Carrier KN-COPP-3-RC Bedienungsanleitung

Carbon Monoxide

Alarm

User’s Guide

Please have the following information

ready when calling:

CO Model number (located on back of alarm):

CO Assembly number (located on back of alarm):

Date of Manufacture (located on the back of the alarm):

Date of Purchase:

Where Purchased:

For questions concerning your Carbon Monoxide Alarm,

please call our Consumer Hotline at 1-800-880-6788.

Attention: Please take a few minutes to thoroughly read this manual, which should be saved for future

reference and passed on to any subsequent owner. If you have any questions about the operation or instal-

lation of your alarm, please call our toll free Consumer Hotline at 1-800-880-6788.

OMKNCOPP-01

810-2680 REV. A

09/05

TEST-RESETPEAK LEVEL

Carbon Monoxide

ALARM

PARTSPERMILLION OF CO

(Lb = Low or NoBattery)

IAS 6-96 2ND EDITION CO ALARM

ALSO COMPLIES WITH CSA 6.19-01

See page

23 for “What to do when

the alarm sounds”

CARRIER CO Alarm with

Digital Display and Peak Level Memory

Model: KN-COPP-3-RC

Assembly: COALMCCNRB01-A

IAS 6-96 SECOND EDITION CO ALARM

ALSO COMPLIES WITH CSA 6.19-01

Quick Set Up Guide

Introduction

Features

•Views

•What CO alarms can and cannot do

Installation

Battery Installation

Battery Backup Operation

Operation

•Normal operating characteristics

• Testing the electronics

•How to know if your alarm is malfunctioning

•How to care for your alarm

• Peak level memory

Carbon Monoxide

•Home safety tips

•Warning signs

What to Do When the Alarm Sounds

•How to respond to the alarm

•Who you should call if you suspect you have CO in your home

Technical Information

•Product Specifications

•How the unit determines when to alarm

•Replacement of the alarm

•Display readings

•Li-Ion battery handling precautions

Limited Warranty

Table of Contents

IMPORTANT

THIS CARBON MONOXIDE ALARM IS DESIGNED TO

DETECT CARBON MONOXIDE FROM ANY SOURCE OF

IMPROPER OR MALFUNCTIONING APPLIANCES. IT IS NOT

DESIGNED TO DETECT SMOKE, FIRE, OR ANY OTHER GAS.

WARNING!

THIS CARBON MONOXIDE ALARM IS NOT A SUBSTITUTE FOR

INSTALLING AND MAINTAINING AN APPROPRIATE NUMBER

OF SMOKE ALARMS IN YOUR HOME.

THIS CARBON MONOXIDE WILL NOT SENSE SMOKE, FIRE, OR

ANY POISONOUS GAS OTHER THAN CARBON MONOXIDE.

FOR THIS REASON YOU MUST INSTALL SMOKE ALARMS TO

PROVIDE EARLY WARNING OF FIRE AND TO PROTECT YOU

AND YOUR FAMILY FROM FIRE AND ITS RELATED HAZARDS.

NOT SUITABLE FOR INSTALLATION IN HAZARDOUS LOCA-

TIONS AS DEFINED IN THE NATIONAL ELECTRIC CODE.

DURING POWER OUTAGE, THIS UNIT WILL OPERATE FOR

APERIOD OF ATLEAST 20 HOURS ON A FULLY

CHARGED CARRIER RECHARGABLE BATTERY PACK.

THIS PRODUCT IS INTENDED FOR USE IN ORDINARY

INDOOR RESIDENTIAL AREAS. IT IS NOTDESIGNED TO

MEASURE COMPLIANCE WITH COMMERCIAL AND

INDUSTRIAL STANDARDS.

THE INSTALLATION OF THIS DEVICE SHOULD NOTBE

USED AS A SUBSTITUTE FOR PROPER INSTALLATION,

USE AND MAINTENANCE OF FUEL-BURNING APPLI-

ANCES, INCLUDING APPROPRIATE VENTILATION AND

EXHAUST SYSTEMS.

INDIVIDUALS WITH MEDICAL PROBLEMS MAY CONSIDER

USING WARNING DEVICES WHICH PROVIDE AUDIBLE AND

VISUAL SIGNALS FOR CARBON MONOXIDE CONCENTRA-

TIONS UNDER 30 PPM.

Quick Set Up Guide

Step 1

Determine the best location for your CO alarm(s). Usually

this is in or near bedrooms.

The alarm should be located where it can

wake you if it alarms at night.

Refer to page 8 for installation location

information.

Step 2

Your CO alarm is equipped to be mounted as a corded unit, a direct

plug unit or a table top unit. In the “as shipped” configuration, the unit

can be plugged directly into a wall socket. (If your outlets are mount-

ed horizontally, please refer to page 11, “to rotate adapter”). If the

transformer/adapter is taken out of the unit, the alarm can be mount-

ed on the wall at eye level, while the transformer is plugged into a

wall socket. The unit can also be set on a table if the support at the

bottom of the unit is pulled out (see “rear view” illustration on page

10). Refer to pages 10-12 for further information on installing your

alarm.

Step 3

A Carrier rechargeable battery pack is provided for backup in the

event of a power outage. To install the battery pack, open the back

door and align the connector with the slot in the battery. Insure the

orientation of the two alignment ribs align with the slots in the battery

case.

Press the connector in until it is fully seated. Depending on the

charge state of the battery pack (the battery packs can have different

amounts of energy stored in them due to storage time), you may hear

the alarm sound briefly to indicate the alarm is receiving power.

Place battery pack into battery compartment and replace back door

(refer to page 13).

Note:

Battery backup will be limited until the battery has fully

charged. It may take up to 24 hours for the battery back up to fully

charge.

Step 4

Plug the alarm into a standard, unswitched 120 volt AC electric outlet

in one of the configurations listed in step 2.

We urge you to read this entire manual

in the sequence it is presented.

Listed below are six easy steps for setting up your Carrier CO alarm.

Please read this entire guide for complete information.

Setting up your alarm for first time operation:

Step 5

If the battery pack has a full charge when first powered up, you will

see three eights in the digital display indicating the alarm is warming

up. After approximately 20 seconds, the first reading will be dis-

played. The number on the display should be “0”. If the battery pack

is partially charged,“Lb”(Low battery) will flash every second alternat-

ing with a “0” until the battery is charged. If this occurs, see page 13

for complete information.

Step 6

Make sure the red dot in the digital display is blinking. Test the unit’s

operation by pressing and releasing the Test/ Reset button. Within

15 seconds you will hear 4 quick “chirps” - followed by 5 seconds of

silence - followed by 4 quick “chirps”.

While testing the alarm, have someone else check that the alarm

can be heard easily from the sleeping areas. For complete testing

information, refer to page 16.

Caution:

Continuous exposure to the loud 85 decibel alarm at close

range over an extended period of time may cause hearing loss.

Your Carrier CO alarm is now monitoring for the presence of carbon

monoxide.

Quick Set Up Guide

This Carrier carbon monoxide (CO) alarm is an important part of your

family’s home safety plan. As a new owner of a CO alarm, there are

some basic facts you should know for your protection and convenience.

Many people think that CO alarms operate like smoke alarms. Like

smoke alarms, CO alarms monitor the air in your home and sound a loud

alarm to warn you of trouble.

The way you respond to a CO alarm is quite different than a smoke

alarm. That’s because a house fire and a carbon monoxide problem are

two distinctly different situations. If your smoke alarm were to alarm, you

would quickly be able to judge the level of danger you were in with your

senses. You can see and smell the smoke, feel the heat, see, and pos-

sibly hear the fire burning. You can also readily see if your smoke alarm

is alarming in a non-emergency situation, for example someone smoked

up the kitchen with some burnt toast. Because your sense of sight, smell,

hearing and touch give you information, you can almost instantly judge

what action to take if you hear your smoke alarm.

Carbon monoxide (CO) is invisible, odorless, tasteless, nonirritating, poi-

sonous gas that is completely undetectable to your senses. It is created

when any fuel is burned – gasoline, propane, natural gas, oil, wood, coal,

and even tobacco. When oxygen is limited during combustion, more CO is

produced. Serious problems can develop when combustion by-products

are not properly vented outside the house. That’s why it’s so important to

your safety that you have a carbon monoxide alarm.

Please take the time to completely read this guide to familiarize yourself

with the facts about carbon monoxide, how your new unit works, and

what to do if it alarms. Find a handy place to keep this manual so that it

will be readily available when you have a question.

Thank you for making Carrier a part of your complete home safety pro-

gram. With proper installation and use, your new Carrier CO alarm will

provide you with years of dependable service.

Introduction

Features

TEST-RESET PEAK LEVEL

Carbon Monoxide

ALARM

PARTS PER MILLION OF CO

(Lb = Low or No Battery)

Alarm

Sounder

Digital

Display

Test/Reset

Button

Blinking

Red Dot

Peak Level

Button

Carrier CO Alarm – rear view

Removable

Adapter

Thumb

Release

Thumb Grip for

Back Door

Removal

(Slide Down)

Back Door

Slide Support for Table Top

and Direct Plug Use

Door “Latches”

at all four

corners of

back door

Carrier CO Alarm – front view

Key Holes

Features

Digital Display

The continuous digital display shows you the level of carbon monoxide (if any) the

unit is sensing. The unit updates the digital display every 15 seconds .

Note: If the unit does not sense any CO, the reading is zero (0). In most homes,

the unit reads “0” all the time. A reading of “0” is expected under normal conditions.

The blinking dot after the number shows the unit is operating.

Test/Reset Button

The Test/Reset button has three functions:

1. Press this button to test the unit weekly (see page 16 for further

details).

2. Press this button to silence the alarm. This will reset the unit and it

will then start monitoring for CO. If the CO concentration is above 70

ppm the alarm will again sound within 6 minutes.

3. Press the Test/Reset button to reset peak level memory. (See page

19).

Peak Level Button

By pressing this button, you can see the peak CO level recorded by

the alarm since it was last cleared or unplugged. This Carrier feature

allows you (or a heating contractor or a fireman) to see exactly how

serious the CO problem you have so you can react accordingly.

Sensor

The sensor is a highly sensitive, electrochemical sensor that is CO-

specific to help avoid false alarms.

Sounder Alarm

This is the loud 85 decibel pulsing alarm that will sound to alert you to

apotential problem. An alarm condition is 4 quick “chirps” – followed

by 5 seconds of silence – followed by 4 quick “chirps”. This pattern

repeats until the alarm is silenced or a high level of CO is no longer

present.

Caution: Continuous exposure to this sound level at close range

over an extended period of time may cause hearing loss. We recom-

mend you cover the sounder with your finger or thumb while testing

the alarm.

Keyholes

When the alarm is mounted to the wall, the keyholes slide onto the

screws mounted in the wall.

Features

Rear view with back door removed

Power

Cord

Adapter Cord

Strain Relief

Note:Your Carrier CO alarm is NOT battery operated.

The backup battery is to supply short-term backup power dur-

ing a power outage. In the event of a power outage, the battery

will continue operating the alarm for at least 20 hours.

Cord

Recess

Pull-Out Transformer/Adapter

This unique Carrier feature enables the alarm to be used as a direct plug

unit, a wall mounted unit or a table top unit.

Note:

This CO alarm is not battery operated.

Warning : Do not use any other type of rechargeable battery in your

alarm or attempt to recharge the battery pack yourself. Improper charg-

ing may even cause the battery pack to overheat or leak, thus posing

possible injury to the user.

