CDVI GALEO/W Bedienungsanleitung

Edition 10/2006 G0301FR0266V01

MOUNTING KIT

Qty Description Photo Utilisation

M4x10 tamper screw GALEO Mounting screw

T20 spanner For the M4x10 screw

M4x30 mounting screws 2 * keypad back plate

2 * Remote Controller

2 Caps GALEO cap

S5 plastic anchor 2 * keypad back plate

2 * Remote Controller

05D 680K varistor For the lock

2 Wiring sealed caps Cable to the controller

Dimensions: 110 x 75 x 15 mm

CABLE

Description

Red 12V DC (+)

Black 0V

Brown Buzzer command input

Green Data 0

White Data 1

Blue Clock

Gray 0V common

GALEO/W

ILLUMINATED ONLINE KEYPAD

26 BIT OUTPUT FORMAT, CLOCK &

DATA and CDVI OUTPUT FORMAT

INSTALLATION MANUAL

IP 64 DM

Edition 10/2006 G0301FR0266V01

I. GENERAL INFORMATION

A. Description

Input voltage 12V DC

12-digit illuminated keypad keys

EEPROM memory storage

User code in 4, 5 or 6 digits

Buzzer

ST1 jumper for programming

B. Default values

Illumination duration: 10 seconds

User code lenght: 5 digits

26 bit wiegand output

Buzzer disabled

C. Audible Signal

1 short beep keypad powered and key presses

1 long beep data computing in programming

2 short beeps Entry or Exit from programming

4 short beeps data computing error

D. Code Length

The user code must be in 4, 5 or 6 digits.

All the keypad keys can be used to program a user code except the B key.

Enter the user code and then B to validate the code.

E. Consumption

80mA in 12 VDC (permanent illuminated keys)

II. PROGRAMMING

A. Entry in programming

1. Turn off the power. Put the switch to ON. Put back the power.

2. Two beeps are emitted to confirm entry in programming.

The command control of the buzzer is not possible in programming mode.

B. Illumination duration

1. Enter in programming.

2. Enter A0 to program the illumination duration. One beep is emitted. Enter the time in

seconds – 10 for 10 seconds to 99 for 99 seconds or enter 00 for a permanent illumination.

One beep is emitted to confirm the illumination duration.

Edition 10/2006 G0301FR0266V01

3. Remove the ST1 jumper. Two beeps are emitted to confirm exit from programming.

C. Output format

1. Enter in programming.

2. Press A1 to enter in the output format menu. One beep is emitted.

Press 1 to select 26-bit wiegand output format

Press 2 to select CDVI output format

Press 3 to select ISO Track 2 output format

One beep is emitted to confirm programming.

3. Remove the ST1 jumper. Two beeps are emitted to confirm exit from programming.

C. Code length

1. Enter in programming mode.

2. Press A2 to enter in the code length setting menu. One beep is emitted. Press 4 for a 4-digit

user code, press 5 for a 5-digit user code or press 6 for a 6-digit user code. One beep is

emitted to confirm programming.

3. Remove the ST1 jumper. Two beeps are emitted to confirm exit from programming.

4 beeps indicate a data computing error.

D. Audible signal

The audible signal is always enabled in programming mode.

In factory default, the buzzer is disabled when pressing a key. To enable the buzzer:

1. Enter in programming mode.

2. Press A3. One beep is emitted. Press 0 to disable the audible signal. Press 1 to enable the

audible signal. One beep is emitted to confirm programming.

3. Remove the ST1 jumper. Two beeps are emitted to confirm exit from programming.

E. External control of the buzzer

The buzzer can be activated from an external input. The control is done with a logic signal on the

input.

Buzzer enabledBuzzer disabled Buzzer disabled

Edition 10/2006 G0301FR0266V01

F. 26-bit wiegand format

Interfaçage

The output format is 26-bit Wiegand (Signals: DATA1, DATA0 and CLOCK)

Output signal in open collectors (pull up of 2.2K in +5V)

26-bit hexadecimal output format

The frame is made of 26-bit and built as follow:

First parity: 1-bit – even parity for the first 12-bit

User Code: 3 half of a byte represent the code entered

Each byte is transferred from bit 7 to bit 0.

Second parity: 1-bit – odd parity for the last 12-bit

Bit 1 Bit 2 … bit 25 bit 26

Even parity on bit 2…bit13 Data (24 bits) Odd parity on bit 14…bit 25

Example a 4-digit code: 1350 then B

1 0000 0000 0001 0011 0101 0000 1

Parity 1 0 0 1

3 5 0 Parity 2

The code is transmitted in hexadecimal: 001350

Example a 5-digit code: 71350 then B

0 0000 0111 0001 0011 0101 0000 1

Parity 1 0 7 1 3 5 0 Parity 2

The code is transmitted in hexadecimal: 071350

Example a 6-digit code: 671350 then B

0 0110 0111 0001 0011 0101 0000 1

Parity 1 6 7 1 3 5 0 Parity 2

The code is transmitted in hexadecimal: 671350

Parity 1: 0 if the number of 1 in bit 2 to bit 13 is even

1 if the number of 1 in bit 2 to bit 13 is odd

Chronograms

\CLOCK

\DATA1

\DATA0

0 logic 1 logic

50s 50s2ms 2ms

Edition 10/2006 G0301FR0266V01

Parity 2: 0 if the number of 1 in bit 14 to bit 25 is odd

1 if the number of 1 in bit 14 to bit 25 is even

G. CDVI Format

This format is owned by CDVI. This format is compatible with other CDVI products ( PROMI, UCA3 ).

