CEECO SSP-571-D Bedienungsanleitung

SSP-571-D (FORMERLY 579)-ADA-AA-VA-SPK1.07UNVL-ISSUE4.0

SERVICE MANUAL

FOR

MODEL SSP-571-D

(FORMERLY MODEL SSP-579-D)

HANDS FREE PANEL TELEPHONE

EQUIPPED WITH SPK1.07 UNVL FIRMWARE

WITH OPTIONAL:

•ADA FEATURE

•AUTO-ANSWER FEATURE

•VOICE-ANNOUNCEMENT FEATURE

Serving the Telephone Industry Since 1930

Communication Equipment 519 W South Park Street

& Engineering Company Okeechobee, FL 34972

Voice: 863-357-0798

Fax: 863-357-0006

ISSUE 4.0

CEECO

Communication Equipment & Engineering Company

PROPRIETARY

IMPORTANT INFORMATION

FOR

CUSTOMER

Please fill in before you continue.

The following information is necessary when calling CEECO for assistance.

MODEL NUMBER MODEL SSP-571-D-ADA-AA-VA,

EQUIPPED WITH SPK1.07UNVL

FIRMWARE

SERIAL NUMBER

DATE MANUFACTURED

LOCATION INSTALLED

For us to better serve you, please have this information available when calling for

technical support.

CEECO

Communication Equipment & Engineering Company

519 W South Park Street

Okeechobee, FL 34972

863-357-0798- telephone

863-357-0006- facsimile

[email protected]

www.ceeco.net

ISSUE 4.0

CEECO

Communication Equipment & Engineering Company

PROPRIETARY

TABLE OF CONTENTS

SECTION PAGE

1.0 INTRODUCTION................................................................................................... 4

2.0 GENERAL............................................................................................................... 5

3.0 PROGRAMMING .................................................................................................. 6

PROGRAMMING CONTINUED…..................................................................... 7

PROGRAMMING CONTINUED…..................................................................... 8

PROGRAMMING CONTINUED…..................................................................... 9

3.10 AUTO-ANSWER .................................................................................................... 9

3.11 VOICE ANNOUNCEMENT ................................................................................. 9

PROGRAMMING CONTINUED…................................................................... 10

4.0 TESTING/OPERATION ..................................................................................... 10

TESTING/OPERATION CONTINUED… ........................................................ 11

4.7 REMOTE MONITORING .................................................................................. 11

5.0 RECOMMENDED TOOLS AND TEST EQUIPMENT .................................. 11

6.0 INSTALLATION NOTES AND ASSEMBLY INSTRUCTIONS ................... 12

6.9 OVER-VOLTAGE PROTECTION DIAGRAM: ............................................. 13

7.0 SPECIFICATIONS............................................................................................... 14

8.0 PARTS LIST ......................................................................................................... 15

9.0 FCC NOTICE........................................................................................................ 16

10.0 REPAIR AND RETURN INFORMATION ....................................................... 17

11.0 WARRANTY POLICY ........................................................................................ 18

12.0 AUTO-ANSWER DIAGRAM ............................................................................. 19

13.0 PROGRAMMING JUMPER DIAGRAM ......................................................... 20

ISSUE 4.0

CEECO

Communication Equipment & Engineering Company

PROPRIETARY

1.0 INTRODUCTION

The practices in this manual provide installation and maintenance information for the

CEECO Model SSP-571-D-ADA-AA-VA Telephone, equipped with

SPK-1.07UNVL firmware.

The information in this manual is subject to change without notification.

For information not included in this manual, please call or write:

CEECO

Customer Service

519 W South Park Street

Okeechobee, FL 34972

863-357-0798- telephone

863-357-0006- facsimile

[email protected]

www.ceeco.net

ISSUE 4.0

CEECO

Communication Equipment & Engineering Company

PROPRIETARY

2.0 GENERAL

2.1 The CEECO Model SSP-571-D-ADA-AA-VA hands free telephone is a

sturdy, vandal resistant, Stainless Steel Speakerphone. Instead of a

hookswitch and handset, the SSP-571-D has a Press to start/Press to stop

(CALL) button for the initiation and termination of phone calls.

