CATSKILL 1448 Bedienungsanleitung

CRAFTSMEN, INC.

Assembly Instructions

Model 1448

A. Assembly uses the Bastion System; a simple yet rugged compression

fastening system.

B. This unit is made of solid North American hardwood and has a factory

applied oil finish. See the enclosed booklet for care instructions.

C. Directions (left/right, front/back) are given as facing the front of an

assembled unit.

P/N: TT1448B

(1) Table Top 48” x 24” x 2”

P/N: SLS1448B

(2) Slated Shelf 43-3/4” x 18” x 1-3/4”

P/N: DF1448B

(1) Drawer Front 39-3/8” x 5-3/8” x 3/4”

P/N: DBK1448B

(1) Drawer Back 38-3/8” x 4-1/2” x 3/4”

P/N: TBK1448B

(1) Top Back Brace 39-1/2” x 5-1/2” x 3/4”

P/N: TSB1448B

(2) Top Side Brace 14-1/2” x 5-1/2” x 3/4”

P/N: DSL1448B

(1) Drawer Side Left

14” x 4-1/2” x 3/4”

P/N: DSR1448B

(1) Drawer Side Right

14” x 4-1/2” x 3/4”

P/N: DB1448B

(1) Drawer Bottom 37-5/8” x 15-5/8” x 5.2mm

GLIDE-1448B

14”

P/N: FL/BRleg1448B

(2) Front Left/Back Right Legs

33-1/2” x 2-3/16” x 2-3/16”

P/N: FR/BLleg1448B

(2) Front Right/Back Left Legs

33-1/2” x 2-3/16” x 2-3/16”

Model 1448

Parts List

P/N: GSB1448B

(2) Glide Support Brace

14-1/2” x 2” x 3/4”

P/N: L-bracket1448B

(4) L-Brackets

(10)

P/N: Leveler1448

(4) 7/8 Leveler

P/N: Pipe1448B

(1) Nickel Plated Towel Bar Handle

32” x 5/8”

P/N: EndCap1448B

(2) Pipe End Cap

5/8”

(12)

(14)

P/N: SKRU 7/16 panhead (8)

7/16 #6 PANHEAD SCREW

P/N: Pipe Holder 1448B

(2) Pipe Holder

P/N: T-Nut1448

(4) T-Nut

Model 1448

Parts List

Continued

P/N: SKRU 5/8 #6 (8)

5/8 #6 WOOD SCREW

Bastion Assembly

INSTRUCTIONS FOR BASTIONS

ILLUSTRATION ONLY. See Steps 1 & 3

for bastion placement for this unit.

STEP 1

ASSEMBLE SIDE PANELS

A. Each side panel consists of two (2) legs, one (1) top side

brace and one (1) glide support brace. When assembled,

diagonal legs will be the same (i.e. Front Right/Back Left &

Front Left/Back Right). Side panels are identical when

assembled -- the drawer glides will determine left and right

sides.

B. Tap a 3/4” pin in each end of the top side braces. Take

each of the 4 legs and install one (1) bastion post per leg, on

the side of the leg which also has two (2) pin holes for the

glide support sticks. Locate post holes. Tap posts in with

hammer until threads engage wood; turn posts down until

the solid shaft hits the wood (all threads are into wood), then

back post out until the hole in the post is perpendicular to

the long length of the leg (about 1/2 turn).

C. Lay out Front Left leg, one (1) top side brace and back

left leg as in Illustration 1A. Note the two pilot holes for the L

brackets are along the top inside of the top side brace.

D. Take the top side brace and drop a barrel-shaped bronze

bastion nut into the nut access hole as illustrated. Threaded

end of the nut faces out. Insert front left leg post into the

hole in the end of the brace, through the side of the barrel

nut, until the hole in the post can be seen through the

threaded end of the nut. Insert the set screw into the nut

and tighten down. The tip of the set screw will seek the

center of the bastion post as it is tightened, leaving a tight

joint. If the joint is loose, check to make sure the set screw is

not cross-threaded or that the post is out too far (not

threaded into leg deep enough.) See Instructions for

Bastions illustrations on page 3 for clarrification of assembly.

E. Insert two 3/4” pins into each end of the glide support

brace. Insert brace pins into the holes on the inside of the

left front leg as illustrated (4 pilot holes out).

F. Attach Back Left leg in same manner.

G. Repeat for other side panel.

Table top “L” Bracket holes

nut access holes

not used

holes for

shelves

TOP SIDE BRACE

Bastion Post

GLIDE SUPPORT BRACE

Glide Support Steel Pin Holes

Illustration 1A

Illustration 1B

Illustration 1C

PREPARE SIDE

ASSEMBLIES FOR BACK

BRACES

The Top Back Brace utilizes

the Bastion system for

attachment. Place the

Bastion posts into their

positions on the back legs

only of both side assemblies.

Bastion Post

Positions for

Top Back Brace

7/16”

inch

STEP 3

ATTACH BACK BRACE

A. You may find it easiest to attach the back brace and shelves by inverting the island. Attach the back brace

with bastions to the right and left side assembly.

STEP 4

ATTACH SHELVES

A. It is recommeded to get a friend to help hold the shelves in place as you attach them using 1-1/4” #8 screws.

STEP 5

TABLE TOP PREPARATION & ATTACHING

Attach four (4) “L” brackets (using 5/8” #6 screws) to the bottom side of the table top. Note the proper position

of the “L” brackets.

Illustration 7-A

Make sure the round

hole is used to attach

the L-Bracket to the

bottom of the Table Top.

STEP 6

ATTACH TABLE TOP

Utilizing the “L” brackets, attach the table top, using

5/8” #6 screws.

STEP 7

INSERT LEVELER FEET

A. Hammer the threaded T-bolt into the predrilled hole on the bottom of

each leg. Screw the leveler into the T-bolt. Height of each of four levelers

can be adjusted to stablize entire unit.

Leg

STEP 8

Assemble Drawers

A. Attach the Drawer Back to the Left and Right Drawer Sides with four 1 ¼”#8 Screws. Make

sure the slots that run the length of the Sides are aligned with the slot in the Drawer Back to

accept the Drawer Bottom.

B. Slide in Drawer Bottom, best side up,

Illustration 8A

Andere Handbücher für 1448

Andere CATSKILL Rack & Stand Handbücher

CATSKILL

CATSKILL 7237 Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung