Canon ImagePASS-B2 Bedienungs- und Wartungshandbuch

ENGLISH 日本語

imagePASS-B2 Installation Procedure

imagePASS-B2 設置手順書

This installation procedure is written in Japanese and English. The installation procedure for Japan model is described in Japanese and one for the other modes is

described in English. These procedures are different from each other. Follow the procedure corresponding to the installed model.

- Japanese: The installation procedure for Japan model

- English: The installation procedure for the other models except for Japan model

この設置手順書には、和文と英文の設置手順が記載されている。和文では日本モデル用の設置手順が記載されており、英文では日本モデル以外のその他のモデル用の設

置手順が記載されている。それぞれの設置手順は異なっているので、モデルに応じた手順に従うこと。

・和文：日本モデル用設置手順

・英文：日本モデル以外のその他のモデル用設置手順

PRINTED IN USA 45110734 PUB No. FT1-0694-000

Check Items when Turning OFF the Main Power

How to Check this Installation Procedure

When Using the Parts Included in the Package

A symbol is described on the illustration in the case of using the parts included in the package

of this product.

Packaged Item

Symbols in the Illustration

The frequently-performed operations are described with symbols in this procedure.

Connector

Disconnect

Screw

Tighten Remove Connect Secure Free

Harness

Push

Insert Plug in Turn on

Sound CheckCheck Visual Check

Claw

Remove

Checking instruction

F-1-1

F-1-2

Before Connection

The IP addresses for communication between the host

machine and server are set automatically

1) Enter the Service Mode (level 1).

2) COPIER > OPTION > INT-FACE > IMGCONT> "3"

3) Exit the Service Mode

Securing space for installation

Secure a space to install this equipment as shown in the gure below. A space of 200mm or

more is required from the back of this equipment.

200mm or more

Rear

Equipment

Front

Check Items when Turning OFF the Main Power

Check that the main power switch is OFF.

1) Turn OFF the main power switch of the host machine.

2) Be sure that display in the Control Panel and the lamp of the main power supply are turned

off, then disconnect the power plug.

F-1-3

Installation Outline Drawing

Checking the Content

Europe x 2

USA x 1

[1] PS Unit X 1 [2] Mounting Plate X 1 [3] Support Plate X 2

[4] Power Cord [5] Cross Ethernet

Cable 0.5m X1

[6] Shield Ethernet

Cable 3.0m X1

[7] Interface Cable X 1 [8] Open I/F PCB X 1 [9] Screw (TP; M3x6) X 4

[10] Screw with Toothed

Washer

(Binding small; M4x8) X 8

[11] Stepped Screw (M4)

X 4

[12] Wire Saddle X 3

F-1-4

• [4] Power Cord

The connector has a different shape depending on locations.

2 are packaged in the products for EUR/1 is packaged in the products for USA

Use the correct power code to mach the location/area of installation.

Make sure not to leave unused power code at the site.

< CD/GUIDES >

• Media Pack US

Installation Outline Drawing

F-1-5

Installation Procedure

■Installing the Open I/F PCB

1) Remove the Left Rear Cover.

• 2 Rubber Caps

• 2 Screws

• 5 Claws

Claws

Rubber Caps

2) When the Reader is installed, remove the Reader Communication Cable.

F-1-6

F-1-7

3) Remove the Left Rear Sub Cover.

• 1 Screw

• 1 Hook

Hook

Left Rear

Sub Cover

4) When the FAX is installed, remove the FAX cable.

F-1-8

F-1-9

Installation Procedure

5) Hold the handle to remove Main Controller PCB 2.

• 2 Screws

Grip

6) Remove the Face Cover. (Removed Face Cover is not used.)

• 2 Screws (Removed screws are not used.)

NOTE:

Ask the user to store the Face Cover and Screws, in case it is needed in the future.

F-1-10

F-1-11

7) Remove the 2 screws (the removed screws are used in step 9)).

8) Remove the Bypass PCB (the removed Bypass PCB is not used).

• 2 Screws (the removed screws are not used)

NOTE:

Ask the user to store the Bypass PCB and Screws, in case it is needed in the future.

F-1-12

F-1-13

Installation Procedure

9) Install the Open I/F PCB.

• 1 Connector

• 2 Screws (the screws removed in step 7))

• 4 Screws (TP; M3x6)

10) Install Main Controller PCB 2.

CAUTION :

• Lift the grip and insert the Main Controller PCB 2. When it touches the end, tilt the

grip and install it with 2 screws.

• Make sure to tilt the grip slowly on both sides simultaneously.

• Check that the Main Controller PCB 2 is installed properly.

Grip

F-1-14

F-1-15

11) Install the FAX Cable (if the FAX is installed).

