4INSTALLATION GUIDE HARLO Please keep this instruction manual for future reference
GUARANTEE
-Your Caple tap is guaranteed for 5 years.
-Should you have any defects as detailed above during the appropriate guarantee period we guarantee to repair or replace
the defective products or parts, or, at our option refund the purchase price assuming we were advised immediately of any
claim in writing.
-It is important that you keep a proof of purchase (such as your receipt) to facilitate your guarantee.
INSTALLATION INSTRUCTIONS
-Turn the spout and body so the tap is facing forwards, the
screw on the spout indicates the rear of the body. The hot
water connection should be on the left of the tap.
-Ensure the hot and cold pipes are thoroughly flushed to remove
any debris.
-A 35mm hole is required in either the sink or worktop.
-The fixing bolt must be screwed into the tap base, ensuring the
threads of the bolt are not damaged in the process.
-Pass the nylon washer over the fixing bolt flush to the bottom
of the tap base, then pass the bolt through the sink or worktop
(ensuring the nylon washer remains directly under the tap
base).
-Pass the rubber washer and then the metal washer (on the
underside of the sink/worktop) over the fixing bolt and fix using
the fixing nut.
-Screw the flexi-tail pipes into the base of the tap, ensuring the
pipes threads are not damaged in the process. If the flexi-tails
are already inserted into the tap base, please ensure these are
screwed in tightly to prevent any leaks.
-Finally connect the flexi-tail pipes to the hot and cold supplies
ensuring they are connected to the correct supplies.
CARE OF YOUR TAPS
-Only clean your taps with soap or mild liquid detergent and
clean water then dry using a soft cloth
-Do not use chemical cleaners, or bleach based
solutions to clean your tap, contact could affect the finish of
your tap.
-Do not use abrasive cleaners, liquids, powders or pads. These
will damage the finish of your tap and void the guarantee.
-Provided all of the above points are adhered to the surface
finish of your Caple Tap is guaranteed for 5 years.
PRE INSTALLATION CHECKS
-The temperature of the hot water supply must not
exceed 70°C.
-Water pressure requirements: minimum required pressure
varies dependent on model, maximum pressure 5 bar.
-Always seek advice from a qualified installer to ensure your
installation and water supply to your taps comply with the
water regulation (WRAS) requirements and good plumbing
practice.
-It is good practice to ensure that both hot and cold water
supplies to your tap are of an equal pressure to provide a
consistent flow. If supplies are not of equal pressure then a
non return valve should be fitted on the hot inlet.
-Supplies of water should be from a common source (mains or
tank fed).
-We recommend that a service valve is installed in the
supply lines to the tap to enable water isolation if required.
POST INSTALLATION POINTS
-We suggest when connecting screw connections that PTFE tape
is used before the joints are fully tightened.
-Before use correctly check the installation for leaks, and
turn the hot and cold water on to thoroughly flush any
small particles that may have been dislodged during the tap
installation.
THESE INSTRUCTIONS ARE INTENDED AS A GUIDE,
IF IN ANY DOUBT ENSURE YOU SEEK ADVICE
FROM A CERTIFIED PLUMBER.
TERMS AND CONDITIONS
-Guarantee conditions are only valid if the Care guidelines listed above are followed.
-Our obligation under the guarantee is to the original purchaser, and may not be transferred.
-The guarantee is valid for UK domestic installations only and relates to defects in manufacture, materials and
workmanship only.
-Issues that arise due to normal wear and tear (for example valves, discs or washers), poor installation,
improper use or accidental damage are not covered by the Caple guarantee. Spare parts can be purchased
from our Customer care helpline 0117 938 1900.
-No liability is accepted for consequential damage to other household fixtures, fittings or furnishings relating
to any claim - even if attached to the product.
-If it is more economically viable a replacement tap will be supplied, this tap might vary from the original
design should range changes of occurred since the initial supply.
-We reserve the right to inspect any tap before committing to support under the guarantee conditions.
