Canon ImageCLASS MF4690 Sicherheitsleitfaden
ENG
Starter Guide
Please read this guide before operating this product.
After you finish reading this guide, store it in a safe place for future reference.
Set Up the Machine
Unpacking the Machine Before Setting Up the Machine
●Remove all shipping tape and packing material from the machine. ●When moving the machine, grip the handles on
both left and right sides of the machine and lift it
carefully, as shown in the illustration right.
●The shapes of your machine and supplies may
differ slightly from those illustrations listed in this
manual.
1 2
3
Do You Have Everything?
Manuals for the Machine
●Starter Guide (This Document): Machine set-up and software installation
●Basic Operation Guide: Basic features, maintenance, machine settings, and specifications
●Reference Guide (located on the User Software CD): Advanced features, system monitor, and
reports and lists
●Scanner Driver Guide (located on the User Software CD): Scanner settings from a computer
●Machine ●Document Feeder Tray ●Power Cord ●Destination Labels●Telephone Cable
●Dust Cover ●Paper Cassette ●Toner Cartridge
●Starter Guide (This Document)
●Basic Operation Guide
●User Software CD
●Reference Guide (located on User
Software CD)
●Scanner Driver Guide (located on
User Software CD)
●Limited Warranty Notice
●Registration Card
4
5
Install Toner Cartridge
1
Remove the toner cartridge from the bag.
Keep the bag for future use. CAUTION
Do not open the drum protective shutter (A).
2
Gently rock the toner cartridge several times to
distribute toner inside.
3
Pull the seal completely out.
NOTE
Do not pull the seal out at an angle.
4
Lift the scanning platform (A) until it is locked. (You
will hear an audible “click.”)
5
Open the toner cover (B), using the tab (A) which
covers over on dent.
6
Hold the toner cartridge by its handle (A).
7
Insert the cartridge so that the protrusion on the
right side of the toner cartridge (A) fits into the
guide (B) located on the right side of the machine
and slide it down parallel to the guide.
8
Push the toner cartridge to make sure it is properly
set in the machine.
9
Close the toner cover using the tab.
10
Close the scanning platform.
CAUTION
– Be careful not to get your fingers caught.
– If you cannot close the toner cover, do not force it to
close. Open the cover and make sure the toner
cartridge is properly set in the machine.
A
AA
B
A
6
7
Set Up the Paper Cassette and Load Paper
1
Align the guides (B) on the both edges of the
paper cassette to the protrusions (A) inside the
machine.
NOTE
Install the paper cassette with the front end tilted
upwards.
2
Push the paper cassette down until the hooks (A)
on both sides of the paper cassette engage the
protrusions (B) inside the machine.
3
Open the front panel of the paper cassette.
4
Slide the paper guide rail (A), and then pinch and
slide the side paper guides (B) to match the size of
paper.
5
Fan the paper stack and even the edges.
6
Load the paper into the paper cassette with the
print side up. Make sure the paper stack sits below
the small fin (A) on the side paper guide.
7
Adjust the paper guide rail to match the size of
paper.
AA
B
B
BB
AA
8
9
8
Close the front panel of the paper cassette. NOTE
To load Legal-size paper, leave the front panel of
paper cassette open and adjust the paper guide rail
(A) for Legal-size paper.
9
Connect the edge of dust cover (A) and the edge of
paper cassette (B).
10
Slide the output tray extension on the front of the
machine, and lift the paper stopper.
11
Attach the document feeder tray on the document
feeder.
NOTE
– The default paper size/type setting is <LTR> and
<PLAIN PAPER>. When you load other size and/or
type of paper, change the paper size/type setting. For
details, see Chapter 2, “Document and Paper,” in the
Basic Operation Guide.
– For loading paper in the multi-purpose tray, see
Chapter 2, “Document and Paper,” in the Basic
Operation Guide.
A
B
A
B
10
11
Connect the Power Cord and Turn On the Machine Connect Telephone Cables
12
Connect your external telephone to the external device jack (A) on back side of the machine if required.
