Canarm HUGGER STYLE Series Bedienungsanleitung

Canarm

Canarm PALISADE Bedienungsanleitung

Canarm

Canarm BUILDER Bedienungsanleitung

Canarm

Canarm PLF09 Bedienungsanleitung

Canarm

Canarm XB Bedienungsanleitung

Canarm

Canarm DUAL MOUNT SERIES Bedienungsanleitung

Canarm

Canarm 3LEC Series Bedienungsanleitung

Canarm

Canarm HVR Bedienungsanleitung

Canarm

Canarm FGI18 Bedienungsanleitung

Canarm

Canarm SD08-EC Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Hinkley

Hinkley HIGHLAND Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung