Carrier RG10L/BGEF Bedienungsanleitung

Table of Contents

Remote Controller Specifications

......................................................02

Handling the Remote Controller ....................................................03

Buttons and Functions ...................................................................04

Remote Screen Indicators ..............................................................06

How to Use Basic Functions ..........................................................07

How to Use Advanced Functions ..................................................10

NOT SURE WHAT A FUNCTION DOES?

Refer to the How to Use Basic Functions and How to Use Advanced Functions sections

of this manual for a detailed description of how to use your air conditioner.

SPECIAL NOTE

• Button designs on your unit may differ slightly from the example shown.

If the indoor unit does not have a particular function, pressing that function’s button on

the remote control will have no effect.

When there are wide differentces between “Remote controller Manual” and “USER’S

MANUAL” on function description, the description of “USER’S MANUAL” shall prevail.

•

Remote Controller Specifications

Quick Start Guide

RG10L(G2HS)/BGEF, RG10L(G2HS)/BGEFU1, RG10L1(G2HS)/BGEF,

RG10L1(G2HS)/BGEFU1, RG10L10(G2HS)/BGEF,RG10P(G2HS)/BGEF,

RG10P(G2HS)/BGEFU1, RG10P1(G2HS)/BGEF, RG10L(D2HS)/BGEF,

RG10L(D2HS)/BGEFU1, RG10L1(D2HS)/BGEF, RG10L1(D2HS)/BGEFU1,

RG10P1(G2HS)/BGEFU1，RG10L10(D2HS)/BGEF

3.0V( Dry batteries R03/LR03×2)

-5°C~60°C(23°F~140°F)

FIT BATTERIES

POINT REMOTE TOWARD UNIT

PRESS POWER BUTTON

SELECT MODE SELECT TEMPERATURE

SELECT FAN SPEED

5 4

My Mode Follow Me LED Turbo

Ioniser

Swing

Timer

SelfClean

Mode On/Off Fan

Sleep

AUTO

COOL

DRY

HEAT

FAN

HIGH

MED

LOW

SETTEMPERATURE

AUTO

COOL

DRY

HEAT

FAN

AU-100%

TIPS FOR USING REMOTE CONTROL

NOTES FOR USING REMOTE CONTROL

• The remote control must be used within 8

meters of the unit.

The unit will beep when remote signal is

received.

Curtains, other materials and direct sunlight

can interfere with the infrared signal receiver.

Remove batteries if the remote will not be

used more than 2 months.

•

Inserting and Replacing Batteries

Your air conditioning unit may come with two

batteries(some units). Put the batteries in the

remote control before use.

Slide the back cover from the remote control

downward, exposing the battery compartment.

Insert the batteries, paying attention to match

up the (+) and (-) ends of the batteries with

the symbols inside the battery compartment.

Slide the battery cover back into place.

BATTERY NOTES

For optimum product performance:

•

Do not mix old and new batteries, or

batteries of different types.

•

Do not leave batteries in the remote control

if you don’t plan on using the device for more

than 2 months.

BATTERY DISPOSAL

Do not dispose of batteries as unsorted

municipal waste. Refer to local laws for proper

disposal of batteries.

The device could comply with the local national

regulations.

In Canada, it should comply with

CAN ICES-3(B)/NMB-3(B).

In USA, this device complies with part 15 of the

FCC Rules. Operation is subject to the following

two conditions:

(1) This device may not cause harmful interference,

and

(2) this device must accept any interference

received, including interference that may

cause undesired operation.

This equipment has been tested and found to

comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits

are designed to provide reasonable protection

against harmful interference in a residential

installation. This equipment generates, uses and

can radiate radio frequency energy and, if not

installed and used in accordance with the

instructions, may cause harmful interference to

radio communications. However, there is no

guarantee that interference will not occur in a

particular installation. If this equipment does cause

harmful interference to radio or television reception,

which can be determined by turning the equipment

off and on, the user is encouraged to try to correct

the interference by one or more of the following

measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment

and receiver.

Connect the equipment into an outlet on a circuit

different from that to which the receiver is

connected.

Consult the dealer or an experienced radio/TV

technician for help.

Changes or modifications not approved by the

party responsible for compliance could void

user’s authority to operate the equipment.

Handling the Remote Controller

Buttons and Functions

Before you begin using your new air conditioner, make sure to familiarize yourself with its remote

control. The following is a brief introduction to the remote control itself. For instructions on how to

operate your air conditioner, refer to the How to Use Basic Functions section of this manual.

ON/OFF

Turns the unit on or off. MODE

TIMER

Eco Intelligent eye

HUMIDITY

LED

Turbo

ECO/GEAR

Scrolls through operation modes

as follows: AUTO



COOL



DRY HEAT FAN

FAN SPEED

SWING

Model:

Increases temperate in

0.5°C (1°F) increments.

Max. temperature is

30°C (86°F).

NOTE: Press together &

buttons at the same time

for 3 seconds will alternate

the temperature display

between the °C & °F.

TEMP

RG10L(G2HS)/BGEF and RG10L(G2HS)/BGEFU1(Fresh feature is not available)

RG10L1(G2HS)/BGEF,RG10L1(G2HS)/BGEFU1

RG10L10(G2HS)/BGEF(20-28 C/68-82 F)

Used to confirm the selected functions.

Used to detect the people

activities in the room to save

energy.

Decreases temperature

in 0.5 C(1 F) increments.

Min. temperature is

O O

16 C(60 F).

urns indoor unit’s LED display

and air conditioner buzzer on

and off, which create a comfortable

and quiet environment.

Adjust the room humidity during

Dry operation in a range of

35%~85%. Press this button to

increase the humidity in 5%

increments.

NOTE: After setting, the humidity

settings will display on the screen.

Set timer to turn unit on or off

Press this button to enter the

energy efficient mode in a

sequence of following:

ECO GEAR(75%)

GEAR(50%)

mode ECO ......

Selects fan speeds in the

following order:



20%

60%40% 80% 100%.





Press the TEMP or button

to increase/decrease the fan

speed in 1% increments.

Enables unit to reach preset

temperature in shortest possible time.

Previous setting

SET

Scrolls through operation

functions as follows:

Breeze away( )

clean( ) Fresh( )

Sleep( ) Follow Me( )

AP mode ( ) Breeze

Active







The selected symbol will

flash on the display area,

press the OK button to

confirm.

away( ) .......

Starts and stops the horizontal

louver movement. Hold down

for 2 seconds to initiate vertical

louver auto swing feature.

NOTE: HEAT mode is not supported

by the cooling only appliance.

ON/OFF

Turns the unit on or off. MODE

TIMER

Intelligent eye function

HUMIDITY

LED

Turbo

ECO/GEAR

Scrolls through operation modes

as follows: AUTO



COOL



DRY HEAT FAN

FAN SPEED

SWING

Model:

Increases temperate in

0.5°C (1°F) increments.

Max. temperature is

30°C (86°F).

NOTE: Press together &

buttons at the same time

for 3 seconds will alternate

the temperature display

between the °C & °F.

TEMP

RG10P(G2HS)/BGEF and RG10P(G2HS)/BGEFU1(Fresh feature is not available)

RG10P1(G2HS)/BGEF,RG10P1(G2HS)/BGEFU1

Used to select wind flow follow

people feature or wind flow away

from people feature.

Decreases temperature

in 0.5 C(1 F) increments.

Min. temperature is

O O

16 C(60 F).

Turns indoor unit’s LED display

and air conditioner buzzer on

and off, which create a comfortable

and quiet environment.

Adjust the room humidity during

Dry operation in a range of

35%~85%. Press this button to

increase the humidity in 5%

increments.

NOTE: After setting, the humidity

settings will display on the screen.

Set timer to turn unit on or off

Used to confirm the selected functions.

Press this button to enter the

energy efficient mode in a

sequence of following:

ECO GEAR(75%)

GEAR(50%)

mode ECO ......

Selects fan speeds in the

following order:



20%

60%40% 80% 100%.





Press the TEMP or button

to increase/decrease the fan

speed in 1% increments.

Enables unit to reach preset

temperature in shortest possible time.

Previous setting

SET

Scrolls through operation

functions as follows:

Fresh( )

Sleep( ) Follow

AP mode ( )

Self clean( )

Self clean.....



Me( )



The selected symbol will

flash on the display area,

press the OK button to

confirm.

Starts and stops the horizontal

louver movement. Hold down

for 2 seconds to initiate vertical

louver auto swing feature.

NOTE: HEAT mode is not supported

by the cooling only appliance.

ON/OFF

Turns the unit on or off. MODE

TIMER

Eco Intelligent eye

HUMIDITY

LED

Turbo

ECO/GEAR

Scrolls through operation modes

as follows: AUTO



COOL



DRY HEAT FAN

FAN SPEED

SWING

Model:

Increases temperate in

0.5°C (1°F) increments.

Max. temperature is

30°C (86°F).

NOTE: Press together &

buttons at the same time

for 3 seconds will alternate

the temperature display

between the °C & °F.

TEMP

RG10L(D2HS)/BGEF and RG10L(D2HS)/BGEFU1(Fresh feature is not available)

RG10L1(D2HS)/BGEF,RG10L1(D2HS)/BGEFU1

RG10L10(D2HS)/BGEF(20-28 C/68-82 F)

Used to confirm the selected functions.

Used to detect the people

activities in the room to save

energy.

Decreases temperature

in 0.5 C(1 F) increments.

Min. temperature is

O O

16 C(60 F).

Turns indoor unit’s LED display

and air conditioner buzzer on

and off, which create a comfortable

and quiet environment.

Adjust the room humidity during

Dry operation in a range of

35%~85%. Press this button to

increase the humidity in 5%

increments.

NOTE: After setting, the humidity

settings will display on the screen.

Set timer to turn unit on or off

Press this button to enter the

energy efficient mode in a

sequence of following:

ECO GEAR(75%)

GEAR(50%)

mode ECO ......

Selects fan speeds in the

following order:



20%

60%40% 80% 100%.





Press the TEMP or button

to increase/decrease the fan

speed in 1% increments.

Enables unit to reach preset

temperature in shortest possible time.

Previous setting

SET

Scrolls through operation

functions as follows:

Breeze away( )

clean( ) Fresh( )

Sleep( ) Follow Me( )

AP mode ( ) Breeze

Active







The selected symbol will

flash on the display area,

press the OK button to

confirm.

away( ) .......

Starts and stops the horizontal

louver movement. Hold down

for 2 seconds to initiate vertical

louver auto swing feature.

NOTE: HEAT mode is not supported

by the cooling only appliance.

Information are displayed when the remote controller is power up.

Transmission Indicator

MODE display

TIMER ON display

FAN SPEED display

TIMER OFF display

Silence feature

display

ECO display

GEAR display

LOCK display

Horizontal louver swing

display(some units)

Vertical louver auto

swing display

TURBO mode display

Not applicalbe for

this unit

Temperature/Timer/Fan speed

display

Active clean feature display

Fresh feature display

Sleep mode display

Follow me feature display

Wireless control feature display

(some units)

Low battery detection display(If flashes)

Note:

All indicators shown in the figure are for the purpose of clear presentation. But during the actaul

operation, only the relative function signs are shown on the display window.

Remote Screen Indicators

Displays when LOCK feature

is activated.

Silence

LOW

MED

HIGH

AUTO

Lights up when remote

sends signal to indoor

unit

Displays selected fan speed:

Displays the current

including:

mode,

2%-20%

21%-40%

41%-60%

61%-80%

81%-100%

This fan speed can not be

adjusted in AUTO or DRY

mode.

Displays when ECO

feature is activated

Displays when GEAR

feature is activated

Displays the set temperature

by default, or fan speed or

timer setting when using

TIMER ON/OFF functions.

Temperature range:

16-30 C/60-86 F

Timer setting range:

0-24 hours

Fan speed setting range:

Humidity setting range:

AU -100%

35% -85%

This display is blank when

operating in FAN mode.

   

(20-28 C/68-82 F)

(Model dependent)

Breeze Away display

ECO intelligent eye display

(some units)

Not applicable for this unit

Wind flow follow people

(some units)

MODE

How to Use Basic Functions

AUTO Mode

COOL or HEAT Mode

DRY Mode

Select AUTO mode Set your desired temperature

NOTE:

1. In AUTO mode,

the unit will automatically select the COOL, FAN, or HEAT function based on

the set temperature.

2. In AUTO mode, fan speed can not be set.

Turn on the air conditioner

Select DRY mode Set your desired temperature Turn on the air conditioner

FAN Mode

Select FAN mode Turn on the air conditioner

Select COOL/HEAT mode Set the temperature Turn on the air

conditioner

Set the fan speed

NOTE: In DRY mode, fan speed can not be set since it has already been automatically controlled.

NOTE: In FAN mode, you can’t set the temperature. As a result , no temperature displays in remote screen.

Before operation, please ensure the unit is plugged in and power is available.

ATTENTION

MODE

Setting the TIMER

TIMER ON setting

TIMER OFF setting

TIMER ON & OFF setting(example)

TIMER ON/OFF - Set the amount of time after which the unit will automatically turn on/off.

Press TIMER button to initiate

the ON time sequence. Press Temp. up or down button for

for multiple times to set the desired

time to turn on the unit.

