Casio EX-843 Bedienungsanleitung

SERVICE MANUAL

ELECTRONIC CASH REGISTER

V-R200

(EX-843)

JUL. 2016

Ver.3 : Jun. 2017

V-R200 / VER.1

CONTENTS

IMPORTANT NOTICE....................................................................................... P. 1

PRODUCT SPECIFICATIONS.......................................................................... P. 8

DIAGNOSTIC OPERATION............................................................................. P. 12

DISASSEMBLY/ASSEMBLY ........................................................................... P. 33

CIRCUIT DIAGRAM......................................................................................... P. 59

EXPLODED VIEW/PARTS LIST...................................................................... P. 63

V-R200 / VER.1

– 1 –

IMPORTANT NOTICE

Safety Precautions................................................................................... P. 2

Precautions for Use ................................................................................. P. 3

Information

3-1. Basic Operation .................................................................................................... P. 5

3-2. SD/SDHC memory card ........................................................................................ P. 7

Repair Information

When the main PCB is replaced with a spare part one.

• Since an OS is already installed on the spare part main PCB, update the OS to an appropriate

version as required.

Refer to: Diagnostic operation 2. UPDATING the OS

• Write the serial number.

Refer to: Diagnostic operation 1-6. Checking and Registering the Serial Number

When the IOC PCB is replaced with a spare part one.

• Firmware is already installed on it.

• The ﬁrmware version is conﬁrmed at power on and, if necessary, it is automatically updated.

• UUID setting is not required.

When the CASE ASSY/FRONT is replaced with a spare part one.

• Carry out the touch panel calibration.

Refer to: Diagnostic operation 1-4. Touch panel calibration

To carry out the Diagnostic operation, a dedicated application is needed to be installed

beforehand.

NOTE: After completion of the test, make sure to uninstall the test application.

V-R200 / VER.1

– 2 –

Safety Precautions

* Caution

LAN Conenector

Ethernet (LAN) Connector:

Not used to a telecommunication network

To Prevent malfunctions caused by the weak batteries, charge the memory

protection batteries for over 6-hours.

1. Before installation, initialize the terminal and leave it power on over 6-hours.

2. After the terminal is repaired or checked, you must leave it power on over 6-hours.

BATTERIES HANDLING PRECAUTIONS

1. Do not use old and new batteries mixed together, or batteries at different charge levels.

This may cause leakage of battery ﬂuid and heat generation.

2. Load a set of three new batteries at being care of their polarity.

V-R200 / VER.1

– 3 –

Precautions for Use

Read the following items thoroughly and use this product properly. CASIO bears no responsibility whatsoever

for malfunction or damage caused by handling not following below contents. Please note that it will also result in

charged repair, and actual cost required for repair will be charged, even if it is within the warranty period.

Installation Location

Do not place in a hot or dusty location, or in any location exposed to oily smoke or water. Never store or leave in

following locations. This could erase the memory and cause a malfunction or result in deformation of the case.

0 Temperature of 0 °C or lower

0 Inside vehicles in summer

0 Close to air conditioner

0 Under direct sunlight

0 Temperature of 40 °C or higher

Avoid using this product in following locations.

0 Outdoor

0 Close to equipment that will become hot such as range, electrical heater, etc.

0 Location exposed to water or steam

0 Location with severe change in environment such as temperature, humidity, etc.

0 Location where corrosive gas or saline matter is generated

0 Location where dirt or dust is generated

0 Location with vibration

0 Location prone to static electricity

Other

0 Prepare separate AC power supply from the power line for motor, ice maker, microwave oven, etc., which may

generate noise.

0 Do not touch the power switch with wet hands. This may result in electrical shock.

0 Wipe thoroughly with dry cloth, etc., when there is any water droplet on the device.

0 Do not use any volatile chemical such as thinner, benzine, cosmetics, etc., for cleaning. Wipe with dry soft cloth

when this product gets dirty. The display section may be scratched when scuffed strongly with a cloth.

0 When the capacity of the internal memory protection battery is insufﬁcient ant there is no power supply available

due to a power outage, malfunction or other reason, the memory content might be erased.

