Carlon HS3620 Handbuch

INSTRUCTION GUIDE

Motion-Activated Security Light HS3620

Congratulations on a wise purchase!

ENCLOSED YOU WILL FIND:

• Security Light Control

• Wireless Motion Sensor

• Wireless Remote Control

• Screws

• One 12-volt alkaline battery (installed)

TOOLS NEEDED:

• Phillips screwdriver

BATTERIES NEEDED (not included):

• Four AA alkaline batteries

LIGHT CONTROL WIRING

1. Turn off electricity at the circuit breaker or fuse.

2. With gasket in place, connect the white wire from the light control base to the

white wire in the electrical box, using the provided wire nut.

3. Connect the black wire from the light control base to the black wire in the

electrical box, using the provided wire nut.

4. If a ground wire is present, attach the green ground wire in the electrical box

under the head of the green ground screw on the metal light control base.

5. Mount the light control base onto the electrical box. When completed, be sure

that the perimeter of the gasket is even to assure a proper seal.

6. Install the PAR lamps (Type PAR38 bulbs, incandescent, 150 watts maximum per

lampholder). Aim the PAR lamps as desired. Tighten locknuts and adjustment

screws.

7. Turn on the electricity to the outdoor light location. (The ﬂoodlights will not come

on until the wireless motion sensor is installed.)

8. Use the wireless remote control to test operation.

Note: Power must be applied continually to the light control. If a wall switch

previously controlled the light control location, this switch must be in the "on"

position.

MOTION SENSOR INSTALLATION

Note: The motion sensor can be mounted or set anywhere, indoors or outdoors,

at a height of 0 to 10 feet from the ground. For

best range and detection, mount at least 6 feet

from the ground.

For mounting:

A. Place adjustable mounting bracket (provided)

where desired (such as a post, tree, house)

and install top screw into key slot. Then secure

the bottom screw.

B. Slide the motion sensor down onto the bracket.

Adjust the motion sensor to the desired angle.

Note: To tighten the ball joint, use a Phillips screwdriver to turn the adjustment

screw on the bracket.

Important: The bottom cover must face downward after installation so that

moisture cannot enter.

SET-UP

1. Remove the wireless motion sensor

bottom cover by pressing inward on the

latch.

2. Pull tab to bring out the battery holder

and install four AA alkaline batteries. Be

sure that the battery (+) and (-) terminals

match the (+) and (-) contacts shown in

the battery compartment.

3. The day/night switch should be in the

day/night mode.

4. The timer (or left) switch should be in the

leftmost position (6 s) for test. With the

switch in this position, the ﬂoodlights will

turn off approximately 6 seconds after

turning on. This will allow quick testing of

the motion sensor with the light control.

5. Replace bottom cover.

TEST

1. Walk through the coverage area. Note when the ﬂoodlights turn on. If the

coverage area needs to be changed, adjust the motion sensor for improved

coverage. Retighten the ball joint screw.

2. After completing the test, determine the amount of on-time you want for the

ﬂoodlights to stay on after motion is detected. The timer switch allows the

choices of 10 minutes (rightmost switch position) or 3 minutes (center switch

position).

3. Also decide if you want the light control to turn on during the day and night

when motion is detected or just at night. Set the Detect switch to the left for

night only operation and to the right for day/night operation.

4. Close the bottom cover.

DETECTION ZONE

White wires

Black control wire

& black junction

box wire

Lampholder

Junction box

Motion is detected in a 60’ x 140˚ range

which will be over 4396 sq. feet. The

mounting bracket can be adjusted to

customize the detection zone.

Note: As with most motion detection

devices, pets or other animals may

activate the unit. Also, walking in

a straight line towards the motion

sensor may reduce operating range.

Walking across the detection field

provides the maximum operational

range.

REMOTE CONTROL

Press the "on" or "off" button to over-

ride the system and turn light on

or off.

TO REPLACE REMOTE CONTROL

BATTERY

Remove the top screw from the back

of the remote control. Lift off the

back cover, remove old battery and

insert new battery according to the

(+,-) placement guides. Replace the

back cover along with the screw. The

remote control will now be ready to

operate.

Left

COVERAGE AREA

140º

Top View

MOUNTING BRACKET ADJUST-

MENT

60'

Side to Side

Up and Down

Right

CHANGING SYSTEM CODE (optional)

The user can change the system code signal if interference occurs with opera-

tion. If you use other wireless products in your home, there is a slight possibility

of interference. Use the following instructions to change the current system code

setting to a new setting.

Important: If you change the system code on the motion sensor, you must also

change the code on the light control and remote control. If the system code does

not match on all items, the system will not function properly!

1. Turn off the power to the ﬂoodlights.

2. Unscrew the plug on the front of the light control case.

3. Pull out one of the two jumper shunts (black rectangular piece) and reposi-

tion in a different position and note the letter designation for the new jumper

conﬁguration.

4. Replace the plug and turn on the power to the light control.

5. Remove the wireless motion sensor bottom cover.

6. Set the two jumper shunts in the same jumper conﬁguration as in the light

control.

7. Re-install the motion sensor bottom cover.

8. Remove remote control's back cover.

9. Set the two jumper shunts in the same jumper conﬁguration as in the light

control and motion sensor.