Carrier

Rechargeable

Backup Battery

(shown installed in

battery compartment)

Install Backup Battery

For correct installation, refer

to Step 3 in the ‘Quick Set

Up Guide’ on page 1 and

refer to ‘Battery Installation

and Operation’ on page 13

What Carbon Monoxide Alarms Can and Cannot Do

CO alarms are designed to sense unacceptable levels of CO from

malfunctioning furnaces, appliances, gas engines or other sources.

This Carbon Monoxide alarm is not a substitute for installing and

maintaining an operational smoke alarm.

CO alarms provide early warning of the presence of carbon monox-

ide, usually before a healthy adult would experience symptoms.

This early warning is possible, however, only if your Carrier CO

alarm is located, installed and maintained as described in this

user’s guide.

This CO alarm is designed to act as a monitor, it is not designed

for use as a short-term testing device to perform a quick check for

the presence of CO.

CO alarms have limitations. Like any other electronic device, CO

alarms are not fool-proof.

CO alarms have a limited operational life. You must test your CO

alarm weekly, because it could fail to operate at any time. If your

CO alarm fails to test properly, or if its self-diagnostic test reveals a

malfunction, immediately have the unit replaced. See back page for

warranty information. This CO alarm also has an "operational end

of life" feature which will indicate when to replace the alarm. See

page 25 for details of this feature.

CO alarms can only sense CO that reaches the unit’ssensor.

Carbon monoxide may be present in other areas without reaching

the alarm. The rate at which CO reaches the unit may be affected

by doors or other obstructions. In addition, fresh air from a vent or

open window or any other source may prevent CO from reaching

the sensor. Please observe cautions on page 8 “Where to install

your alarm.”

CO could be present on one level of the home and not reach a CO

alarm installed on a different level. For example, CO in the base-

ment may not reach an alarm on the second level, near the bed-

rooms. For this reason, we recommend you provide complete cov-

erage by placing a CO alarm on every level of the home.

CO alarms should not be used to detect the presence of natural

gas (methane), propane, butane, or other combustible fuels.

CO alarms are not a substitute for property,disability,life or other

insurance of any kind. Appropriate insurance coverage is your

responsibility.Consult your insurance agent.

Features

CO alarms are not smoke alarms. CO alarms do not sense smoke or

fire. For early warning of fire you must install smoke alarms, even

though carbon monoxide can be generated by a fire.

Inhaltsverzeichnis

Andere Carrier Kohlenmonoxid-Alarm Handbücher

Carrier

Carrier COALMCCNRB02-A10 Bedienungsanleitung

Beliebte Kohlenmonoxid-Alarm Handbücher anderer Marken

Honeywell

Honeywell H450EN Bedienungsanleitung

First Alert

First Alert FCD2B Bedienungsanleitung

Honeywell

Honeywell SF350RVUL Bedienungsanleitung

Poolguard

Poolguard DAPT-2 Bedienungsanleitung

Ei Electronics

Ei Electronics Ei 261D Handbuch

Bacharach

Bacharach Model 105 Handbuch

Firex

Firex COZ-1 Bedienungsanleitung

Costar

Costar 12RV-D Bedienungsanleitung

First Alert

First Alert CO410 Bedienungsanleitung

FireAngel

FireAngel CO-9X Bedienungsanleitung

Costar

Costar 12-24SIR Bedienungsanleitung

Kidde

Kidde KN-COEG-3 (900-01 13) Bedienungsanleitung

System Sensor

System Sensor CO1224T Bedienungsanleitung

Deltronic Security

Deltronic Security CN-1231 Bedienungsanleitung

GE Interlogix

GE Interlogix 240 COE - Carbon Monoxide Alarm Bedienungsanleitung

Sygonix

Sygonix 2377794 Bedienungsanleitung

Kidde

Kidde 8LLCO Bedienungsanleitung

Convoy Tech

Convoy Tech CO311 Bedienungsanleitung