0 Contact the dealer or the CASIO service representative around 5 years after purchase to replace the battery (this

time depends on how the product is used).

V-R200 / VER.1

– 4 –

Take Advance Notice of the Following

0 The content of this manual may be changed without prior notice due to improvement or speciﬁcation change of

the product.

0 Please note that CASIO bears no responsibility for damage, loss of proﬁt, or any claim from third party due to

loss or change of data caused by usage, malfunction, or repair of this product.

0 The copyright for this manual and all rights related to the software described in this manual are the property of

CASIO Computer Co., Ltd. The unauthorized reproduction of this manual in whole or part is prohibited without

the written permission of CASIO.

0 The screen or illustration used in this manual may be different from the actual product. The keys and icons are

described in simpliﬁed manner.

0 Weld Line

The line on the exterior of the product is called “weld line”, which is created at the time of plastic forming, and it is

not a crack or a scratch. This will not interrupt the usage.

Trademark Registration

SD, SDHC, microSD and microSDHC are trademarks of SD-3C, LLC.

V-R200 / VER.1

– 5 –

Information

3-1. Basic Operation

(1) General information

Fig. 1

Maintenance switch

Power switch

Power lamp

Reset switch

Fig. 2

• The power switch is pressed.

• When touching the touch panel.

• An alarm occurs.

• The reset switch is pressed.

¨Reboot without shutdown

• The power switch is pressed.

• No operation is done for a certain period of time.

• The power switch is pressed.

• The reset switch is pressed.

¨Reboot without shutdown

• The power switch is held down more than 5 sec.,

then choose "Power off".

• The maintenance switch is held down more than 5 sec.

OFF state

Power lamp: OFF

ON state

Power lamp: Green

Sleep state

Power lamp: Orange

NOTE: Power lamp: Red (Insufﬁcient capacity of the internal memory backup battery)

Do not shutdown the power supplied to the product or unplug the power cord.

NOTE: After taking out a product from carton box, connect AC adaptor to the product then leave it more than

6hours to charge internal memory buck up battery for full charge.

V-R200 / VER.1

– 6 –

(2) Shutdown procedure

There are two ways to shut down.

0Shutting down by the power switch

Press and hold the power switch until “Power off” / “force tablet reboot” appears.

Select “Power off”“OK”.

Fig. 3 Fig. 4

0Shutting down by the maintenance switch

Press and hold the maintenance switch until “Pwer off” appears.

Fig. 5

V-R200 / VER.1

– 7 –

3-2. SD/SDHC memory card

(1) Recommended SD/SDHC memory card

SanDisk Corporation Transcend Information, Inc.

SDSDB-016- SDSDUL-016- TS16GSDU1

Fig. 6

(2) Mounting the SD/SDHC memory card

SD/SDHC memory card is automatically mounted when it is inserted. If it has been unmounted due to

incorrect operation, mount it again.

Select “Settings”“Storage”“Mount SD card”.

Fig. 7

(3) Unmounting the SD/SDHC memory card

Select “Settings”“Storage”“Unmount SD card”“OK”.

Fig. 8

– 8 –

V-R200 / VER.1

PRODUCT SPECIFICATIONS

YSpeciﬁcations List

Main display

Type 10.4 SVGA color TFT LCD

Resolution 800 × 600

Color *1 Max. 16.77 million colors

Backlight White LED

Other Power tilt function (15° to 75°)

Touch panel

Method 4-wire resistive ﬁlm

Size 10.4 inch

Sub display

Resolution 32 × 160 dot (20 single-byte characters, 2 lines)

Backlight 2 colors (emerald green, white)

Printer

Print method Thermal printer

Print speed *1 Max. 120 mm/sec.