2.2 The telephone may be programmed to automatically dial (auto-dial) a

telephone number of up to eleven (11) digits in length.

2.3 The telephone may also be programmed to automatically dial a PBX or

other access number of up to eleven (11) digits in length.

2.4 The telephone provides an optional auto-answer feature, which allows

remote monitoring of the area in which the telephone is installed.

2.5 The telephone provides an optional voice announcement feature, which

allows a pre-recorded message (up to 10 sec.) to play when the receiving

party answers.

2.6 The telephone provides an optional ADA feature, which utilizes an LED

for visual recognition of the call progress. When the called party answers

the LED will turn GREEN after a maximum of four seconds, if the ADA

feature was activated during programming.

2.6 The microphone is muted during periods of dial tone to help guard against

the use of hand held dialers.

2.7 Incoming calls may be allowed or blocked depending on the

programming.

2.8 The telephone may be programmed to automatically disconnect a call after

a selected time period of 1-9 minutes.

2.9 Programming is accomplished via a separately supplied DTMF keypad.

ISSUE 4.0

CEECO

Communication Equipment & Engineering Company

PROPRIETARY

3.0 PROGRAMMING

NOTE: It is recommended that you ground yourself to prevent ESD

Damage to the PCB(s).

3.1 Connect the telephone to a working telephone line or a DTMF test set

before programming.

3.2 Locate the multicolor ribbon cable, extending from the Printed Circuit

Board, with a white connector hanging loosely. Locate the programming

keypad (provided separately), which has the mating end of the white

connector attached to it. Connect the keypad to the ribbon cable, by way

of the two connectors.

3.3 Move the mini-jumpers (located on the Printed Circuit Board) to the

"ON" position, as depicted on the last page of this manual.

3.4 Press the CALL button and wait for dial tone before programming any

digits.

3.5 It is important to be slow and deliberate when pressing the keys of the

programming keypad. A missed or partial tone could result in improper

programming.

NOTE:Once the “#" (pound) key has been entered you may get an

operator recording or a fast busy, please disregard and continue

programming.

3.6 Press the CALL button located on the front of the phone and utilize the

programming keypad to enter:

#97 #18# #19#

This will clear all field programmable memory.

3.7 Enter # 0 0 followed by a series of ten (10) Digits as selected from the

options on the following page. By entering 0 thru 9 into each of the 10

digits, the phone is customized for the particular installation. A selection

for all ten Digits must be entered in order for the phone to operate

properly.

ISSUE 4.0

CEECO

Communication Equipment & Engineering Company

PROPRIETARY

PROGRAMMING CONTINUED…

Digit 1:

0 Always 0 for this model.

Digit 2:

0 No incoming calls allowed.

1 Incoming calls allowed.

Digit 3:

0 No Conversation Time-Out.

1-9 Minutes Conversation Time-Out. (the call will automatically be terminated after the

selected number of minutes).

Digit 4:

0 Always 0 for this model.

Digit 5:

0 Always 0 for this model.

Digit 6:

0 No ADA Feature.

9 Activate ADA Feature

Digit 7:

0Always 0 for this model

Digit 8: (PBX Access – see section 3.9)

0 Do not dial PBX access number stored in Location #l8.

1Dial PBX access number stored in Location #18.

Digit 9:

0 Always 0 for this model.

Digit 10:

0 No Wink Detect.

1-9 Length of the Wink (l = 50ms incremental to 450ms – entering a 5is

recommended).

