Canon Color iR Security Kit-A1P Bedienungsanleitung

– 2 –

iR Security Kit – A1P/A1U

Installation Manual

When installing the iR Security Kit - A1P/A1U, follow the instructions given in this manual.

1 Package Check

Open the package of iR Security Kit - A1P/A1U and check that the following items are enclosed:

Fig. 1-1

[1] Protect key device - Parallel (for A1P) ....... 1 pc.

[2] Protect key device - USB (for A1U) ........... 1 pc.

[3] iR Series Security System Setup Tool

CD-ROM..................................................... 1 pc.

[4] User’s Guide ............................................... 1 pc.

[5] Serial number label ..................................... 1 pc.

About storing the protect key devices and CD-ROM after use

Instruct the user to store the protect key devices and iR Series Security System Setup Tool CD-

ROM securely because they are necessary for enabling the Security Option again when the option

is disabled by an operational error in Service mode or other. A protect key device is available only

for a copier where the device was used once. Once a protect key device has been damaged by static

electricity or lost, the Security Option can no longer be set. To prevent this problem, instruct the

user to keep each protect key device in a conductive bag.

About handling the protect key devices

To protect the protect key devices from static electricity, note the following:

• When install the devices, wear a ground wrist strap. If no grounding facility is available, connect

the ground terminal of the wrist strap to the frame of the copier.

• Keep each protect key device in a conductive bag and take it out immediately before use.

• Do not touch the connector terminals of a protect key device.

– 3 –

2 Preparation

2.1 Necessary Materials

a. Parallel connection

• Windows 95/98/NT/2000/XP personal computer

(PC)

(A1U: Not supporting Windows 95/NT)

• IEEE 1284 parallel cable of 1.8 m or shorter

b. Network connection

(iR C3200/C3200S/C3200N, S3200, CLC3200,

imageRUNNER C3200: Network connection only)

• Windows 95/98/NT/2000/XP personal computer

(PC)

(A1U: Not supporting Windows 95/NT)

• 10/100Base-T cross Ethernet cable

2.2 Connecting the Copier to PC

1) Turn off the copier power and PC power.

2) Disconnect the Ethernet cable, parallel cable, and

modular cable connected to the copier.

3) Take the enclosed protect key device (parallel or

USB) out of the conductive bag and connect it to

the parallel or USB port of PC.

4) Connect the copier and PC with the prepared paral-

lel cable or cross Ethernet cable.

5) Turn the PC power on.

6) Turn the copier power on.

• For iR C3200/C3200S/C3200N,

S3200, CLC3200, imageRUNNER

C3200

While holding down the 1 and 7 keys

on the numeric keypad together, turn

the copier power on. (Keep the nu-

meric keys down for several seconds.)

Power-on with the 1 and 7 keys down

automatically sets the network connec-

tion of the copier.

(IP address: 172.16.1.100, subnet

mask: 255.255.255.0)

7) For use through a network connection, set an ap-

propriate network connection to enable communi-

cation between the copier and PC. If the network

connection is changed, turn the PC power and copier

power off and on.

• For iR C3200/C3200S/C3200N,

S3200, CLC3200, imageRUNNER

C3200

Set the IP address and subnet mask of

PC.

(IP address: 172.16.1.10, subnet mask:

255.255.255.0)

2.3 Installing the Protect Key Device Driver

1) Insert the enclosed iR Series Security System Setup

CD-ROM into the PC CD-ROM drive and double-

click the hdd32.exe file on the CD-ROM.

(IRSEC : \English\Vxxxx(version)\hdd32.exe)

2) Select the language and click OK.

Fig. 2-1

3) Click Next.

Fig. 2-2

– 4 –

4) Click Finish to complete the installation.

Fig. 2-3

2.4 Installing the iR Series Security System

Setup Tool

1) Insert the enclosed iR Series Security System Setup

Tool CD-ROM into the PC CD-ROM drive.

2) Double-click the Setup.exe file on the CD-ROM.

(IRSEC : \English\Vxxxx(version)\Setup.exe)

3) Click OK.

Fig. 2-4

4) Click the PC icon.

Fig. 2-5

5) Click Continue.

Fig. 2-6

6) Click Finish to complete the installation.

Fig. 2-7

– 5 –

3Security Option Addition Proce-

dure

3.1 Adding the Security Option

1) Enter Service mode and press COPIER - Option -

FUNCTIN - DOWNLOAD - OK to make the copier

ready for download.

Note that the Security Option cannot

be added in Download mode of Safe

mode (copier power-on with the 2 and

8 keys down).

2) Activate the iR Series Security System Startup Tool

from PC.

3) Check that the type of the connected protect key

device is bi-Centronics for A1P or USB for A1U.

Then click OK.

Fig. 3-1

4) For parallel connection, select bi-Centronics and

click OK. For network connection, select Network,

enter the IP address of the copier, and click OK.

Fig. 3-2

5) Click OK.

Fig. 3-3

6) Click OK.

Fig. 3-4

– 6 –

7) Click END.

Fig. 3-5

8) Click OK to finish adding the Security Option.

Fig. 3-6

9) Turn the copier power off and on.

3.2 Setting Service Mode and User Mode

The Security Option is of the two types below. This

option is enabled only after setting both in Service

Mode and User Mode.

• Hard Disk Data Complete Erase

• Job Log Display

The setting procedure is as follows:

1) Check the user request and set each item in Service

Mode accordingly.

