Canopy Breeze CB101 Bedienungsanleitung

Canopy Breeze® Canopy Fan Quick Start Guide

Model CB101

Congratulations on choosing the Canopy Breeze® canopy fan, the next level of tailgating comfort! To ensure maximum enjoyment and years of trouble-

free service from this product, please read these instructions thoroughly and store them in a safe place. Please visit www.mekooutdoors.com for further

information and instructional videos.

One-Year Limited Warranty

Meko Outdoors, Inc warranties this product to be free from defects in material or workmanship for a period of one (1) year following the date of purchase,

provided the product is used in a non-commercial manner. This limited warranty does not cover failures as a result of abuse, droppage, or using this

product in a manner contrary to its intent. Damage caused by collapsed/toppled canopies as a result of wind or other acts of nature are excluded from

this warranty. For warranty inquiries or claims, please do not return the unit to your retailer. To file a warranty claim, please visit

www.mekooutdoors.com/warranty and complete the online form, or email us at [email protected].

What’s Included

🅐 Master power switch

🅑 Charging port

🅒 5 fan blades

🅓 Motor Assembly

🅔 Fan remote control

🅕 Case

🅖 Battery Housing

🅗 Battery charger

🅘 Downrod Extension accessory

Compatible Frames

Canopy Breeze fits on perpendicular roof and “Push-up” style frames

NON-Compatible Frames

Canopy Breeze will not fit on these type frames

Standard or vented 10’ and 12’ canopies with

perpendicular roof joists, available in most

sporting, hardware and discount stores.

Push-up frames, (also known as “One Push,” or

“Quick Lift”) where a single user can raise the

canopy roof by pushing up a knob in the center

of the frame.

Offset roof joist members are

not

compatible.

Canopies with a center pole, or cross-truss frame

whereby the roof fabric is raised via a center

pole held by truss supports at the top of the legs

are

not compatible.

Before First Use

1. Ensure fan motor (the lower part of the motor assembly that the fan blades snap into) is free from obstruction by gently

rotating it clockwise while holding the fan. You will feel slight resistance approximately every ¾”, and the motor will make a

quiet clicking sound when spinning continuously. Should you rotate the motor

counter-clockwise

and release, a spring clutch

inside the fan will turn the motor clockwise back to its original position. Never spin the fan motor counter-clockwise more than

¼ turn. If the motor does not spin clockwise with minimal effort, do not attempt to use the fan. Contact us at

[email protected] for guidance.

2. Charge the battery approximately 6 hours (or until the LED on the charger changes from RED to GREEN) before using.

Installation

!"#$%&'()*+),---

.*+'&/-0(1121-$3-+')-$+)1+414-5'(-&1(%*+1+)-'6)4''(-$+3)*77*)$'+8--&71*31-3)'(1-.*+'&/-0(1121-$+-.*31-*5)1(-1*.9-6318--&1(%*+1+)-

.'++1.)$'+-'5-)91-.9*(:1(-)'-*+-'6)71)-;$77-<'$4-;*((*+)/8-

!"#;*(+$+:,--

4=->=?-@>A?BCC-=D-=EFDB?F-?GF-HB>-@H-DB@>I-J@>KL-=D-@>MCFNF>?-M=>K@?@=>A-BDF-FOEFM?FK8-

!"#;*(+$+:,--

0F-APDF-?=-AFMPDF-?GF-MB>=EL-J@?G-A?BQFAI-JF@RG?A-=D-D=EF-JGF>-=EFDB?@>R-?GF-HB>8-

STUVWX-<1+)14-.*+'&$13

-J@CC-EPCC-N=DF-B@D-?GB>-F>MC=AFK-MB>=E@FAI-MDFB?@>R-B-N=DF-M=NH=D?BYCF-F>Z@D=>NF>?8-

STUVWX-

$H-APA?B@>FK-J@>KA-BDF-FOEFM?FK-?=-YF-[\-NEG-=D-G@RGFDI-?GF-YDFF]F-HD=N-?GF-HB>-J@CC-YF-CBDRFCL-@>FHHFM?@ZF8

For

PUSH-UP

style canopies

⑤ Once all four hooks are resting on the

canopy frame, the fan will sit level, and the fan

blades can be inserted.

⑥ Insert each of the five fan blades into the slots

on the fan motor assembly and push firmly.

⑦ The inner curve, or concave side of fan

blade must face downward (toward the

ground) when installed.

⑧ You will hear a “click” once the fan blade snaps

into place.

For

STANDARD

Canopies

For

PUSH-UP

style canopies

① Unfold canopy; only raise it halfway

up.

② Raise the four hooks on top of the fan.

③ Center the hooks between the four roof joists of

the canopy frame apex with the hooks over the top of

the frame. Rotate the fan ¼ turn counterclockwise,

then lower each hook onto a roof joist.

④ Depending on the size of the push-up knob on

the canopy, it may be necessary to angle the fan

slightly so the hooks on the fan can clear the

knob.

⑨ Once all the fan blades are in place, turn the

Master Power Switch to the “ON” position

BEFORE

raising the canopy. It will be hard to

reach otherwise.

⑩ Stake the canopy legs securely, place the fabric

top on the canopy, and raise it to full height.

⑪ Remove the clear plastic tab from the back of the

remote and discard before use. You can now operate

the fan using the remote control. The fan blades will

spin in a

clockwise

direction.