Connect the supplied telephone cable to the telephone line jack (B) on back side of the machine and the wall jack.
NOTE
If you want to use an external telephone and receive faxes, you will need to set up the receiving mode. (See “Set the Machine for
Receiving Faxes,” on p. 19.)
Connect the power cord into the rear socket on the
back side of the machine and the wall outlet, and
press the [I] side of the main power switch to ON.
The machine enters the standby mode.
What if...
●<TONER COVER OPEN/CLOSE COVER> is displayed:
Make sure that the toner cover and scanning platform are closed properly. (See “Install Toner Cartridge,” on p. 5.)
●<TONER IS NOT SET/INSERT TONER> is displayed:
Make sure that the toner cartridge is installed properly. (See “Install Toner Cartridge,” on p. 5.)
●<LOAD PAPER/CASSETTE :LTR> is displayed:
Make sure that paper is loaded in the machine. (See “Set Up the Paper Cassette and Load Paper,” on p. 7.)
Main power switch
100% LTR
TEXT/PHOTO 01
Ex.
A
B
12
13
Set the Date and Time Set the Telephone Line Type
●Entering Information
– Numeric keys: Enters numbers.
– [ ] or [ ]: Moves the
cursor position.
– [OK]: Confirms the entry.
1Press [Additional
Functions].
2Press [ ] or [ ] to
select <5. TX/RX
SETTINGS>, then press
[OK].
3Press[]or[]to
select <2. FAX
SETTINGS>, then press
[OK].
4Press[]or[]to
select <2. USER
SETTINGS>, then press
[OK].
5Press [ ] or [ ] to
select <2. TEL LINE
TYPE>, then press [OK].
6Press[]or[]to
select the telephone line
type, then press [OK].
<TOUCH TONE>: Tone dialing
(default)
<ROTARY PULSE>: Pulse dialing
1Press [Additional
Functions].
2Press[]or[]to
select <8. TIMER
SETTINGS>, then press
[OK].
3Press [ ] or [ ] to
select <1. DATE&TIME
SETTING>, then press
[OK]. 7Press [Stop/Reset] to
return to the standby
mode.
4Use the numeric keys to
enter the date (month/day/
year) and time (in 24-hour/
military time format), then
press [OK].
5Press [Stop/Reset] to
return to the standby
mode.
NOTE
– You can select the date format
among three types listed below at
<3. DATE TYPE SELECT>.
– <MM/DD/YYYY>
– <DD/MM YYYY>
– <YYYY MM/DD>
– By default, <6. DAYLIGHT
SV.TIME> in the <8. TIMER
SETTINGS> menu is set to <ON>.
If you want to set <6. DAYLIGHT
SV.TIME> in the <8. TIMER
SETTINGS> menu to <OFF>, see
Chapter 1, “Before Using the
Machine,” in the Basic Operation
Guide.
[OK]
Numeric
Keys
[]
[] [Stop/Reset]
[Additional
Functions]
Ex.
DATE&TIME SETTING
12/31/´07 23:19
14
15
Set the Machine for Sending Faxes
Guidelines for Entering Information
The sender information you register in the machine appears in the header of each page received by your
recipient.
NOTE
Before sending a fax, you MUST register your fax number, unit name, and the current date and time in the machine.
Entering Information
Use the following keys to enter information in the machine.
You can enter the following characters in each input mode:
●Use the numeric keys to enter characters.
Press the numeric key repeatedly until the
required character appears.
●Press [#] to enter symbols.
●Press [ ] to switch among input modes:
– [:a]: Letter mode
– [:1]: Number mode
●Press [ ] to move the cursor position
right.
●Press [Clear] or [ ] to delete the
character before the cursor position. Hold
[Clear] to delete the entire entry.
Pressing [ ] and [Clear] for entering the
unit name moves the cursor left and deletes
the character at the position.
