Carefree BT12 Bedienungsanleitung

070029-001r2 Printed in USA July, 2018

INSTALLATION

BT12 Wireless Awning Control System

ONTROL

YSTEM FOR

12V

OTORIZED

WNINGS

SING

LUETOOTH

WIRELESS TECHNOLOGY

Read this manual before installing or using this product. Failure to follow the instructions

and safety precautions in this manual can result in personal injury and/or cause the

product to not operate properly.

The BT12 Wireless Awning Control System may be installed as part of the original motorized awning

installation or as an upgrade to an existing motorized awning installation.

The system offers unique features not available with a standard awning installation.

1) Carefree Connects Mobile App – The app provides full and enhanced control of the awning using a

smart phone or tablet. The free app can be downloaded on any devices that support: 1) Current iOS

or Android operating systems, and 2) Bluetooth low energy technology.

2) Full Retract – When the awning is retracted, it retracts completely. It is not necessary to hold the

button when closing the awning.

3) Full Extend – When the awning is extended, it extends completely. It is not necessary to hold the

button when opening the awning.

4) Auto-Retract – The awning can be set to automatically close when windy conditions occur with the

optional BT Motion Sensor.

5) Remote Control – The operator can conveniently operate the awning from any location with the

optional BT Remote.

BT12 WIRELESS AWNING CONTROL SYSTEM INSTALLATION MANUAL CAREFREE OF COLORADO

2 070029-001r2

NOTICES AND DISCLAIMERS

TRADEMARKS

The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc.

Use of such marks by Carefree of Colorado is under license.

Other trademarks and trade names are those of their respective owners.

STATEMENTS OF COMPLIANCE

●BT12 Control Module ●BT Motion Sensor ●BT Remote

FCC and IC identification numbers are located on the exterior surfaces of the individual components.

FCC

OMPLIANCE

These devices comply with Part 15 of the FCC rules. Operation is subject to the following two

conditions: (1) These devices may not cause harmful interference and, (2) These devices must accept

any

interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Any changes or modifications not expressly approved by the party responsible for compliance could void

the user’s authority to operate the equipment.

OMPLIANCE

These devices comply with Industry Canada license-exempt RSS standard(s). Operation is subject to the

following two

conditions: (1) These devices may not cause harmful interference and, (2) These devices must

accept any

interference received, including interference that may cause undesired operation.

Ces appareils sont conformes aux normes RSS exonérées de licence d'Industrie Canada. L'opération est

soumise aux deux conditions suivantes: (1) Ces appareils ne doivent pas causer d'interférences nuisibles et, (2)

Ces appareils doivent accepter toute interférence reçue, y compris les interférences pouvant entraîner un

fonctionnement indésirable.

FCC/IC

ADIATION

XPOSURE

TATEMENT

●BT12 Control Module ●BT Motion Sensor

This equipment complies with FCC and IC radiation exposure limits for an uncontrolled environment. The

minimum distance between the radiator and people is designed to be 20cm when installed and operated.

Cet équipement est conforme aux limites d'exposition aux radiations FCC et IC pour un environnement non

contrôlé. La distance minimale entre le radiateur et les personnes est de 20cm lorsqu'installé et utilisé.

●BT12 Remote

This equipment complies with FCC and IC radiation exposure limits for an uncontrolled environment. The

minimum distance between the radiator and people is designed to be 5mm when operated.

Cet équipement est conforme aux limites d'exposition aux radiations FCC et IC pour un environnement non

contrôlé. La distance minimale entre le radiateur et les personnes est de 5mm (à l'exclusion des extrémités:

mains, poignets, pieds et chevilles) lors de l'utilisation.

CAREFREE OF COLORADO INSTALLATION MANUAL BT12 WIRELESS AWNING CONTROL SYSTEM

070029-001r2 3

DISCLAIMERS

The BT12 Wireless Awning Control System and the Carefree Connects Mobile App are products of

Carefree of Colorado, located in Broomfield, Colorado, USA. The

information contained in or disclosed in

this document is considered proprietary to Carefree of Colorado.

Every effort has been made to ensure

that the information presented in the document is accurate and

complete. However, Carefree of

Colorado assumes no liability for errors or for any damages that result from

the use of this document.