Uninstalling Canopy Breeze®

1. Turn the fan off using the remote.

2. Lower the canopy back to the half-height position.

3. Flip the Master Power Switch to the “OFF” position.

4. Remove the fan blades. While holding the motor assembly, grasp the front of the blade firmly. Slightly wiggle the blade from side to side while pulling until the blade slides out. If the blades

still won’t release, remove the fan from the canopy frame and place it upside down on a firm surface, such as a table, to remove the blades. Note that the blades will become easier to remove

over time.

5. Lift the fan unit up over the canopy frame and rotate clockwise ¼ turn to remove.

6. Lower the hooks and snap them back into their cradles on the top of the battery housing.

7. Place all components back into the case and locks clasps securely.

⚠"#Please be sure Master Power Switch is in the “OFF” position when storing the fan. If not, the remote could inadvertently start the motor

and cause damage to the fan and or case.

Center Hoop for Hook Mounting

Your fan comes with a hoop on the top for installation on a hook. This will allow for use in other applications in addition to

canopies. Please use extreme care when hook mounting.

1. We recommend a hook that is #12 size or bigger, and must support at least 10 lbs.

2. If hanging from a ceiling or gazebo, please be sure the hook is attached directly into the wooden frame or stud

under drywall. Do not use hooks that are mounted only in drywall, even if using a drywall anchor.

NOTE: HOOK MUST BE COMPLETELY THREADED INTO WOOD FRAME AS TORQUE FROM THE FAN COULD

UNSCREW IT, CAUSING IT TO FALL.

4. Allow a minimum of 7.5’ of clearance between the fan blades and ground, or 6” higher than the tallest occupant.

5. Once the fan is placed on the hook, secure it with a zip or wire tie for extra safety.

Down Rod Extension

Due to the height and roof pitch of certain canopy frames, air flow created by Canopy Breeze may need to be closer to the

occupants. The included down rod extension allows the fan to hang an additional 10” lower than using the four hooks on top of

the fan. This puts the breeze from the fan blades closer to the occupants, and also allows the fan to circulate air that is slightly

cooler than the air next to the fabric canopy roof.

1. To install, simply open the extension into a “V” shape, and hang it over two of the four canopy frame roof joists that

are aligned with each other.

DO NOT

hang it on roof joists that are perpendicular to each other.

2. Hang the fan on the bottom hook of the extension via the center hoop mounted on top of the fan.

3. Allow a minimum of 7.5’ of clearance between the fan blades and ground, or 6” higher than the tallest occupant.

Should the fan blades be lower than this, remove the extension and hang the fan using the four hooks as outlined in

Steps 1-5.

4. Be sure all fan blades are completely inserted so the fan will be balanced, and be sure to test the fan for wobble by

turning on the motor before occupants are underneath.

5. If the fan wobbles, this usually indicates one or more fan blades are not inserted completely.

Charging and Battery Care

⚠#$WARNING: Only recharge this product with the supplied charger.

1. Plug the charger into a standard 120 Volt 60 Hz electrical outlet. While charging, the LED in the charger will illuminate red. When charging is complete, it will illuminate green. If the charger is

blinking red, this indicates a faulty battery. Please contact us for further guidance.

2. Typical recharge time after use is 5 hours from 10% battery charge.

NOTE:

The fan will run indefinitely while the charger is connected to power.

ALWAYS

disconnect power when the fan is not in use and the battery is fully charged. Permanent connection to

AC power will shorten the life of the fan’s circuitry and void the warranty.

Battery disposal.

This product uses a Lithium-ion rechargeable and recyclable battery. When the battery will no longer hold a charge, it should be removed from the fan and recycled. It

should not be incinerated or composted. Contact your local recycling center for information on where to dispose of it properly. In the event the battery in your fan needs replacing, please

Battery Tips.

The powerful lithium-ion battery included with your fan is by far its most expensive component. Maximize the life of your battery with these handy tips:

a. Try to avoid “deep discharge” by not letting the battery drain completely.

b. It’s best to store the fan in an environment of 80°F or cooler. Try not to leave the fan in a hot car for an extended period of time.

c. Once the charger illuminates green, unplug it. The battery will discharge approximately 5% over the next several days, and you can “top it off” the day before its next use.

d. When storing the fan for long periods of time, only charge the battery to 30-50%. Try to avoid storing the battery at 100% charge for an extended period as this will shorten

battery life.

e. When using the fan regularly, it is OK to run it for a short period of time, then recharge the battery back to full. Lithium-ion batteries do not have “battery memory,” so partial

discharge/recharge will not harm them.

Troubleshooting

If after installation the fan will not operate, try one of the following:

1. With the power off, can you rotate the fan motor (the lower portion of the fan body that holds the fan blades) clockwise with a soft clicking sound? When spinning the motor, you will feel a

stop approximately every ¾” inch, and this is considered normal. If the motor will not spin, do not use the fan. Contact us at [email protected] for further guidance.

2. Was the fan fully charged before first use, with the LED on the charger illuminating green?

NOTE:

If the LED on the charger is blinking red when plugged into the fan, this indicates a faulty

battery. Please contact us at [email protected] for further guidance.

3. Was the Master Power switch on the fan body moved to the ON position before raising the canopy to full height?

4. Was the clear plastic battery safety tab removed from the back of the remote?

5. Does the LED on the front of the remote light up red when any buttons on the remote are pushed?

NOTE:

The LED on the remote should illuminate brightly. Should the LED look dim or

pinkish in color, this could indicate a low battery or defective remote.

If all the above steps have been taken, and the fan still will not operate, please contact us at [email protected] for further assistance.

For questions and further information, please visit our website, www.mekooutdoors.com or email us at service@mekooutdoors.com.