Carpenter MFG C1565 Bedienungsanleitung

Model No. C1565

http://www.carpenterpowertools.com

15 GAUGE

FINISH NAILER

TABLE OF CONTENTS

TECHNICAL SPECIFICATIONS

SAFETY GUIDELINES

KEY PARTS DIAGRAM

TECHNICAL INFORMATION

TYPES OF NAILS

OPERATING INSTRUCTIONS

TROUBLESHOOTING

EXPLODED VIEW

PARTS LIST

TABLE OF CONTENTS

TECHNICAL SPECIFICATIONS

SAFETY GUIDELINES

Model No. C1565 contact us 1-888-666-1887

Operating pressure

Dimensions

(Length*Height*Width)

Net Weight

Nail capacity

Air consumptio

PERSONAL SAFETY

These precautions are intended for the personal safety of the user and others working

with the user. Please take time to read and understand them.

Make sure you read and understand this manual before using this tool. Make sure other

users read and understand this manual before they use the tool.

SAFETY GUIDELINES

This manual contains information that relates to PROTECTING PERSONAL SAFETY and

PREVENTING EQUIPMENT PROBLEMS. It is very important to read this manual carefully

and understand it thoroughly before using the product. The symbols listed below are used to

indicate this information.

70–120 psi (4.9–8.3 bar; 5– 8.5 kgf/cm²)

13-1/2"(L)x12"(H)x3-1/4"(W)

(344mmx304mmx82mm )

4.41 lbs (2.0 kg)

100 PCS

.045 ft3/cycle at 100 psi

(1.3 ltr/cycle at 6.9 bar)

(1.3 ltr/cycle at 7 kgf/cm²)

DANGER!

Potential hazard that could result in serious

personal injury including possible death.

WARNING!

Potential hazard that could result in serious

personal injury to the tool user or others in the

work area.

CAUTION!

Potential hazard that could result in damage

to the tool or property.

WARNING!

Potential hazard that could result in serious personal injury to

the tool user or others in the work area.

• Always wear eye and hearing protection when using the air compressor. Failure

to do so may result in sight or hearing loss.

• Do not overload the tool. Allow the tool to operate at its optimum speed for

maximum efciency.

• Do not point the tool towards yourself or other people, even when the tool has

stopped. Keep hands, feet, and all other parts of the body clear from work area.

• Do not attempt to clear nailer jams while the air hose is connected.

• Do not keep the trigger or the Push Lever pressed while loading nails.

SAFETY GUIDELINES

NOTE: Some commercial air line drying liquids are harmful to “O” rings and seals—

Do not use these low temperature air dryers without checking compatibility.

SAFETY GUIDELINES

CAUTION!

• DANGER! Potential hazard that could result in serious personal

injury including possible death.

• Do not use oxygen or any other combustible or bottled gas to

power air-powered tools. Failure to observe this warning can

cause explosion and serious personal injury or death.

• Do not use this tool in the presence of ﬂammable liquids, dust or gases. Sparks that

are created during use may ignite these materials.

• Use only compressed air to power air-powered tools. Use an approved air hose with

a minimum length of 25' (7.6 m).

• Do not allow inexperienced or untrained individuals to operate any air-powered tool.

• Keep hands and other parts of the body away from the Outlet (Firing Head) during use.

• Nails or objects in the workpiece can cause serious injury if they are deﬂected by the

workpiece.

• Keep children away from the work area. Do not allow children to handle power tools.

• Never point nailer toward yourself or anyone else.

• Always assume the nailer contains fasteners. Never point the nailer toward yourself or

anyone else, whether it contains fasteners or not. If fasteners are mistakenly driven, it

can lead to severe injuries. Never engage in horseplay with the nailer. Respect the nailer

as a dangerous working implement.

• Disconnect the tool from the air supply and turn off the

compressor before performing any maintenance, when the

tool is not in use, when it is being handed to another person,

when it is left unattended, or when loading and changing

nails. Failure to comply may result in injury or damage to

equipment.

• Do not exceed the maximum or minimum pressures.

Operating the tool at the wrong pressure (too low or

too high) may cause excessive noise or rapid wear.

• Use only Non-Detergent Air Tool Lubricating Oil for this tool.

• Near and below freezing, moisture in the air line may freeze and prevent tool

operation. Do not store in a cold weather environment to prevent frost or ice

formation. Frost and ice on the tools operating valves and mechanisms could

cause tool failure.

