Canon MultiPASS F30 Bedienungsanleitung

Step 1: Unpack the F30 MFP

1. Carefully remove all items from the box.

Step 2: Set up the F30 MFP

1. Remove shipping tape and protective shipping materials.

2. Open the scanning unit by pressing the Open button.

Remove the shipping material.

3. Unlock the scanner.

• Set the scanning lock to unlock.

• Press the scanning unit closed until it clicks.

4. Attach the trays:

Step 3: Prepare the F30 MFP

1. Connect the power cord and plug it into a socket.

2. If the F30 MFP does not power up when plugged in, press the ON/OFF button to turn it on.

3. Open the scanning unit again. The printhead holder will move to the center position.

IMPORTANT: Remove the tape on the printhead holder lever.

Step 4: Install the Printhead

1. Remove the printhead from its package.

2. Turn the printhead over, then remove the orange protective cap.

NOTE: Do not touch the electrical contacts.

3. Raise the gray lock lever.

4. Gently slide the printhead into the holder. The printhead will rest at a slight angle.

Do not press it down.

5. Lower the lock lever and gently press it down until it locks into place.

Step 5: Install the Ink Tanks

1. Pull the orange tab off the yellow ink tank (BCI-3eY), then remove and discard the plastic

wrapper.

2. Twist off and discard the orange protective cap.

NOTE: To avoid spilling ink, never press on the sides of the ink tank.

3. Insert the ink tank into the correct slot (refer to the color guide on the printhead).

Press down gently until the ink tank locks into place.

4. Insert the remaining three ink tanks into their assigned slots.

5. Press the scanning unit closed until it clicks.

Step 6: Align the Printhead

1. Place a stack of paper in the multi-purpose tray in preparation for printhead alignment.

2. Once the printhead has been installed ALIGN PRINTHEAD/PRESS SET KEY will display on the

LCD panel.

Press the key once.

3. The F30 MFP will print a vertical line pattern, and the LCD message will change to:.

4. Review the vertical pattern printout, noting which box in Column A prints with the most solid

image.

For the A Column printed pattern, use the key to scroll to the value for the most solid box

in the column.

NOTE: If you have difficulty on Column A when choosing between two patterns, use the larger

value number.

Press to select. CHANGE V VALUE will appear again, this time for Column B:

5. Repeat Step 4 for patterns B through F on the printout.

NOTE: if you have difficulty on Columns B or C when choosing between two patterns, use the larger value

number. If you have difficulty when choosing between patterns for Columns D, E or F, use the smaller

value number.

6. When values for all vertical columns on the printout have been entered, the LCD will display

LAT LINE PATTERN, and a lateral (horizontal) pattern will print.

Once the pattern has printed, the LCD message will change to:

7. Review the lateral pattern printout, noting which solid box in Column G on the printout has

the most solid image.

For the G column printed pattern, use the keys to scroll to the value with the most solid

box in the column.

NOTE: If you have difficulty on Column G when choosing between two patterns, use the smaller value

number.

Press to select.

8. Repeat Step 7 for Column H on the printout.

9. When printhead alignment is complete, the F30 MFP will return to standby mode.

Step 7: Install the Software (USB cable only)

NOTE: Windows 98, Me and 2000 only support the use of a USB cable.

IMPORTANT: DO NOT connect he F30 MFP to your computer until prompted, or the computer may

attempt to install the software before the unit is ready.

1. Turn the F30 MFP on if not on already.

Click CANCEL if you see a screen that says "New Hardware Found," "Update Device Driver Wizard," or

"Add New Hardware Wizard."

2. With your PC on, close any open application including virus checkers.

3. Insert the MultiPASS Suite Software CD-ROM into the CD-ROM drive. The setup program

should run automatically.

NOTE: If the setup program does not run, click START, then RUN, then type D:\csplash.exe, where D is

your CD-ROM drive.

4. When the main menu appears, click Install MultiPASS Suite.

5. Read the Welcome screen, then click Next.

6. Read the License Agreement. If you agree to its terms, click YES. If you do not agree, click

NO. You will not be allowed to continue the installation process.

7. Select the MultiPASS F30 for installation.

Continue to follow the on-screen instructions.

8. When prompted, connect one end of the USB cable (not included) to the computer and the

other end to the F30 MFP, so it can be automatically detected.

Once the USB cable is connected, if a system message appears indicating the system driver is being

installed, wait until the installation process in completed then click YES to continue.

9. Continue to follow on-screen instructions to complete the installation process.

10. When installation is complete, you will need to restart your PC before using the MultiPASS

Suite software. If your PC does not restart automatically, restart it manually.

NOTE: Remember to register your product to ensure product support. The serial number is located on the

back of the F30 MFP, above the parallel port.