●Press [OK] to confirm the entry.
CANON 0001/0001
12/31 2007 10:50 FAX 123XXXXXXX
Date and time
Fax/telephone
number
Unit name Page number/
Number of pages
:a :1
[1] @.-_/ 1
[2] abcABC 2
[3] defDEF 3
[4] ghiGHI 4
[5] jklJKL 5
[6] mnoMNO 6
[7] pqrsPQRS 7
[8] tuvTUV 8
[9] wxyzWXYZ 9
[0] 0
[ ]
[#] – . # ! " , ; : ^ _ = / | ’ ? $
:a :1
@ % & + \ ( ) [ ] { } < >
[] [#]
[OK] [Clear] Numeric
Keys
[]
[] [Stop/Reset]
[Additional
Functions]
16
17
Register Sender Information
1Press [Additional
Functions].
2Press[]or[]to
select <5. TX/RX
SETTINGS>, then press
[OK].
3Press [ ] or [ ] to
select <2. FAX
SETTINGS>, then press
[OK].
4Press[]or[]to
select <2. USER
SETTINGS>, then press
[OK].
5Press [ ] or [ ] to
select <1. UNIT
TELEPHONE #>, then
press [OK].
6Use the numeric keys to
enter your fax/telephone
number (max. 20 digits,
including spaces), then
press [OK].
7Press [Additional
Functions] twice.
8Press[]or[]to
select <1. TX/RX
COMMON SET.>, then
press [OK].
9Press [ ] or [ ] to
select <1. TX
SETTINGS>, then press
[OK].
10 Press [ ] or [ ]
to select <1. UNIT
NAME>, then press
[OK].
11 Use the numeric keys to
enter the unit name (up
to 24 characters) (your
name, company name,
etc.), then press [OK].
12 Press [Stop/Reset] to
return to the standby
mode.
Ex.
UNIT TELEPHONE #
Ex.
UNIT NAME :a
18
Andere Handbücher für ImageCLASS MF4690
6
Inhaltsverzeichnis
Andere Canon Multifunktionsdrucker Handbücher
Canon
Canon iR1200 Series Bedienungsanleitung
Canon
Canon imageRUNNER C4080 SERIES Bedienungsanleitung
Canon
Canon 1238P Technisches Datenblatt
Canon
Canon LASER CLASS 710 Bedienungsanleitung
Canon
Canon MX720 Series Einrichtungshandbuch
Canon
Canon Pixma MG7100 Series Einrichtungshandbuch
Canon
Canon MultiPASS MP390 Bedienungsanleitung
Canon
Canon ImageCLASS MF4570dw Montageanleitung
Canon
Canon iR3300 Series Bedienungsanleitung
Canon
Canon CFX-L4500 IF Bedienungsanleitung
Canon
Canon ImageCLASS MF4690 Bedienungsanleitung
Canon
Canon PIXMA MG6120 Series Handbuch
Canon
Canon PIXMA MG5450 Bedienungsanleitung
Canon
Canon imageRUNNER ADVANCE 8105 Bedienungsanleitung
Canon
Canon Color imageRUNNER C3200 Bedienungsanleitung
Canon
Canon imageCLASS D860 Handbuch
Canon
Canon iR5075 Bedienungsanleitung
Canon
Canon FAX-L2000 Bedienungsanleitung
Canon
Canon 1238iF II Bedienungsanleitung
Canon
Canon iR3530 Referenzhandbuch
Beliebte Multifunktionsdrucker Handbücher anderer Marken
Triumph Adler
Triumph Adler DC 2016 Handbuch
Epson
Epson WorkForce WF-2510 Benutzerhandbuch
Epson
Epson Stylus Scan 2000 Installations- und Betriebshandbuch
Epson
Epson PictureMate Snap PM 240 Bedienungsanleitung
Konica Minolta
Konica Minolta bizhub C35 Bedienungsanleitung
Brother
Brother MFC-J430w Bedienungsanleitung