The information contained in this manual pertains to the current components and software listed on the title

page. Carefree of

Colorado reserves the right to cancel, change, alter or add any parts and

procedures, described in this

manual, without prior notice.

Carefree of Colorado agrees to allow the reproduction of this document for use with Carefree of Colorado

products only. Any other reproduction or translation of this document in whole or part is strictly prohibited

without prior written approval from Carefree of Colorado.

SERVICE AND SUPPORT

www.carefreeofcolorado.com/carefreeconnects

[email protected]

Carefree of Colorado

2145 W. 6th Ave.

Broomfield, CO

80020

TABLE OF CONTENTS

Installation .....................................................................................................................................5

BT12 Control Module Installation............................................................................................................6

Awning Switch Installation ......................................................................................................................7

Awning Lights Switch Installation............................................................................................................7

Wiring Diagram.......................................................................................................................................8

Installing the BT Motion Sensor............................................................................................................10

Altitude / Longitude / Latitude.......................................................................................................10

Small Box Awnings.......................................................................................................................10

Pairing the Motion Sensor ............................................................................................................10

Setting the System into Pairing Mode...................................................................................................11

Battery Replacement...................................................................................................................12

BT Motion Sensor.................................................................................................................................12

BT Remote............................................................................................................................................12

BT12

IRELESS

WNING

ONTROL

YSTEM

NSTALLATION

ANUAL

AREFREE OF

OLORADO

4 070029-001r2

AFETY

NFORMATION

This is the safety alert symbol. It is used to alert individuals to potential

personal injury hazards. Obey all safety messages that follow this symbol to

avoid possible personal injury or death.

WARNING

Indicates a hazardous situation, which if not avoided, could result in death or

serious bodily injury.

CAUTION

Indicates a hazardous situation, which if not avoided, may result in minor or

moderate bodily injury.

NOTICE

Indicates a situation that may result in equipment-related damage.

General Safety:

WARNING

SHOCK HAZARD. Always disconnect battery or power source before

working on or around the electrical system.

WARNING

Always wear appropriate safety equipment (i.e. goggles).

WARNING

FALL HAZARD. ALWAYS use a ladder that meets or exceeds the

standards and requirements of the American National Standards Institute and the

Occupational Safety and Health Administration. ALWAYS follow the manufacturer’s

instructions for ladder safety. Failure to follow this warning could result in death or

serious bodily injury.

CAUTION

Always use appropriate lifting devices and/or helpers when lifting or

holding heavy objects.

NOTICE

When using fasteners, do not over tighten. Soft materials such as fiberglass and

aluminum can be "stripped out" and lose the ability to grip and hold.

The state of California requires the following warning:

CALIFORNIA PROPOSITION 65

WARNING

This product contains chemicals known to the state of California to cause

cancer or birth defects or other reproductive harm. California’s Proposition 65 requires this

warning to be given to customers in the state of California.

AREFREE OF

OLORADO

NSTALLATION

ANUAL

BT12

IRELESS

WNING

ONTROL

YSTEM

070029-001r2 5

INSTALLATION

WARNING

SHOCK HAZARD. Always disconnect battery or power source before

working on or around the electrical system.

Important Note: To comply with 2015 NFPA 1192 RV Standard, Section 6.4.9, switches must be

mounted as follows:

a) Installed in a dedicated switch cabinet with a latching door; or,

b) Installed with the optional covered bezel available from Carefree; or,

c) Installed in a cabinet with a latching door where the switch is protected and CANNOT be activated by any

items or cargo that may move or shift during transit; or,

d) Installed with an interrupt circuit that disables awning extension when the vehicle is in motion.

1. The BT12 module provides an ignition lockout option. When the “IGN LOCK” is connected to the

vehicle PCM or other switched source the following parameters are set:

i) If Open = Awning Active

ii) If tied to GND = RTL (Retract Then Lock) – Awning retracts, extend command disabled

iii) If tied to +12Vdc = Standard – Extend command disabled

To Start:

1. Determine the location for the awning switches, awning lights switch and BT12 control module.

NOTE: The BT12 control module leads are 6" in length. If the distance between the module and the

switches is greater than 6", the installer must furnish splice wires for the extra distance. Use

appropriate size wire gauges. Use appropriate sized butt splices to secure connections.