10. Replace back cover.

TROUBLESHOOTING TIPS:

PROBLEM: Floodlights do not come on when there is motion in front of motion

sensor or when turned on by the remote control.

SUGGESTION: Conﬁrm power is on at circuit breaker. Conﬁrm wall switch has

been turned on. Conﬁrm if unit works with remote control. Set the motion sens-

ing transmitter On-time switch to the "6 s" setting (leftmost position). Verify that

the yellow LED, behind the front lens, turns on when there is motion activity in

front of the motion sensor. If the LED does not turn on, check battery polarity or

replace the batteries in the motion sensor transmitter. Reset the On-time switch

to its original position.

Check that the ﬂoodlight assembly and receiver are mounted within 100’ of the

motion sensor or remote control. Check that the system code is the same in the

motion sensor and in the light control. Check that metal objects do not block the

motion sensor signal or move the light control.

PROBLEM: Floodlights go on and off randomly.

SUGGESTION: Change the system code in the motion sensor, light control, and

remote control.

SPECIFICATIONS

Motion Sensor

Motion detection range: Up to 60’ x 140˚

Batteries: 4 AA alkaline

Light Control

Maximum Load: 300 watts incandescent total, 150 watts per lampholder

Voltage: 120VAC, 60Hz

Motion sensor also works with HS3605, HW2150D, HW2165D, HW2170D, HW2190,

and RC7000D.

LIMITED WARRANTY

The product you have purchased is guaranteed against defects in workman-

ship and materials for the period stated on the package. Warranties implied

by law are subject to the same time period limitation. Some states do not allow

limitations on how long an implied warranty lasts, so this time limitation may

not apply to you.

If the product fails due to a manufacturing defect during normal use, return the

product and dated sales receipt to the store where purchased for replacement

OR send the product and the dated sales receipt to:

Lamson & Sessions

25701 Science Park Drive

Cleveland, OH 44122 USA

Attn: LHP Customer Service

Not Covered - Batteries, light bulbs, and other expendable items are not covered

by this warranty. Repair service, adjustment and calibration due to misuse,

abuse or negligence are not covered by this warranty. Unauthorized service or

modiﬁcation of the product or of any furnished components will void this warranty

in its entirety. This warranty does not include reimbursement for inconvenience,

installation, set-up time, loss of use, postage, unauthorized service, or other

products used in conjunction with, but are not supplied by, Lamson & Sessions.

All requests for replacement must include a dated sales receipt (copies accepted).

LAMSON & SESSIONS IS NOT LIABLE FOR LOST PROFITS, INDIRECT, SPECIAL,

EXEMPLARY, INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING WITHOUT

LIMITATION ANY SUCH DAMAGES DUE TO IMPROPER WIRING OR MISUSE OF THE

PRODUCT. As some states do not allow the exclusion or limitation of incidental

or consequential damages, the above limitation and exclusion may not apply

to you.

This device complies with Part 15 of the FCC rules. Operation is subject to the

following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that

may cause undesired operation.

This device complies with RSS-210 of Industry Canada.

ALSO AVAILABLE FROM CARLON:

• Extend-A-Chime® – lets you hear your existing wired doorbell in remote areas

of your home or yard

• Plug-in and Battery Doorbells and Chimes

• On/Off Remote Switches

• Touch and Automatic Lighting Controls

This warranty gives you speciﬁc legal rights, and you may also have other

rights which vary from state to state. If you have questions or need further

assistance, please call Lamson & Sessions at: 1-800-346-2646 Mon. - Fri.,

9 a.m.-4 p.m. EST

0404 IS158

Made in China

25701 Science Park Drive

Cleveland, Ohio 44122

www.lamson-sessions.com

Andere Carlon Scheinwerfer Handbücher

Carlon

Carlon HS570 Handbuch

Beliebte Scheinwerfer Handbücher anderer Marken

VIZULO

VIZULO Micro Martin Benutzerhandbuch

EuroLite

EuroLite LED IP FL-100 SMD Bedienungsanleitung

Cooper Wheelock

Cooper Wheelock XB12 Bedienungsanleitung

Allen + Roth

Allen + Roth 17624-000 Bedienungsanleitung

ADJ

ADJ 4 STAGE PAK Bedienungsanleitung

Cooper Lighting

Cooper Lighting EGL91SW233 Bedienungsanleitung

Max

Max 37496 Bedienungsanleitung

BEGA

BEGA 85 143 Bedienungsanleitung

Beamz

Beamz 151.226 Bedienungsanleitung

EuroLite

EuroLite LED IP FL-8 Bedienungsanleitung

Ledj

Ledj PERFORMER 36 RGB Bedienungsanleitung

Perel

Perel ELS3 Bedienungsanleitung

Perel

Perel ELS3WD Bedienungsanleitung

LumX

LumX LM 36130 Bedienungsanleitung

Xtricity

Xtricity 4-80053 Bedienungsanleitung

Stahl

Stahl 6521/4 Series Bedienungsanleitung

Ecosense

Ecosense EcoSpec Bedienungsanleitung

Ayrton

Ayrton minipanel FX Bedienungsanleitung