Casio CFX-9970G Bedienungsanleitung
Dual Graph
Dual Graph lets you split the display between two different
screens, which you can then use to draw different graphs at the
same time. Dual Graph gives you valuable graph analysis
capabilities.
• You should be familiar with the contents of “8-3 Graph Function
Operations” before reading this chapter.
11-1 Before Using Dual Graph
11-2 Specifying the Left and Right View Window
Parameters
11-3 Drawing a Graph in the Active Screen
11-4 Displaying a Graph in the Inactive Screen
Chapter
11
168
P.7
P.112
11-1 Before Using Dual Graph
1. From the Main Menu, enter the GRAPH Mode. Next, display the set up screen
and specify “Graph” for Dual Screen.
2. Press J.
• For further details about the function key menu at the bottom of the display, see
“8-1 Before Trying to Draw a Graph”.
• 8,192 bytes of memory are used whenever you set the Dual Screen setting to
“Graph”.
kk
kk
kAbout Dual Graph Screen Types
The screen on the left side of the display is called the
active screen
, and the graph
on the left side of the display is called the
active graph
. Conversely, the right side
is the
inactive screen
, which contains the
inactive graph
. Any function that you
execute while using Dual Graph is always applied to the active graph. To execute
a function on the right-side inactive graph, you must first make it active by moving
it into the active screen.
Active Screen
Actual graph drawing is done here.
Inactive Screen
Use the inactive screen to make copies of active screen graphs, and for the result of
Zoom operations.
• Indicators appear to the right of the formulas in the function memory list to tell
where graphs are drawn with Dual Graph.
Indicates inactive graph (on right side of
display)
Indicates graph drawn on both sides of display
Performing a draw operation with the function marked “ R” in the above example
screen causes the graph to be drawn on the right (inactive) side on the display.
The function marked “ B” is drawn on both sides of the graph.
Pressing 1(SEL) while one of the function’s is highlighted would causes its
“R” or “ B” indicator to be cleared. A function without an indicator is drawn as
the active graph (on the left side of the display).
169
Before Using Dual Graph 11 - 1
11-2 Specifying the Left and Right View Window
Parameters
You can specify different View Window parameter for the left and right sides of the
graph display.
uu
uu
uTo specify View Window parameters
Press !3 (V-Window) to display the View Window parameter setting screen
for the active (left side) graph.
•{INIT}/{TRIG}/{STD} ... View Window {normal initialization}/{trigonometric
initialization}/{standardization}
•{STO}/{RCL} ... View Window setting {store}/{recall}
•{RIGHT}/{LEFT} ... {active (left)}/{inactive (right)} screen View Window setting
swap
• Use the procedures described under “View Window (V-Window) Settings” to
input parameter values.
• Use the following key operations to change to different screens while inputting
View Window parameters for the left and right side screens.
While the View Window parameter setting screen for the active graph is shown:
• 6(RIGHT) ....displays the inactive graph View Window parameter setting
screen
While the View Window parameter setting screen for the inactive graph is
shown:
•6(LEFT) ......displays the active graph View Window parameter setting
screen
P.115
P.116
P.113
170
11-3 Drawing a Graph in the Active Screen
You can draw graphs only in the active screen. You can then copy or move the
graph to the inactive screen.
uu
uu
uDrawing a graph in the active screen
Example To draw the graph of y= x(x+ 1) (x– 1)
Use the following View Window parameters:
Xmin = –2 Ymin = –2
Xmax = 2 Ymax = 2
Xscale = 0.5 Yscale = 1
Input the function.
v(v+b)(v-b)
Store the function.
w
Draw the graph.
6(DRAW) or w
171
11-4 Displaying a Graph in the Inactive Screen
There are two methods you can use to display a graph in the inactive screen. You
can copy a graph from the active screen to the inactive screen, or you can move
the graph from the active screen to the inactive screen. In both cases, you must
first draw the graph in the left-side active screen.
kk
kk
kBefore Displaying a Graph in the Inactive Screen
After drawing a graph in the active screen, press K, and the Dual Graph
function menu appears at the bottom of the display.
• {COPY} ... {copies active graph to inactive screen}
• {SWAP} ... {switches active screen and inactive screen}
• {PICT} ... {picture function}
kk
kk
kCopying the Active Graph to the Inactive Screen
Example To draw the graph for y= x(x+ 1) (x– 1) on the active screen
and the inactive screen
Use the following View Window parameters:
Active (Left) Screen Inactive (Right) Screen
View Window parameters View Window parameters
Xmin = –2 Ymin = –2 Xmin = –4 Ymin = –3
Xmax = 2 Ymax = 2 Xmax = 4 Ymax = 3
Xscale = 0.5 Yscale = 1 Xscale= 1 Yscale = 1
Assume that the function being graphed is stored in memory area Y1.