Potential hazard that could result in damage to the tool or property.

Model No. C1565 contact us 1-888-666-1887

15 Gauge ﬁnish Nailer

Regulator

Quick connector

Filter

Quick coupler

Cut -off valve

Air hose

Air compressor

Lubricator

COMPATIBLE COMPRESSORS

GUIDELINES FOR PROPER USE AND OPERATION

Be sure to use a proper air compressor with CARPENTER Air Tools. The compressor should be able

to supply a minimal air delivery of 4.7 CFM @ 90 PSI to ensure the compressor can run continuously

with the CARPENTER 15 Gauge ﬁnish Nailer.

GENERAL USE

No. Description No. Description

The C1565 is ideal ﬁnish nailer for interior trim,exterior trim,baseboards,crown molding,window and

door casings,chair rails and so on, it accepts 15-gauge nails from 1-1/4" up to 2-1/2" in length.The

tool is lightweight and durable, stands up to the elements and provides consistently accurate results

over the life of the tool. An ideal tool for a variety of construction projects, including installation of

asphalt rooﬁng shingles and insulation boards. It also features a high-capacity side-load magazine,

tool-less depth adjustment, durable construction, and more.

•It is recommended that a ﬁlter-regulator-lubricator be used and be located as close to the tool

•If a ﬁlter-regulator-lubricator is not installed, place up to 6 drops of compressor oil into the air

inlet plug before each use.

•If a ﬁlter-regulator-lubricator is installed, keep the air ﬁlter clean. A dirty ﬁlter will reduce the

air pressure to the tool, which will cause a reduction in power, efﬁciency, and general

•Verify that all of the connections in the air supply system are sealed in order to prevent air leakage.

Read and follow all the safety instructions at the beginning of this manual and inspect the

air-powered nailer prior to each use in order to ensure that the proper power source is being used

and verify that the tool is in proper working order

Model No. C1565 contact us 1-888-666-1887

KEY PARTS DIAGRAM

TECHNICAL INFORMATION

Top Cover

Air Outlet

Exhaut Cover

Piston O-ring

Piston

Driver Blade

Lock Lever

Nail Feeder(A)

Guide Plate(A)

Push Lever

Outlet(Firing Head)

Blade Guide

Nail Feeder(B)

Valve part

Switching Device

Trigger

Body

Cap

Air Plug

Nail Rail

Nail Stopper

Magazine

Ribbon Spring

Adjuster

125 7

1110

ACCEPTABLE NAILS LOADING NAILS

STANDARD ACCESSORIES

Only nails shown in the Table below can be driven with this Nailer.

Safety glasses

Allen wrench for M6 screw

Allen wrench for M5 screw

Nose cap

Model No. C1565 contact us 1-888-666-1887

TYPES OF NAILS

OPERATING INSTRUCTIONS

15 Gauge ﬁnish nails Min. Max.

3.Pull the nail feeder(B) back to engage the

nail feeder(A) to the nail strip (Fig.A).

1.Insert nail strip into rear of magazine (Fig.A).

2.Slide the nail strip forward in the magazine.

The nail strip should pass the nail stopper (Fig.B).

Magazine

Nail Stopper

Fig. A

Fig. C

Fig. B

Nail Feeder (A)

Nail Feeder (B)

1 2 3 4

1312

Model No. C1565 contact us 1-888-666-1887

OPERATING INSTRUCTIONS

REMOVING NAILS

3.Remove the remainning nails from the

magazine (Fig.F).

1.Disconnect Air hose (Fig.D).

2.Depress the nail feeder and slowly slide

the nail feeder forward (Fig.E).

Fig. D

Fig. F

Fig. E

DANGER!

●Do not drive nails on top of other nails or with nailer at too steep an angle.

Nails can ricochet and seriously injure someone.

●In order to avoid double ring or unwanted ejection of a nail due to

bouncing of the nailer, do not push nailer on workpiece to avoid recoil.

Recoil is necessary for proper operation of the nailer.

●Do not drive nails from both sides of a wall at the same time. Nails can

be driven into and through the wall and hit a person on the opposite side.

●Never drive nails into thin boards or near corners and edges of workpiece.

Nails can be driven through or away from workpiece resulting in serious or

life threatening injury.

●Never use a nailer which is defective or operating abnormally.

●Never use a nailer as hammer.

METHOD OF OPERATION

The Carpenter Air-powered Brad Nailer is equipped with a push lever at the nailing point and will not

operate unless the push lever is depressed (pushed upwards)(Fig.G).

Fig. G

①Single Actuation Mechanism

1.Set the switching device to the position as (Pic I);

2.Make sure the push lever position to the workpiece,Pull the

gunbody and keep the push lever connect to the workpiece and

then press the trigger,It start to work;

3.After the rst nails re,loosen the trigger and raise up the

gunbody,Position the push lever to the workpiece and rework as

above steps.

②Contact Actuation Mechanism

1.Set the switching device to the position as (Pic II);

2.Press the trigger rst and then postition the push lever to the

workpiece,Press the push lever and begin to re;

3.After the rst nails out, hold the trigger tight,and raise up the push

lever,Make sure the push lever postion to the workpiece,and then

press it and rework as above steps.

Pic I

Pic II

1514

Model No. C1565 contact us 1-888-666-1887

OPERATING INSTRUCTIONS

TROUBLESHOOTING

Fig. H

Fig. J Fig. K

ADJUSTING THE NAILING DEPTH

To assure that each nail penetrates to the same depth, be sure that:

① The air pressure to the Nailer remains constant (regulator is installed and working properly).

②The nailer is always held rmly against the workpiece. If nails are driven too deep or too shallow into the

workpiece, adjust the nailing depth using the following instructions.

1.Disconnect air hose from nailer (Fig. H).

2a. If the nails are driven too deep, pull the adjuster

downward and turn counter-clockwise (Fig. J).

2b. If nails are driven too shallow, pull the adjuster

downward and turn clockwise (Fig. K).

3. Connect the air hose and perform a nailing test. ALWAYS WEAR EYE PROTECTION.

4. If additional adjustments are necessary, DISCONNECT AIR HOSE FROM NAILER and repeat step 2.

Disconnect air hose

1.Open the guide (Fig.L).

2.Remove the jammed nails with a slotted-head

screwdriver (Fig.M).

Fig. M

Fig. L

1716

Model No. C1565 contact us 1-888-666-1887

OPERATING INSTRUCTIONS

TROUBLESHOOTING

Note: Solvent sprayed on the nose to clean and free up the push lever

may have the opposite effect.The solvent may soften the tar on the

shingles and cause tar buildup to be accelerated.Dry operation is better.

• Lubrication: If the air-powered nish nailer

and the compressor are not equipped with

an in-line lubrication system, place up to

6 drops of pneumatic tool oil into the air

inlet before each work day or after every 2

hours of continuous use, depending on the

characteristics of the workpiece and type

of fasteners used.

• Air-operated tools must be inspected periodically and worn or broken parts must be

replaced to ensure that the tools are operating safely and efciently.

• Inspect and replace worn or damaged O-rings, seals, etc. Tighten all screws and caps

frequently in order to help prevent personal injury.

• Keep the magazine of the tool clean and free of any dirt or abrasive particles.

MAINTENANCE

None

X X

See below X

MAINTENANCE

REQUIRED

TOOLS OR

MATERIALS

REQUIRED

DESCRIPTION Each Use or

Every 2 Hrs

MAXIMUM SERVICE INTERVAL

Monthly As

Needed

General inspection-

free movement

In-depth inspection

Replace worn or

broken parts

Lubrication

Adjusting screw assembly

Movable magazine

Worn or broken

parts

Pneumatic tool

oil

TROUBLESHOOTING

Most minor problems can be resolved quickly and easily using the table below.

If problems persist,contact a Carpenter for assistance.

SYMPTOM

PROBLEM

SOLUTIONS

Nailer operates,but no

nail is driven.

1. Check for a jam.

2. Nail feeder damaged?

3. Ribbon spring weakend or damaged?

4. Check for proper nails.

1.Clear a jam per page 18.

2. Replace nail feeder.

3. Replace ribbon spring.

4. Use only recommended nails.

Weak drive.

Slow to cycle.

1. Check air pressure.

2. Check position of nailing depth

adjustment adjuster.

3. ------

4. Driver blade worn

5. Piston O-ring worn or damaged?

1. Increase air pressure.(Do not

exceed 120 psi(8.3bar 8.5kg/cm²)

2. Readjust per page 15.

3. Use Hitachi pneumatic tool lubricant.

4.Contact Hitachi for replacement.

5.Contact Hitachi for replacement.

Drives too deep.

1. Check air pressure.

2. Check position of nailing depth

adjustment guide plate (A)

1. Reduce air pressure.(Adjust 70-120psi)

(4.9-8.3bar 5-8.5kg/cm²)

2. Readjust per page 15.

Skipping nails.

Intermittent feed.

1. Check for proper nails.

2. ------

3. Nail feeder damaged?

4. Ribbon spring weakend or damaged?

1. Use only recommended nails.

2. Lubricate the nail rail per page18.

3. Replace nail feeder.

4. Replace ribbon spring.

Nails jam Driven nail is

bent.

1. Piston O-ring worn or damaged?

2. Check for proper nails.

3. ------

4. Driver blade worn?

1. Contact Hitachi for replacement.

2. Use only recommended nails.

3. Lubricate the nail rail per page18.

4. Contact Hitachi for replacement.

Drives properly during

normal operation,but does

not drive fully at faster

nailing speeds.

1. Check inside diameter of air hose. 1. Use larger air hose.

1918

Model No. C1565 contact us 1-888-666-1887

EXPLODED VIEW

PARTS LIST

Hex bolt M6X12

Plate

Air exhauster

Hex bolt M5X20

Exhaust cover

Gasket

Washer

Head Valve Spring

O-ring 20.4X2.4

Head valve

Cylinder

O-ring 46X2

Collar

O-ring 56X2.4

O-ring 45X3.55

O-ring 34.5X3.55

Main piston

Bumper

Washer

Shift lever

Gunbody

Mixed plate

Hex bolt M6X30

Movable Plate

Roll pin 4x14

Guide Plate

Roll pin 3x20

Spring

Locked nut M5

Safety shelf

Driver head

Steelball Dw=2

Spring

Adjustable Nut

Safety tip

Safety sleeve

O-ring 14X1.8

O-ring 20X1.8

Valve bushing

O-ring 6.1X1.8

O-ring 6.4X2

O-ring 9X1.8

Sleeve

Switch Spring

O-ring 2.4X1.6

Valve plunger

Valve bushing

Roll pin 3x22

Roll pin 3x20

Trigger

Safety shield

Roll pin 3x16

Guide seat

Roll pin 3x35

Steelball Dw=4

Spring

Shift knob

Roll pin 3x10

Coil Spring

Roll pin 2.5x20

Hex bolt M5X16

Washer d=5

Magazine cover

Nail Rail

Pusher seat

Nail Stopper

Pusher

Spring

Nail groove

Sleeve

Handle Sleeve

End Cap

Washer

1/4 NPT18 Air inlet plug

Air plug

Block

Hex wrench M5/4mm

Hex wrench M6/5mm

Oil pot

297072

777879

Inhaltsverzeichnis

Andere Carpenter MFG Nagelpistole Handbücher

Carpenter MFG

Carpenter MFG CP635 Bedienungsanleitung

Beliebte Nagelpistole Handbücher anderer Marken

Performance Tool

Performance Tool M643 Bedienungsanleitung

Hitachi

Hitachi VH650 - Fencing Nailer, Full Head Bedienungsanleitung

Parkside

Parkside PET 25 B1 Bedienungsanleitung

Senco

Senco Fusion Technology F-35XP Bedienungsanleitung

Grizzly

Grizzly G1847 Bedienungsanleitung

Ryobi

Ryobi R18N18G Bedienungsanleitung

Black & Decker

Black & Decker 492848-00 Bedienungsanleitung

HOLZMANN MASCHINEN

HOLZMANN MASCHINEN TN90 Bedienungsanleitung

Metabo HPT

Metabo HPT NR 3690DC Bedienungsanleitung

Surtek

Surtek CN650 Abmessungen und Installationsanleitung

Makita

Makita GF600 Bedienungsanleitung

Parkside

Parkside PET 25 B1 Bedienungsanleitung

Senco

Senco AirFree 25 Bedienungsanleitung

Freeman

Freeman P50LSLW Bedienungsanleitung

Aicon PRO

Aicon PRO DAC4507 Bedienungsanleitung

DAJ

DAJ XR150A Bedienungsanleitung

Makita

Makita AN923 Bedienungsanleitung

Grizzly

Grizzly T20644 Bedienungsanleitung