2. Route the motor cable and LED harness to the location of the module.

BT12 WIRELESS AWNING CONTROL SYSTEM INSTALLATION MANUAL CAREFREE OF COLORADO

6 070029-001r2

BT12 CONTROL MODULE INSTALLATION

(Refer to the wiring diagram on page 8.)

NOTICE Do not mount the unit near heat producing elements such as LP appliances or engine

exhaust components.

NOTICE For best reception, do not mount the unit near or on a metal surface.

1. Clean the mounting surface. The surface must be flat

and clean for the mounting tape to properly adhere.

2. Remove the release paper from the tape on the back

of the module and firmly press the module onto the

mounting surface.

NOTE: The module may be oriented for best fit with

access to the wire leads.

3. Attach the motor wires (refer to diagram for

corresponding wire colors) to the module leads for the

motor using 14-16awg butt splices.

4. Run a minimum 14 awg wire to chassis ground.

Suitable ground would be the vehicle chassis or

conductive structure connected to the chassis. Splice the wire to the module GND lead with a 14-

16awg butt splice.

5. Run a minimum 14 awg wire from the power distribution panel (auxiliary battery circuit) or equivalent. The

circuit should be protected by a 15-amp fuse. Splice the wire to the module +12V lead with a 14-16awg

butt splice.

NOTE: If the wire run is 30 feet or longer for +12Vdc and/or GND, use 12awg wire to prevent voltage

drop. Use the appropriate butt splices for the wire size.

6. Splice the Black wire from the LED Harness to the module LED GND lead (Black) with a 18-22awg butt

splice.

7. Route the module LED + lead (RED) to the awning lights switch location. Use 20awg wire and 18-

22awg butt splice to extend the lead as necessary.

8. Route the module IGN LOCK lead (Green) to the vehicle PCM or other switch source (used for ignition

lockout).

9. Route the remaining wires (Violet, Gray, Yellow and Brown) to the location for the awning control

switches. Use 20awg wires and 18-22awg butt splices to extend the leads as necessary.

Remove

Release Paper

Mounting

Tape

BT003

CAREFREE OF COLORADO INSTALLATION MANUAL BT12 WIRELESS AWNING CONTROL SYSTEM

070029-001r2 7

AWNING SWITCH INSTALLATION

(Refer to the wiring diagram on page 8.)

1. At the switch location cut a 2 5/16"

[5.9cm) x 1 1/2" [3.8cm] hole.

2. From the module, terminate the

three (3) 20awg wires (Brown,

Yellow and Gray) with .187, 18-20

awg female terminals. Attach to

the EXTEND/RETRACT switch as

shown in the wiring diagram.

3. From the module, terminate the

Violet wire with a .187, 18-20 awg

female terminal. Attach to the

ON/OFF switch.

4. Run a minimum 14 awg wire to

chassis ground. Suitable ground

would be the vehicle chassis or

conductive structure connected to

the chassis. Terminate the wire with

.187, 14-16 awg female terminal and

connect to the second terminal of the

ON/OFF switch.

NOTE: If the wire run is 30 feet or longer, use 12awg wire to prevent voltage drop. Use the

appropriate wire terminals for the wire size.

5. Push the wires and switches into the hole then attach the switch frame using 4 #6 x 1/2" screws.

6. Snap the switch bezel over the switch frame.

AWNING LIGHTS SWITCH INSTALLATION

NOTE: Carefree offers two switch options, unlighted and lighted. Installers may choose to furnish the

control switch or may wire directly to a multiplexing control center.

1. Determine the location of the switch.

2. At the switch location, cut a 1 1/8" x 1 1/2" hole.

3. Wire the switch as shown. Wire terminals at the switch are .187, 18-24 awg female disconnects.

NOTE: The lighted switch has a third terminal. This is wired to GND.