12) Install the Left Rear Sub Cover. (1 Screw)

13) Install the Reader Communication Cable (if the Reader is installed).

14) Connect the Interface Cable to the installed Open I/F PCB.

15) Cut off [A] part of the Left Rear Cover with nippers.

CAUTION:

Be sure to remove adequately so that there is no burr.

[A]

F-1-16

F-1-17

Installation Procedure > Installing the PS Unit

16) Install the Left Reader Cover. (2 Screws, 2 Rubber Caps)

Installing the PS Unit

1) Remove the 9 Face-Cover Seals on the Rear (The removed Face Seals will not be used.)

2) Install the 2 Support Plates.

• 4 Stepped Screws (M4)

• 4 Screws with Toothed Washers (Binding; M4x8)

Screws with

Toothed Washer

Screws with

Toothed Washer

Stepped Screw

F-1-18

F-1-19

3) Remove the 4 Screws.

4) Install the Mounting Plate with the removed screws.

CAUTION:

Be sure to install it in the correction direction.

Slot Hole

5) Install the PS Unit in the direction of the arrow.

• 4 Screws with Toothed Washers (Binding: M4x8)

F-1-20

F-1-21

Installation Procedure > Installing the PS Unit

6) Install the Interface Cable to the PS Unit.

7) Open the Right Rear Cover, connect one end of the Cross Ethernet Cable to the host

machine and then connect another end to the PS Unit.

• 1 Wire Saddle

Cross Ethernet

Cable

Interface

Cable

8) Close Right Rear Cover 1.

F-1-22

9) Install the 3 Wire Saddles.

10) Connect the Power Cord and the Shield Ethernet Cable to the PS Unit.

11) Secure the cables in place using the 3 Wire Saddle as shown in the gure below.

CAUTION:

• Use the correct power code to mach the location/area of installation. Make sure not

to leave unused power code at the site.

• Be sure to use the network cable with Category 5e or higher. In addition, a sealed

type (STP cable) is recommended. When using the non-sealed type (UTP cable), it

may inuence the surrounding electronic equipments via network cable.

Shield Ethernet

Cable Power Cord

F-1-23

F-1-24

Installation Procedure > Settings after Installation

12) Turn ON the main power switch of the host machine.

13) "Turn ON the main power of the host machine again." is displayed on the touch panel,

turn OFF the main power switch of the host machine.

14) Turn ON the main power switch of the host machine again.

Settings after Installation

1) At the Main menu, press [Printer].

2) Press [Printer Status/Settings].

F-1-25

F-1-26

3) At the Languages Setup screen, select the name of the language you want to use, and

then select OK.

Wait a few minutes.

When setting it up, the password input screen is displayed.

Entering "Fiery.1" in the password eld displays the setting screen.

NOTE:

Use single-byte upper case to enter F of "Fiery.1". Use single-byte lower case to enter

other characters.

In response, the machine will automatically show the Settings menu. Be sure to at least select

the following and make the appropriate settings in the indicated order: [Server Setup], [Network

Setup], and [Printer Setup]. For more information, see Conguration and Setup on the User

Documentation.

For instance, once you have made the various settings under [Server Setup], you will be

shown a screen asking you if you want to store the settings. Select [yes] so that the system

will be stored in memory. Unless you have made appropriate settings in the correct order and

saved them, you will not be able to go on to the next item.

F-1-27

Installation Procedure > Checking the Operation After Making the Settings

Making Server Settings:

Make the appropriate settings including the name of the server.

Making Network Settings:

Make the appropriate settings including port, protocol, and service.

F-1-28

F-1-29

Making Printer Settings:

Make the appropriate settings including print queue.

4) Select [close] on the Settings menu. In response, the system will restart automatically.

Checking the Operation After Making the Settings

Print out a test page and a settings page as follows to make sure that all settings have

correctly been made on the equipment and its host machine and that all connections are

normal:

1) At the Main menu, press [Printer].

F-1-30

F-1-31

Inhaltsverzeichnis

Andere Canon Controller Handbücher

Canon

Canon CR-G100 Bedienungsanleitung

Canon

Canon RC-IP100 Bedienungsanleitung

Canon

Canon imagePASS-P2 Bedienungsanleitung

Canon

Canon Digital Video Software v.32 Betriebsanleitung

Canon

Canon imageRUNNER ADVANCE C9075S PRO Bedienungsanleitung

Canon

Canon imagePRESS C800 Series Betriebsanleitung

Canon

Canon ColorPASS-GX400 Bedienungs- und Wartungshandbuch

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch

Canon imagePASS-B2 Bedienungs- und Wartungshandbuch

Beliebte Controller Handbücher anderer Marken