H. ISO 7811 Track 2 Format

SS Characters ES

LRC

SS = start sentinel Hex B

ES = end sentinel Hex F

LRC = Ou Exclusif de tous les caractères de la trame (including SS and ES)

The code length is set at 8 digits:

In 4 digits – 00001234

In 5-digits – 00012345

In 6-digits - 00123456

Each digit is made of 5 bits (4 bits data + 1 bit parity)

Characters

B4 B3 B2 B1 Parity

0 0 0 0 0 1

1 0 0 0 1 0

2 0 0 1 0 0

3 0 0 1 1 1

4 0 1 0 0 0

5 0 1 0 1 1

6 0 1 1 0 1

7 0 1 1 1 0

8 1 0 0 0 0

9 1 0 0 1 1

A 1 0 1 0 1

B = SS 1 0 1 1 0

C 1 1 0 0 1

D = FD 1 1 0 1 0

E 1 1 1 0 0

F = ES 1 1 1 1 1

/Présence

/Data

/Clock

Edition 10/2006 G0301FR0266V01

III. MOUNTING INSTRUCTIONS

Drill (bit Ø5mm) 2 mounting holes

(minimum depth 35mm) and the cable

hole.

Insert the S5 2 plastic anchors in the

holes.

Mount the back plate with the M4x30

screws.

Insert the cable of the GALEO®inside

to cable hole.

Place the GALEO®on the back plate

and slide it from up to down. Make sure

that the mounting bracket is properly

set with the GALEO.

Use the M4x10 screw to close the

keypad (T20 spanner). Place the screw

cap.

To mount the remote controller on the wall use the plastic bracket.

GALEO

Andere Handbücher für GALEO/W

Inhaltsverzeichnis

Andere CDVI Tastenfeld Handbücher

CDVI

CDVI GALEO 4.0 - Bluetooth Bedienungsanleitung

CDVI

CDVI CAA Bedienungsanleitung

CDVI

CDVI CAASE Bedienungsanleitung

CDVI

CDVI Digicode Series Bedienungsanleitung

CDVI

CDVI KCINBT Bedienungsanleitung

CDVI

CDVI Galeo Bedienungsanleitung

CDVI

CDVI Digicode DGA Bedienungsanleitung

CDVI

CDVI Digicode Series Bedienungsanleitung

CDVI

CDVI Galeo Bedienungsanleitung

CDVI

CDVI GALEOR Bedienungsanleitung

CDVI

CDVI Digicode KCIN Bedienungsanleitung

CDVI

CDVI PROFIL100EINT Bedienungsanleitung

CDVI

CDVI GALEO/W Bedienungsanleitung

CDVI

CDVI GALEO 4.0 - Bluetooth Bedienungsanleitung

CDVI

CDVI Digicode PROFIL100EC Bedienungsanleitung

CDVI

CDVI DC100E Bedienungsanleitung

CDVI

CDVI KCIN Bedienungsanleitung

CDVI

CDVI GALEO/W Bedienungsanleitung

CDVI

CDVI PROFIL 100 EC Bedienungsanleitung

CDVI

CDVI GALEOR Bedienungsanleitung

CDVI

CDVI C2R Bedienungsanleitung

CDVI

CDVI GALEOR Bedienungsanleitung

CDVI

CDVI SUBLIM Bedienungsanleitung

CDVI

CDVI DGA Bedienungsanleitung

Beliebte Tastenfeld Handbücher anderer Marken

BFT

BFT SELETTO Bedienungsanleitung

Micro Id

Micro Id MP7G3BL Gebrauchsanweisung

WindowMaster

WindowMaster WLI 130 Bedienungsanleitung

ACT

ACT ACT PRO 1030 Bedienungsanleitung

Cardin

Cardin SSB Series Bedienungsanleitung

Harman Kardon

Harman Kardon KP 1 Bedienungsanleitung

Chamberlain

Chamberlain KPR2000 Benutzerhandbuch

CYP

CYP CR-KP1 Bedienungsanleitung

Aeware

Aeware k-35 Series Referenzhandbuch

Aritech

Aritech CS-175 Series Bedienungsanleitung

GE NetworX NX-1600E Series Bedienungsanleitung

Lenze AC Tech

Lenze AC Tech MC SERIES Bedienungsanleitung

Burg Wächter

Burg Wächter secuENTRY 7711 Bedienungsanleitung

Aeware

Aeware in.k450 Bedienungsanleitung

Lenze

Lenze EPM-H410 Bedienungsanleitung

Toshiba

Toshiba RKP007Z Bedienungsanleitung

Gemini

Gemini GEM-DXK1 KEYPAD Bedienungsanleitung

Russound

Russound MDK-C5 Betriebsanleitung