OFF

1.13"

1.5"

1.88"

2.9"

#6 x 1/2

Screw (x2)

BT004d

Single Pole, Single Throw Switch

Lighted Single Throw Switch

GND

White/Violet

(20awg)

To +12 V DC

White/Violet

(20awg)

To +12 V DC

Multiplexing Control Connection

White/Violet

(20awg)

To Multiplexing

Controller

1" [2.5cm]

BT001

2.32" [5.9cm]

1.5"

[3.8cm]

#6 x 1/2" Screw (x4)

RETRACT

EXTEND

OFF

Awning Control

RETRACT

EXTEND

Awning Control

OFF

Optional

Covered Bezel

BT12 WIRELESS AWNING CONTROL SYSTEM INSTALLATION MANUAL CAREFREE OF COLORADO

8 070029-001r2

WIRING DIAGRAM

Extend/

Retract

On/Off

Rear View of

Switch Assy

.187, 18-20awg Female

Spade Terminals (x5)

Red

Black

Top

Bottom

To +12VDC

GND

Red

Black

LED Strip

Violet

Green

Black

(16awg)

Red

(16awg)

Control Module

To vehicle PCM

or other switched source

White

(16awg)

Blue

(16awg)

White/Black

(20awg)

White/Red

(20awg)

(18awg)

Red

(18awg)

Single Pole, Single Throw Switch

Lighted Single Throw Switch

GND

Gray

Brown

(18awg)

BT002e

DETAIL B

Awning Lights Switch Options

DETAIL A

Motor Connect

Dry Connectors

Direct Motor Control

Freedom WM, Freestyle WM, Marquee

Brown

Blue

White

(16awg)

Blue

(16awg)

MOTOR

Freedom RM, Freestyle RM

Blue

Brown

White

(16awg)

Blue

(16awg)

MOTOR

Eclipse, Travel’r, Latitude, Longitude, Altitude

Red

Black

Top

Bottom

White

(16awg)

Blue

(16awg)

MOTOR

To +12VDC

Yellow

(18awg)

White/Violet

(20awg)

To +12VDC

White/Violet

(20awg)

To +12VDC

White/Violet

(20awg)

To +12VDC

Multiplexing Control Connection

White/Violet

(20awg)

To Multiplexing

Controller

Violet

Green

(18awg)

Gray

Brown

(18awg)

Yellow

(18awg)

Violet

Green

(18awg)

Gray

Brown

(18awg)

Yellow

(18awg)

Com

To vehicle PCM

or other switched source

3To vehicle PCM

or other switched source

+12VDC

Awning Disable

Switch

+12VDC

Awning Disable

Switch

5 5

DETAIL C

Multiplex Control System

CAREFREE OF COLORADO INSTALLATION MANUAL BT12 WIRELESS AWNING CONTROL SYSTEM

070029-001r2 9

For GND, run a minimum 14 awg wire to chassis ground. Suitable ground would be the vehicle chassis

or conductive structure connected to the chassis.

For +12Vdc, Run a minimum 14 awg wire from the power distribution panel (auxiliary battery circuit) or

equivalent. The circuit should be protected by a 15-amp fuse.

NOTE: If the wire run is 30 feet or longer, use 12awg wire to prevent voltage drop. Use the

appropriate wire terminals for the wire size.

The BT12 module leads are 6" in length. If the distance between the module and the switch is

greater than 6", the installer must furnish splice wires for the extra distance. Use appropriate size

wire gauges. Use appropriate sized butt splices to secure connections.

The BT12 module provides an ignition lockout option. When the “IGN LOCK” is connected to the

vehicle PCM or other switched source the following parameters are set:

a) If Open = Awning Active

b) If tied to GND = RTL (Retract Then Lock) – Awning retracts, extend command disabled

c) If tied to +12Vdc = Standard – Extend command disabled

The LED connection is optional to provide LED controls through the app for white LEDS only.

White LEDS can also be installed per the standard LED installation without BT12 Controls. RGB

lights must be installed per the standard RGB installation.

The awning disable switch is a single pole, single pole switch used with OEM Multiplexing Control

Systems. Switch is furnished by installer.

BT12 WIRELESS AWNING CONTROL SYSTEM INSTALLATION MANUAL CAREFREE OF COLORADO

10 070029-001r2

INSTALLING THE BT MOTION SENSOR

The system operates by gauging the motion of the awning's front edge (roller tube or lead rail). When the

motion exceeds the preset threshold the system retracts the awning. The factory default is “3” on a scale

from 1 to 5. When using the mobile app, the sensitivity can be adjusted for personal preference.

