CEECO HOB-313-DD-48 Bedienungsanleitung

HOB-313-DD[R,B]-650-520-CAC4.04-42&NVR1.0-ISSUE4.0

SERVICE MANUAL

FOR

MODEL HOB-313-DD-48

TWO-BUTTON AUTOMATIC DIALING

PANEL TELEPHONE

EQUIPPED WITH CAC4.04-42 FIRMWARE AND

NVR1.0 MEMORY CONVERSION PCB

Serving the Telephone Industry Since 1930

Communication Equipment 519 West South Park St.

& Engineering Company Okeechobee, FL. 34972

Voice: 863-357-0798

Fax: 863-357-0006

ISSUE 4.0

CEECO

Communication Equipment & Engineering Company

PROPRIETARY

IMPORTANT INFORMATION

FOR

CUSTOMER

Please fill in before you continue.

The following information is necessary when calling CEECO for assistance.

MODEL NUMBER

MODEL HOB-313-DD-48 EQUIPPED

WITH CAC4.04-42 FIRMWARE

SERIAL NUMBER

DATE MANUFACTURED

LOCATION INSTALLED

For us to better serve you, please have this information available when calling for

technical support.

CEECO

Communication Equipment & Engineering Company

519 West South Park Street

Okeechobee, FL 34972

(863) 357-0798 Voice

(863) 357-0006 Fax

ISSUE 4.0

CEECO

Communication Equipment & Engineering Company

PROPRIETARY

TABLE OF CONTENTS

SECTION PAGE

1.0 INTRODUCTION................................................................................................. 4

2.0 GENERAL............................................................................................................. 4

3.0 PROGRAMMING................................................................................................ 5

PROGRAMMING CONTINUED…................................................................... 6

4.0 TESTING/OPERATION ..................................................................................... 6

5.0 RECOMMENDED TOOLS AND TEST EQUIPMENT.................................. 6

6.0 INSTALLATION INSTRUCTIONS .................................................................. 7

7.0 SPECIFICATIONS............................................................................................... 8

8.0 PARTS LIST ......................................................................................................... 9

9.0 FCC NOTICE...................................................................................................... 10

10.0 REPAIR AND RETURN INFORMATION..................................................... 11

11.0 WARRANTY POLICY...................................................................................... 12

12.0 MODULAR JACK DIAGRAM......................................................................... 13

13.0 DIAGRAM........................................................................................................... 14

ISSUE 4.0

CEECO

Communication Equipment & Engineering Company

PROPRIETARY

1.0 INTRODUCTION

The practices in this manual provide installation and maintenance information for

the Model HOB-313-DD-48 Two-Button Automatic Dialer Panel Telephone,

equipped with CAC4.04-42 software.

For information not included in this manual, please call or write:

CEECO

Customer Service

519 West South Park Street

Okeechobee, FL 34972

(863) 357-0798

2.0 GENERAL

The CEECO Model HOB-313-DD-48 Telephone, equipped with CAC4.04-42

Firmware, is a stainless steel, microprocessor-based, coinless panel phone

designed to withstand abuse and fraudulent call attempts. The transmitter is

muted during periods of dial tone eliminating the use of hand held dialers.

Attempts to hookswitch dial a number will cause the microprocessor to go “on

hook” until the attempt has ended. Incoming calls may be allowed or blocked

depending upon the programming. If programmed to block incoming calls, the

phone will drop the line upon receipt of an incoming call. Programming is

accomplished via the DTMF keypad inside the telephone housing.

This model telephone is intended for use with the open-faced, weather-resistant

housing, P/N 331-HOB

The phone also comes with a custom handset, which is blue in color and has a

54” long armored cord.

ISSUE 4.0

CEECO

Communication Equipment & Engineering Company

PROPRIETARY

3.0 PROGRAMMING

3.1 Connect the telephone to a working telephone line or a DTMF test set.

3.2 Remove the panel phone from the housing, and locate the two plastic

mini-jumpers on the edge of the printed circuit board and move them to

the “ON” position, as depicted on the last page of this manual.

3.3 Lift the handset and wait for dial tone before beginning programming.

Programming is accomplished by way of the DTMF keypad. The

programming can be accomplished in one continuous sequence without

having to stop or perform any measures between programming sections. It

is important to be slow and deliberate when pressing the keys during

programming. A missed or partial tone will result in improper

programming.

3.4 Utilizing the keypad, enter # 9 7. This will clear all memory locations.

You must wait for two beeps, indicating the memory has been cleared, in

order to proceed. This may take up to two seconds.

3.5 Enter # 0 0, followed by 0, followed by 1to allow incoming calls or 0to

block incoming calls, followed by 1.

Example: Entering #00 0 1 1 would program the phone to allow

incoming calls, whereas entering #00 0 0 1 would program the

phone to block incoming calls.