Paper roll Thermal recording paper, width 58 mm or 80 mm,

external diameter 80 mm or smaller

Paper cut-off Automatic cutter

Memory protection *2

Battery Nickel-metal hydride rechargeable battery

Memory holding *3 Approximately 1 hour (used at 25 °C)

Battery life *4 5 years (used at 25 °C)

Charge time Full charge in 6 hours (used at 25 °C)

Time holding Approximately 30 days (used at 25 °C)

Power supply/

power consumption

120 V ac ±10 V 50/60 Hz 0.64 A (Operating) 0.2A (Standby)

220 V to 240 V ac ±10 V 50/60 Hz 0.36 A (Operating) 0.11A (Standby)

External interface

Side of display SD/SDHC memory card slot x 1

Back of the device COM port x 3, LAN port x 1, USB port x 1, DC jack x 1

Water proof performance IP53 level (main display only) *5

Temperature/humidity

(when in use) 0°C to 40°C/20% to 85% RH

External dimensions W 395 mm x D 237 mm x H 229 mm

(With maximum tilt angle) (Not including protruding parts)

Weight Approximately 4.0 kg

*1: These ﬁgures indicate the performance level of the hardware. The actual colours and speed vary depending on

the application in use.

*2: The internal battery is a consumable item. Contact the dealer or the CASIO service representative around

5 years after purchase to replace the battery (this time depends on how the product is used). Memory protection

may not operate properly if the battery becomes depleted.

*3: After 1 hour of disconnect power, the product will shut itself down. To turn the power ON, press the power

switch after power recovery.

*4: With a battery usage frequency of once per month.

*5: The speciﬁcations here are test values, and are not guaranteed values.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Casio Kasse Handbücher

Casio

Casio 200cR Bedienungsanleitung

Casio

Casio PCR-204 Montageanleitung

Casio

Casio PCRT275 - Cash Register w/ 15 Depts Bedienungsanleitung

Casio

Casio V-R100 Bedienungsanleitung

Casio

Casio TE-2200 Bedienungsanleitung

Casio

Casio TE-8000F Series Bedienungsanleitung

Casio

Casio SE-C450 Bedienungsanleitung

Casio

Casio SE-G1 Bedienungsanleitung

Casio

Casio PCR T48S - Cash Register Bedienungsanleitung

Casio

Casio SE-S2000 Handbuch

Casio

Casio TK-950 Bedienungsanleitung

Casio

Casio V-R100 Bedienungsanleitung

Casio

Casio TK-6500 Series Bedienungsanleitung

Casio

Casio CE-280 Montageanleitung

Casio

Casio CE-280 Montageanleitung

Casio

Casio PCR-T465 Bedienungsanleitung

Casio

Casio TE-4000F Series Bedienungsanleitung

Casio

Casio TK-810 Montageanleitung

Casio

Casio PCR T265 - Electronic Cash Register Bedienungsanleitung

Casio

Casio CE-3700 Bedienungsanleitung

Casio

Casio CE-300 (EX-247) Bedienungsanleitung

Casio

Casio SE-S10 Bedienungsanleitung

Casio

Casio CE-4000 Montageanleitung

Casio

Casio PCR-360 Montageanleitung

Beliebte Kasse Handbücher anderer Marken

Royal

Royal 480nt Bedienungsanleitung

Olivetti

Olivetti ECR 8200 S Bedienungsanleitung

TEC

TEC TEC FS-3600 Bedienungsanleitung

Integrated System Laboratory

Integrated System Laboratory ISL 4006 Bedienungsanleitung

Sam4s

Sam4s ER-380 Fehlerbehebungshandbuch

Sharp

Sharp XE-A206 Stücklistenhandbuch

Samsung

Samsung ER 5215 Bedienungsanleitung

Toast

Toast Toast Bedienungsanleitung

Sharp

Sharp XE-A130 Kurzanleitung

TEC

TEC MA-600-1 series Bedienungsanleitung

QUORION

QUORION CR 1200 Bedienungsanleitung

Olivetti

Olivetti ECR 7700 LD eco Plus Bedienungsanleitung

Sharp

Sharp XE-A137-WH Operation Kurzanleitung

Sharp

Sharp XE-A203 - Cash Register Thermal Printing Graphic Logo... Bedienungsanleitung

TEC

TEC TEC MA-1060 Bedienungsanleitung

ELCOM

ELCOM Euro-2100TE Bedienungsanleitung

American Changer

American Changer CLASSIC Series Bedienungsanleitung

Sam4s

Sam4s ER-180 Bedienungsanleitung