Cannon Tools NEILSEN CT4887 Bedienungsanleitung
AIR POWERED CV BOOT INSTALLATION TOOL
CT4887
INSTRUCTIONS
Cannon Tools Limited
Address: 20 Station Road, Rowley Regis, West Midlands, B65 0JU.U.K.
SAVE THESE INSTRUCTIONS AND PRECAUTIONS.
EC DECLARATION OF CONFORMITY
We CANNON TOOLS LTD
20 Station road, Rowley Regis, West Midlands,B65 0JU.U.K.
Declare that the following machine complies with the appropriate basic safety
and health requirements of the EC Directive based on its design and type, as
brought into circulation by us.
In case of alteration of the machine, not agreed upon by us, this declaration will
lose its validity.
Product description: AIR POWERED CV BOOT INSTALLATION TOOL
Model: CT4887
Applicable EC Directives:
EC Machinery Directive 2006/42/EC
Harmonized standards
EN ISO 12100：2010
20 Station Road, Rowley Regis, West Midlands, B65 0JU.U.K.
Mr. Gurcharan Tony Singh Sanghera
Managing Director
CANNON TOOLS LTD
2021-01-26
SPECIFICATIONS
Working pressure: 72-130Psi
Dimensions: 460 x 140 x 140mm
Maximum joint diameter 120mm
The CV boot installation tool is to be used solely for the stretching of flexible CV boots onto
drive-shaft assemblies of automotive vehicles.
SAFETY FIRST
Read the operating and safety instructions. Follow them carefully. Maximum safe operating
pressure 130 psi. Air lines are dangerous – use them correctly.Keep hands away from moving
parts. Never operate the CV boot installation tool near the face or body. Only use this tool to fit
CV boots. If air line pressure exceeds 130 psi, fit a regulator. Disconnect the CV boot
installation tool from the air supply after use.
PUTTING INTO SERVICE
Before use, check cap-retaining screws are secure. If the CV boot installation tool is dropped,
check for cracked components. Check air line pressure before connecting the Boot gun. The
CV boot installation tool should be used only by people trained in the use of pneumatically
operated tools.
ASSEMBLY / DISMANTLING
No assembly or dismantling is required. The air adaptor may be exchanged if necessary.
The body is threaded to accept 1/4 inch BSP connector.
AIR SUPPLY
To prevent explosion: Use only clean, dry, regulated, compressed air to power this tool. Do not
use oxygen, carbon dioxide, combustible gases, or any other bottled gas as a power source
for this tool.
OPERATION
1. Slide boot onto arms, large end first. The arms
should just protrude from the small end of the boot.
To fit a boot to an inner joint, turn the boot inside out
before sliding it onto the CV boot installation tool’s
arms.
2. Press “+” button until arms open enough to pass
over the joint. Keep hands clear of moving parts.
3. The air line can now be disconnected. The arms
will remain open until the Minus button is pressed.
4. Place this tool over CV joint and press release
Minus button . Keep hands away from moving parts.
5. Slide the boot from this tool onto the axle and
withdraw the CV boot installation tool over the joint,
leaving the boot in position. Complete the
installation in the normal way.
Maintenance
Do not attempt to clean or repair the CV boot installation tool whilst air line is connected.
There is no routine maintenance on this tool. Only use genuine spare parts obtainable from
your supplier.
SYMBOLS
In this manual and/or on the machine the following symbols are used:
DISPOSAL
At the end of the machine's working life, or when it can no longer be repaired, ensure that it is
disposed of according to national regulations.
Contact your local authority for details of collection schemes in your area.
In all circumstances:
Do not dispose of this tool with domestic waste.
Do not incinerate.
During decommissioning of the equipment, certain hazards should be understood and
avoided:
. Only with the line pressure released shall the equipment be
disassembled.
.Goggles should be worn.
Denotes risk of personal injury, loss of life or damage to the tool in
case of non-observance of the instructions in this manual.
Wear hearing protection.
Wear safety goggles.
Contact with or inhalation of dust coming free during use (e.g.
lead-painted surfaces, wood and metal) can endanger your health
and the health of bystanders. Always wear appropriate protective
equipment, such as a dust mask. Always use proper dust
extraction during use.
Wear gloves.
CANNON TOOLS LTD
Add: 20 station road, Rowley Regis, west midlands,B65 0JU.U.K.
Made in China
Inhaltsverzeichnis
Andere Cannon Tools Werkzeuge Handbücher