*If programmed to block incoming calls, the phone will still ring as usual.

When the incoming call is answered, the telephone will drop the line,

thus blocking the call, and no conversation will take place.

3.6 Enter #01 followed by the desired number to be automatically dialed by

the Red Button.

Example: Entering #015551212 will program the telephone to

automatically dial the number 555-1212, when the red button is pressed.

Enter #02 followed by the desired number to be automatically dialed by

the Black Button.

Example: Entering #025875430 will program the telephone to

automatically dial the number 587-5430, when the black button is pressed.

ISSUE 4.0

CEECO

Communication Equipment & Engineering Company

PROPRIETARY

PROGRAMMING CONTINUED…

Notes: -The # sign represents the # key of the keypad and must actually

be dialed.

-Each of the numbers programmed above may be up to eleven

(11) digits in length.

3.7 Programming is now completed. Hang up the phone and return the mini-

jumpers to the “OFF” position, as depicted on the last page of this

manual. The phone is now ready for Testing/Operation. Mount the HOB

housing in the intended location and return the panel phone to the housing.

4.0 TESTING/OPERATION

4.1 Connect the phone connected to the DTMF test set or working telephone

line and lift the handset. When dial tone is received, the transmitter is

muted and the telephone waits for one of the three buttons to be pressed.

4.2 Select the number to be dialed by pressing the desired button on the

telephone (Red or Black). The number programmed into the appropriate

button location will automatically dial and a normal telephone

conversation may take place. When the call is completed, hang up the

phone by returning the handset to the cradle. All three buttons should

operate as such.

4.3 If the telephone was programmed to block incoming calls in section 3.5,

the phone will still ring as usual. When the incoming call is answered, the

telephone will drop the line, thus blocking the call, and no conversation

will take place.

5.0 RECOMMENDED TOOLS AND TEST EQUIPMENT

DTMF Test Set

Volt/Ohm Meter

1/4" Nut Driver

Flat Blade Screw Driver

Security Tool, CEECO Part Number 301-037

ISSUE 4.0

CEECO

Communication Equipment & Engineering Company

PROPRIETARY

6.0 INSTALLATION INSTRUCTIONS

6.1 Using a 301-037 security tool (sold separately) loosen and remove the

security screws.

6.2 The security tool is for a standard 5/32" button head screw generally used

on the framework of the phone booths.

6.3 Separate the telephone assembly from the mounting or housing.

Mountings or housings should be installed as is appropriate for each

particular item and installation. Be sure that installation is done in

accordance with all applicable laws and codes.

6.4 Run the inside station wire through the mounting or housing and terminate

on to the CEECO-provided RJ11C terminal block.

6.5 The use of a gas tube station protector is recommended. The station

ground should not exceed 50 ohms.

6.6 Plug the modular line cord from the telephone assembly into the RJ11C

terminal block.

6.7 Dress the line cable away from hardware, which might cause damage to

the cable. Secure the telephone assembly by installing and tightening the

security screws.

6.8 When servicing the phone, be sure the PC board does not contact metal

parts, otherwise permanent damage may occur to the board.

*****WARNING*****

A. Never install telephone wiring during a lightning

storm.

B. Never install telephone jacks in wet locations unless

the jack is specifically designed for wet locations.

C. Never touch uninsulated telephone wires or

terminals unless the telephone line has been

disconnected at the network interface.

D. Use caution when installing or modifying telephone

lines.

ISSUE 4.0

CEECO

Communication Equipment & Engineering Company

PROPRIETARY

7.0 SPECIFICATIONS

INPUT POWER: C.O. Line powered

LOOP CURRENT: 23ma. min. 80ma. max.(48 VOLT LOOP)

IMPEDANCE: 600 ohms

SIGNALING: DTMF, 70ms tone, 50ms spacing

OUTPUT: -8.0 to -10.0dbm

HEARING AID

COMPATIBLE: Meets EIA standards

ENVIRONMENTAL: Temperature 0C to 50C

Humidity 20%-90% non-condensating

PROGRAMMING: Via DTMF keypad.

TELEPHONE PANEL: 14 ga Stainless Steel

DIMENSIONS: 7 1/6Wide x 11 1/4High x 4 1/4Deep

(Handset on hook).

MOUNTING: . Vertical Surface Mount

WEIGHT: Approximately 4 lb.