Press Temp. up or down button for

for multiple times to set the desired

time to turn off the unit.

NOTE:

1. When setting the TIMER ON or TIMER OFF, the time will increase by 30 minutes increments with each

press, up to 10 hours. After 10 hours and up to 24, it will increase in 1 hour increments. (For example,

press 5 times to get 2.5h, and press 10 times to get 5h,) The timer will revert to 0.0 after 24.

2. Cancel either function by setting its timer to 0.0h.

Point remote to unit and wait 1sec,

the TIMER ON will be activated.

Press TIMER button to initiate

the OFF time sequence. Point remote to unit and wait 1sec,

the TIMER OFF will be activated.

Current

time 1PM

2:00PM 3:00PM 4PM 5PM 6PM

Timer starts Unit turns

Unit turns

OFF

2.5 hours later

5 hours later

3:30PM

Example: If current timer is 1:00PM,

to set the timer as above steps, the

unit will turn on 2.5h later (3:30PM)

and turn off at 6:00PM.

ON/OFF

MODE

FAN

SHORT

CUT

TIMERON

TIMEROF

TEMP

SLEEP

1sec

ON/OFF

MODE

FAN

SHORT

CUT

TIMEROF

TEMP

SLEEP

ON/OFF

MODE

FAN

SHORT

CUT

TIMEROF

TEMP

SLEEP

ON/OFF

MODE

FAN

SHORT

CUT

TIMERON

TIMEROF

TEMP

SLEEP

1sec

xn xn

x10

Keep in mind that the time periods you set for both functions refer to hours after the current time.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Carrier Fernbedienung Handbücher

Carrier

Carrier rg05 Bedienungsanleitung

Carrier

Carrier 40VM900003 Fehlerbehebungshandbuch

Carrier

Carrier SYSTEM PILOT 33PILOT-01 Bedienungsanleitung

Carrier

Carrier 40 series Bedienungsanleitung

Carrier

Carrier EU-OSK105 Bedienungsanleitung

Carrier

Carrier NTC Bedienungsanleitung

Carrier

Carrier RG10B2/BGEF Bedienungsanleitung

Carrier

Carrier Infrared Remote 2 Bedienungsanleitung

Carrier

Carrier NTC-IR2 Bedienungsanleitung

Carrier

Carrier Cavius 9001 Bedienungsanleitung

Carrier

Carrier OSK102 Bedienungsanleitung

Carrier

Carrier RG67V/BGEF Bedienungsanleitung

Carrier

Carrier Aquasnap Plus 33AW-RC1 Bedienungsanleitung

Carrier

Carrier RG56V Series Bedienungsanleitung

Carrier

Carrier 33TB-AC01 Bedienungsanleitung

Carrier

Carrier RG56/BGEF-CA Bedienungsanleitung

Carrier

Carrier SYSTXCCITW01-A Infinity Bedienungsanleitung

Carrier

Carrier WTC-IR-LB Bedienungsanleitung

Carrier

Carrier RG10L1/BGEF Bedienungsanleitung

Carrier

Carrier RG10A2/BGEF Bedienungsanleitung

Carrier

Carrier 33CSPGMR-01 Bedienungsanleitung

Carrier

Carrier RBC-AMS54E-UL Bedienungsanleitung

Carrier

Carrier RG67N/BGEF Bedienungsanleitung

Carrier

Carrier RG67V/BGEF Bedienungsanleitung

Beliebte Fernbedienung Handbücher anderer Marken

Panasonic

Panasonic EUR7622KB0 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beo4 Bedienungsanleitung

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung

Multiplex

Multiplex PROFI TX 9 Bedienungsanleitung

One Remote

One Remote RMB4 Bedienungsanleitung

FUTABA

FUTABA 9ZAP - PART2 Bedienungsanleitung

HR Matic

HR Matic HR MULTI 3 Bedienungsanleitung

Yamaha

Yamaha ACC-GNRST-30-20 Bedienungsanleitung

EisSound

EisSound KBSOUND Bedienungsanleitung

Marantz

Marantz RC101 Bedienungsanleitung

Conrad

Conrad FS20 TC6 Bedienungsanleitung

Anritsu

Anritsu MP1777A Bedienungsanleitung

Niles

Niles WVC100 Fehlerbehebungshandbuch

RCA

RCA RCU1300 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BEO6 Bedienungsanleitung

GE 94901 Bedienungsanleitung

Onbon

Onbon YQ1-75 Bedienungsanleitung

FUTABA

FUTABA R7108SB Montageanleitung