The sensor is located in the motor head for vertical arms or in the lead rail for box awnings.

Altitude / Longitude / Latitude

1. Remove the front cover on the motor side.

The cover snaps onto the rear cover.

1.1. Altitude / Longitude: Press in on both

sides of the rear cover in the area

shown. Rotate the cover up and off.

1.2. Latitude: Press the bottom of the rear

cover until the front cover releases then

lift the front cover off.

2. Clean the inside surface of the rear cover.

3. Remove the release paper from the

mounting tape on the back of the bracket.

4. Firmly press the bracket onto the inner

surface of the rear cover.

Small Box Awnings

This option is available for Freestyle WM and

Freestyle RM. It is not available for the

Freedom WM, Freedom RM or Marquee.

1. Open the awning to expose the inside of the

lead rail on the motor side.

2. Clean the inside surface of the lead rail.

3. With the module bracket oriented

horizontally, as shown, remove the release

paper from the mounting tape.

4. Firmly press the bracket onto the inner

surface of the lead rail between the end

plate and arm connector on the motor side

of the awning.

Pairing the Motion Sensor

NOTE: Only 1 active motion sensor can be

paired to the BT12 Control Module

1. After completing the installation restore

power to the awning and extend the awning

using the switches.

2. Place the awning in pairing mode (refer to

page 11).

3. Remove the battery pull tab from the motion sensor.

4. Hold the motion sensor next to the control module for 2-3 seconds. The module should be paired.

5. Holding the sensor vertically with the Carefree logo upright, repeatedly move the sensor vertically up

and down to simulate a brisk wind. The awning should retract.

6. Snap the module in the sensor bracket.

7. For Altitude / Longitude / Latitude: Snap the front cover onto the rear cover. Hang the cover on the top

and swing down until it clicks.

Front

Cover

BT013

Press Up On Rear Cover

to Release Front Cover

Remove

Release Paper

Attach Bracket

to Inside of

Rear Cover

Motion

Sensor

Latitude

Thumb Tab

Down

Attach Bracket

to Inside of

Rear Cover

Thumb Tab

Small Box Awning

(Freestyle WM Shown)

Remove

Release Paper

Motion

Sensor

Battery

Pull Tab

Battery

Pull Tab

Remove

Release Paper

Thumb Tab

Down

Front

Cover

Thumb Tab

Motion

Sensor

Battery

Pull Tab

Press on both sides

of the rear cover to

release front cover

Thumb Tab

Altitude / Longitude

(Altitude Shown)

Andere Handbücher für BT12

Inhaltsverzeichnis

Andere Carefree Steuerungssystem Handbücher

Carefree

Carefree BT12 Bedienungsanleitung

Beliebte Steuerungssystem Handbücher anderer Marken

Pentair Pool Products

Pentair Pool Products Compool Bedienungsanleitung

ComfortNET

ComfortNET CTK04 Bedienungsanleitung

Fireye

Fireye InSight II 95DSS3 Bedienungsanleitung

CAME

CAME G3000 Bedienungsanleitung

Idemia

Idemia MorphoAccess VP MD Bedienungsanleitung

Axis

Axis P1445-LE-3 Bedienungsanleitung

HEIDENHAIN

HEIDENHAIN TNC 150 B Bedienungsanleitung

CNC-Step

CNC-Step High-Z T-Series Bedienungsanleitung

Doosan

Doosan DVF Series Bedienungsanleitung

Honeywell

Honeywell KAP 140 Bedienungsanleitung

Honeywell

Honeywell vk41 series Bedienungsanleitung

AirBench

AirBench FPW Installationsanleitung

Cypress

Cypress HHR-3160 Bedienungsanleitung

CAME

CAME GLT40AOS Bedienungsanleitung

Zonex

Zonex GEN II -VVT Benutzerhandbuch

Altronics

Altronics K 9650 Bedienungsanleitung

micro-trak

micro-trak RoadMaster Bedienungsanleitung

micro-trak

micro-trak Calc-An-Acre II Bedienungsanleitung