HOB HOUSING: Painted/Silk-Screened CRS

MEMORY RETENTION: Lithium Battery - Long Life

WEIGHT: Approximately 17 Pounds

FCC REGISTRATION: BW88T7-13823-TE-T

UL LISTED NO.: 6OF5

RINGER EQUIVALENCY: 0.4A

TYPE JACK: RJ11C

FIRMWARE: CAC4.04-42

ISSUE 4.0

CEECO

Communication Equipment & Engineering Company

PROPRIETARY

8.0 PARTS LIST

QUANTITY PART NUMBER DESCRIPTION

1 301-004-54-B Armored Cord Handset-Blue

1 301-006 Ringer

1 301-009 Network

1 301-581 Tongue & Bracket Assembly

1 301-589 Magnetic Hookswitch

1 301-018 Modular Line Cord

1 301-054 Modular Connector (RJ11C)

1 650-570 Network Cable

1 650-520 MCRK-2 Board

4 9024 Security Screws

1 331-HOB-B Weather-resistant Housing

ACCESSORIES:

1 301-064 Security Tool

ISSUE 4.0

CEECO

Communication Equipment & Engineering Company

PROPRIETARY

9.0 FCC NOTICE

9.1 FCC REGISTRATION AND REPAIR INFORMATION

Your new telephone has been registered with the Federal Communication

Commission (FCC) in accordance with Part 68 of its rules. The FCC

requires that you be advised of certain requirements involving the use of

this telephone.

9.2 CONNECTION WITH THE NATIONWIDE TELEPHONE NETWORK

The FCC requires that you connect this telephone to the Nationwide

Telephone Network through a registered jack provided by the Telephone

Company in your area. This jack is a modular outlet, which you can order

from your local telephone company.

9.3 NOTIFICATION TO THE TELEPHONE COMPANY

Before connecting this telephone, the FCC requires that you notify your

local telephone company business office. The number is in the front of

your phone book.

Tell them:

The "line" to which you will connect the telephone (that is, your phone

number) and the telephone's FCC registration number and ringer

equivalence number. These numbers are listed in Section 7.0.

The FCC further requires that you notify your local telephone company

when permanently disconnecting this telephone.

Inhaltsverzeichnis

Andere CEECO Telefon Handbücher

CEECO

CEECO SSP-373-D Bedienungsanleitung

CEECO

CEECO SSW-321-F-IVC-C-M Bedienungsanleitung

CEECO

CEECO WPP-531-D2 Bedienungsanleitung

CEECO

CEECO WPP-531-D-ADA-STROBE Bedienungsanleitung

CEECO

CEECO SSP-371-D Bedienungsanleitung

CEECO

CEECO MHW-341-X Bedienungsanleitung

CEECO

CEECO WPP-331-F Bedienungsanleitung

CEECO

CEECO WPP-531-D2-ADA-VA-R-SB24VDC Bedienungsanleitung

CEECO

CEECO SSP-560-F Bedienungsanleitung

CEECO

CEECO WPP-333-D Bedienungsanleitung

CEECO

CEECO SSP-350-X-130 Bedienungsanleitung

CEECO

CEECO SSW-321-D Bedienungsanleitung

CEECO

CEECO BLC-303-F Bedienungsanleitung

CEECO

CEECO SSP-363-D Bedienungsanleitung

CEECO

CEECO SSP-571-D Bedienungsanleitung

CEECO

CEECO SSP-570-D Bedienungsanleitung

CEECO

CEECO SSP-363-E Bedienungsanleitung

CEECO

CEECO SSP-363-F Bedienungsanleitung

CEECO

CEECO SSW-321-Dr1 Bedienungsanleitung

CEECO

CEECO SSC-303-D Bedienungsanleitung

CEECO

CEECO WPP-531-DD Bedienungsanleitung

CEECO

CEECO HOB-331-F Bedienungsanleitung

CEECO

CEECO SSP-351 series Bedienungsanleitung

CEECO

CEECO SSW-321-F Bedienungsanleitung

Beliebte Telefon Handbücher anderer Marken

GE 2-9480 Bedienungsanleitung

Geemarc

Geemarc PHOTOPHONE 155 Bedienungsanleitung

D-Link

D-Link DWR-720/PW Bedienungsanleitung

Interquartz

Interquartz Gemini IQ333 Bedienungsanleitung

SSS Siedle

SSS Siedle HT 840-0 Bedienungsanleitung

Motorola

Motorola TITANIUM Bedienungsanleitung

Panasonic

Panasonic ICX Bedienungsanleitung

LG H870DS Bedienungsanleitung

Samsung

Samsung GT-I9500 Bedienungsanleitung

AT&T

AT&T Trimline 205 Bedienungsanleitung

Selta

Selta zenyth 600 Bedienungsanleitung

Doro

Doro AFTI 20 Bedienungsanleitung

UNIQCELL

UNIQCELL A1 Bedienungsanleitung

Panasonic

Panasonic KX Series Bedienungsanleitung

Jabra

Jabra SP5050 - Bluetooth hands-free Speakerphone Bedienungsanleitung

BT Decor 425 Bedienungsanleitung

NEC

NEC SV8500 Bedienungsanleitung

Teledex

Teledex PEARL Bedienungsanleitung