Draw the graph in the active screen. Copy the graph to the inactive
6(DRAW) (right) screen.
K1(COPY)
• The graph is reproduced using the inactive screen View Window parameters.
P.139
172
kk
kk
kSwitching the Contents of the Active and Inactive Screens
Switch the screens.
K2(SWAP)
• Note that using 2(SWAP) to switch the screens also switches their View
Window parameters.
kk
kk
kDrawing Different Graphs on the Active Screen and
Inactive Screen
Example To draw the graphs of the following functions on the screens
noted:
Active Screen: y= x(x+ 1) (x– 1)
Inactive Screen: y= 2x2– 3
Use the View Window parameters shown below.
Active (Left) Screen Inactive (Right) Screen
View Window parameters View Window parameters
Xmin = –4 Ymin = –5 Xmin = –2 Ymin = –2
Xmax = 4 Ymax = 5 Xmax = 2 Ymax = 2
Xscale = 1 Yscale = 1 Xscale= 0.5 Yscale = 1
Assume that the functions being graphed are stored in memory areas Y1 and Y2.
Select the function for the graph that you want to end up in the inactive (right)
screen. 1(SEL)
Draw the graph in the active screen.
6(DRAW)
11 - 4 Displaying a Graph in the Inactive Screen
173
Swap the screens so the graph is on the inactive (right) screen.
K2(SWAP)
Select the function for the graph that you want in the now-empty active (left)
screen.
A1(SEL)
Draw the graph.
6(DRAW)
• At this point, you could perform a copy operation and superimpose the active
graph over the inactive graph.
K1(COPY)
• Pressing !6 (G↔T) lets you switch between display of the active and
inactive graphs, using the entire display for each.
!6(G↔T)
!6(G↔T)
!6(G↔T)
Displaying a Graph in the Inactive Screen 11 - 4
174
kk
kk
kOther Graph Functions with Dual Graph
After drawing a graph using Dual Graph, you can use the trace, zoom, sketch and
scroll functions. Note, however, that these functions are available only for the
active (left) graph. For details on using these functions, see “8-6 Other Graphing
Functions”.
• To perform any of the above operations on the inactive graph, first move the
inactive graph to the active screen.
• The graph screen will not scroll while a trace operation is being performed on
the active graph.
The following shows some example operations using the zoom function.
Example 1 To use box zoom to enlarge the graph of y= x(x+ 1) (x– 1)
Use the following View Window parameters for the active graph.
Xmin = –2 Ymin = –2
Xmax = 2 Ymax = 2
Xscale = 0.5 Yscale = 1
Assume that the function is already stored in memory area Y1.
Press 6(DRAW) or wto draw the graph.
!2(Zoom)1(BOX)
• Use the cursor keys to move the pointer to
one of the corners of the box and then press
w.
• Use the cursor keys to move to the opposite corner of the box and then press
wto enlarge the graph.
• The zoom operation changes the View Window parameters of the inactive
screen, so the graph in the inactive screen is cleared.
11 - 4 Displaying a Graph in the Inactive Screen
P.128
Andere Handbücher für CFX-9970G
21
Inhaltsverzeichnis
Andere Casio Kalkulator Handbücher
Casio
Casio fx-260 Einrichtungshandbuch
Casio
Casio FX-9750GII - SOFTWARE VERSION 2-00 Bedienungsanleitung
Casio
Casio SF-5580RS Bedienungsanleitung
Casio
Casio ALGEBRA FX 2.0 Bedienungsanleitung
Casio
Casio DC-150A Bedienungsanleitung
Casio
Casio fx-CG50 Installationshandbuch
Casio
Casio ALGEBRA FX 2.0 Bedienungsanleitung
Casio
Casio fx-350TL Bedienungsanleitung
Casio
Casio fx-100AU PLUS Bedienungsanleitung
Casio
Casio FX-85SA Bedienungsanleitung
Casio
Casio FX-500 Bedienungsanleitung
Casio
Casio SL-315TE Bedienungsanleitung
Casio
Casio FX-7700GE Bedienungsanleitung
Casio
Casio FR-1011S Bedienungsanleitung
Casio
Casio FX-CG10 Bedienungsanleitung
Casio
Casio fx-7400G PLUS Bedienungsanleitung
Casio
Casio ALGEBRA FX 2.0 Plus Gebrauchsanweisung
Casio
Casio ALGEBRA FX 2.0 Plus Bedienungsanleitung
Casio
Casio SF-8350 Fehlerbehebungshandbuch
Casio
Casio fx-7400G PLUS Bedienungsanleitung