Step 7: Install the Software (Parallel cable only)

NOTE: Windows 95, 98, Me, NT 4.0 and 2000 support the use of an IEEE 1284 parallel printer cable.

IMPORTANT: DO NOT connect he F30 MFP to your computer until prompted, or the computer may

attempt to install the software before the unit is ready.

1. Be sure both the F30 MFP and the PC are turned on before continuing…

2. Connect one end of a parallel cable (not included) to the computer, the other to the F30 MFP.

3. Turn on both the F30 MFP and your PC.

With your PC on, close any open applications, including virus checkers.

Click CANCEL if you see a screen that says "New Hardware Found," "Update Device Driver Wizard" or "Add

New Hardware Wizard."

4. Insert the MultiPASS Suite Software CD-ROM into the CD-ROM drive. The setup program

should run automatically.

NOTE: If the setup program does not run, click START, then RUN, then type D:\csplash.exe, where D is

your CD-ROM drive.

5. When the main menu appears, click Install MultiPASS Suite.

6. Read the Welcome screen, then click NEXT.

7. Read the License Agreement.

If you agree to its terms, click YES. If you do not agree, click NO. You will not be allowed to continue the

installation process.

8. Select the MultiPASS F30 for installation.

Continue to follow the on-screen instructions.

9. When installation is complete, you will need to restart your PC before using the MultiPASS

Suite software. If your PC does not restart automatically, restart it manually.

NOTE: Remember to register your product to ensure product support. The serial number is located on the

back of the F30 MFP, above the parallel port.

Andere Handbücher für MultiPASS F30

Andere Canon Multifunktionsdrucker Handbücher

Canon

Canon 1483B001 Bedienungsanleitung

Canon

Canon Laser Class 700 Series Montage- und Wartungsanleitung

Canon

Canon imageCLASS MP390 Bedienungsanleitung

Canon

Canon MultiPASS C3500 Bedienungsanleitung

Canon

Canon MP730 - MultiPASS Color Inkjet Handbuch

Canon

Canon 4204B019AA Bedienungsanleitung

Canon

Canon MF7280 - ImageCLASS B/W Laser Bedienungsanleitung

Canon

Canon 3743B002 Benutzerhandbuch

Canon

Canon C3000 - MultiPASS Color Inkjet Printer Bedienungsanleitung

Canon

Canon MP-C545 Bedienungsanleitung

Canon

Canon iR2020 Series Bedienungsanleitung

Canon

Canon 2184B002 Bedienungsanleitung

Canon

Canon MF7280 - ImageCLASS B/W Laser Bedienungsanleitung

Canon

Canon Color imageCLASS MF8050Cn Sicherheitsleitfaden

Canon

Canon PIXMA MP470 Bedienungsanleitung

Canon

Canon MultiPASS C545 Bedienungsanleitung

Canon

Canon ImageRunner 4051 Bedienungsanleitung

Canon

Canon PIXMA MX532 Series Bedienungsanleitung

Canon

Canon Color imageCLASS MF8350Cdn Sicherheitsleitfaden

Canon

Canon imageRUNNER ADVANCE DX C359i Bedienungsanleitung

Canon

Canon imageRUNNER C1030 Sicherheitsleitfaden

Canon

Canon mg6400 series Einrichtungshandbuch

Canon

Canon PIXMA MP600 Bedienungsanleitung

Canon

Canon imageRUNNER 5570 Bedienungsanleitung

Beliebte Multifunktionsdrucker Handbücher anderer Marken

Triumph Adler

Triumph Adler DC 2016 Handbuch

Epson

Epson WorkForce WF-2510 Benutzerhandbuch

Epson

Epson Stylus Scan 2000 Installations- und Betriebshandbuch

Epson

Epson PictureMate Snap PM 240 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub C35 Bedienungsanleitung

Brother

Brother MFC-J430w Bedienungsanleitung

Konica Minolta

Konica Minolta BIZHUB 558 Bedienungsanleitung

Lexmark

Lexmark MX710 Series Handbuch

Brother

Brother MFC-9760 Bedienungsanleitung

Lexmark

Lexmark XC8155 Bedienungsanleitung

Lexmark

Lexmark X642E Bedienungsanleitung

Sharp

Sharp MX-2310U Leitfaden

Aficio

Aficio 200 Bedienungsanleitung

Ricoh

Ricoh Pro C900 Bedienungsanleitung

Lexmark

Lexmark X925 Bedienungsanleitung

Brother

Brother Business Smart MFC-J4510dw Bedienungsanleitung

Epson

Epson Stylus CX8400 Series Bedienungsanleitung

Oce

Oce VarioLink 5022 Bedienungsanleitung