After the following setting, choices for the Security

Option are displayed in User Mode.

• For iR C3200/C3200S/C3200N,

S3200, CLC3200, imageRUNNER

C3200

The items are displayed in Level-2

Service Mode.

For Level-2 Service Mode, enter the

initial screen of ordinary Service Mode

(User Mode key + 2, or 8 + User Mode

key) first. Then press the User Mode

key and 2 sequentially.

• Hard Disk Data Complete Erase

Set whether or not to delete data completely from the

hard disk by overwriting 0 or random data to the file

division at the logical file deletion timing (manage-

ment data deletion timing).

COPIER > Option > USER > HDCR-DSP

0: Do not display in User Mode/Do not erase data (De-

fault)

1: Display in User Mode/Write 0 data once

2: Display in User Mode/Write random data once

3: Display in User Mode/Write random data three times

Change the set value from 0 to 1, 2, or 3.

Memo

The greater the set value, the higher

the data security on the hard disk.

– 7 –

• Job Log Display

Set whether or not to display the history of copying,

fax communication, and printing.

COPIER > Option > USER > LGSW-DSP

0: Do not display in User Mode (Default)

1: Display in User Mode

Change the set value from 0 to 1.

2) Once you have entered System Settings in User

Mode, the Hard Disk Data Complete Erase and Job

Log Display buttons. Set the buttons to ON or OFF

according to the user request.

3.3 After Work

1) Check the serial number of the copier and turn the

power off.

2) Remove the protect key device from PC.

3) Turn the PC power off.

4) Disconnect the cross Ethernet cable between the

copier and PC.

5)Connect the Ethernet cable, parallel cable, and

modular cable disconnected before work.

6) If the network connection of the copier has been

changed, reset the connection to the original set-

tings and turn the power off and on.

7) Enter the serial number of the copier into the en-

closed serial number label and stick the label to the

protect key device (parallel or USB).

Fig. 3-7

8) Put the protect key device in a conductive bag and

pass it to the user with the iR Series Security Sys-

tem Setup Tool CD-ROM.

Instruct the user to store them securely.

Andere Handbücher für Color iR Security Kit-A1P

Dieses Handbuch passt für folgende Modelle

Andere Canon Druckerzubehör Handbücher

Canon

Canon iP4000 - PIXMA Photo Printer Bedienungsanleitung

Canon

Canon Color iR Security Kit-A1P Bedienungsanleitung

Canon

Canon Paper Deck-V1 Bedienungsanleitung

Canon

Canon Cassette Feeding Unit-AM1 Bedienungsanleitung

Canon

Canon Cassette Feeding Module-K1 Bedienungsanleitung

Canon

Canon BW PCL PRINTER KIT-J1 Bedienungs- und Wartungshandbuch

Canon

Canon BW PCL PRINTER KIT-J1 Bedienungs- und Wartungshandbuch

Canon

Canon AG1 Bedienungsanleitung

Canon

Canon IP 1500 Bedienungsanleitung

Canon

Canon Paper Deck Unit-B1 Bedienungs- und Wartungshandbuch

Canon

Canon Cassette Module-AE1 Bedienungsanleitung

Canon

Canon Finisher-R1 Service-Handbuch

Canon

Canon BW Voice Guidance Board-A1 Bedienungsanleitung

Canon

Canon Shift Tray-D1 Bedienungsanleitung

Canon

Canon INNER 2-WAY TRAY-E1 Bedienungs- und Wartungshandbuch

Canon

Canon iP4680 Bedienungsanleitung

Canon

Canon Duplex Color B1 Bedienungsanleitung

Canon

Canon PIXMA Pro9500 Mark II Handbuch

Canon

Canon Inner Finisher Additional Tray-A1 Referenzhandbuch

Canon

Canon DADF-M1 Bedienungsanleitung

Canon

Canon UFRII LT PRINTER KIT-J2 Bedienungs- und Wartungshandbuch

Canon

Canon Buffer Pass Unit-N1 Bedienungsanleitung

Canon

Canon Duplex Unit-A1 Service-Handbuch

Canon

Canon Two-Knife Booklet Trimmer-A1 Bedienungsanleitung

Beliebte Druckerzubehör Handbücher anderer Marken

Star Micronics

Star Micronics TSP800 Series Bedienungsanleitung

REA

REA JET HR pro 2K Bedienungsanleitung

HP Laserjet,Color Laserjet 4si Bedienungsanleitung

oliser

oliser MS 45 Bedienungsanleitung

Roland

Roland DU2-64 Anleitungen und Rezepte

Xerox

Xerox EFI EXP6000 Bedienungsanleitung

Sharp

Sharp FO-1MK Bedienungsanleitung

Labelmate

Labelmate PM-300 Bedienungsanleitung

Epson

Epson T6248 Betriebsanleitung

Epson

Epson OT-BZ20 Bedienungsanleitung

Ricoh

Ricoh LCIT RT5100 Kurzanleitung

GBC

GBC 16 Series Bedienungsanleitung

Develop

Develop SD-509 Bedienungsanleitung

Kyocera

Kyocera KM-6230 Handbuch

Triumph Adler

Triumph Adler DF-710 Handbuch

Citizen

Citizen CBM-202PC Series Bedienungsanleitung

Codonics

Codonics Virtua 1VCX-LR833 Referenzhandbuch

TonerRefillKits

TonerRefillKits ReChargX RX126 Bedienungsanleitung