•Be sure to record your selections below for future reference:

#00 0 __ __ 0 0 __ 0 __ 0 __

1 2 3 4 5 6 7 8 9 10

ISSUE 4.0

CEECO

Communication Equipment & Engineering Company

PROPRIETARY

PROGRAMMING CONTINUED…

EXAMPLE:

Enter #00 0160000005

Phone will be set as follows:

DIGIT 1 .. ALWAYS 0

DIGIT 2 .. INCOMING CALLS ALLOWED

DIGIT 3 .. 6 MINUTE TIME OUT FOR EMERGENCY CALLS

DIGIT 4 .. ALWAYS 0

DIGIT 5 .. ALWAYS 0

DIGIT 6 .. ADA DEACTIVATED

DIGIT 7 .. ALWAYS 0

DIGIT 8 .. DO NOT DIAL PBX NUMBER STORED IN LOCATION#18

DIGIT 9 .. ALWAYS 0

DIGIT 10 . 250ms WINK

3.8 Enter # 1 9 followed by the desired auto-dial number. When the phone

is in operation and the CALL button is pressed, this auto-dial number will

automatically dial out. This number may be up to eleven (11) digits in

length.

#19 ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___

Example: Enter #195 5 5 1 2 1 2. This will program the phone to

automatically dial the number 555-1212, whenever the CALL button is

pressed.

3.9 If it is necessary for the telephone to automatically dial a PBX or other

access number, enter # 1 8 followed by the desired PBX access code or

number. When the phone is in operation and the CALL button is pressed,

this number will automatically dial out, followed by the auto-dial number.

There will be approximately a one (1) second pause between the dialing of

the two numbers. This number may be up to eleven (11) digits in length.

If this is not a desired feature, proceed to section 3.10.

Example: Enter #189. This will program the phone to automatically

dial the number 9, pause approximately one (1) second, and automatically

dial the auto-dial number, whenever the CALL button is pressed.

#18 ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___

ISSUE 4.0

CEECO

Communication Equipment & Engineering Company

PROPRIETARY

PROGRAMMING CONTINUED…

3.10 Auto-Answer

To program the auto-answer feature locate the 660-650 Printed Circuit

Board under the large (660-000) main printed circuit board. Refer to the

diagram on page 16 of this manual. Move the mini-jumper to the

desired ring count, from 1-9.

RING COUNT

0 No auto-answer

1 Answer after 1st ring

2 Answer after 2nd ring

3 Answer after 3rd ring

4 Answer after 4th ring

5 Answer after 5th ring

6 Answer after 6th ring

7 Answer after 7th ring

8 Answer after 8th ring

9Answer after 9th ring

The Remote Monitoring function associated with this auto-answer feature

will be explained in section 4.0 Testing/Operation.

3.11 VOICE ANNOUNCEMENT

•To record the voice announcement, press the CALL & HANGUP

button, and the phone will dial the preprogrammed number in location

#19.

•Ask the called party to put the phone on HOLD or keep quiet while

you get ready to record the message.

•Refer to the diagram on page 16 to locate the voice record switch on

the printed circuit board. Toggle the record switch to the ON

position. The phone's LED will turn red.

•Speak clearly and loudly into the microphone on the front of the

phone. The message can be up to ten (10) seconds in length.

•When finished, toggle the record switch to the OFF position. The

LED will turn off.

ISSUE 4.0

CEECO

Communication Equipment & Engineering Company

PROPRIETARY

PROGRAMMING CONTINUED…

3.12 When programming is finished, hang up the phone by pressing the

CALL button. Return the mini-jumpers to the "OFF" position. The

phone is now ready for Testing/Operation.

4.0 TESTING/OPERATION

4.1 Connect the telephone to a working telephone line.

4.2 To make a call, press the CALL button located on the front of the phone.

When dial tone is received, the transmitter is muted and the phone waits

for numbers to be dialed. The LED will illuminate RED at this time, and

the preprogrammed number(s) will dial out on the line.

4.3 When the called party answers the LED will turn GREEN after a

maximum of four seconds, if the ADA feature was activated (see section

3.7 Digit 6). Otherwise, the LED will remain RED during off-hook

periods. Any pre-recorded voice announcement will play at this time to

both the far end and the local user. Afterward, a normal speakerphone

conversation should be allowed.

4.4 When the call is complete, press the CALL button again to hang up. The

LED will go out and the call will be terminated.

4.5 If the user does not press the CALL button when he or she is done, the

phone will hang up after detecting a wink back from the far end, or when

the selected time-out period (see section 3.7 Digit 3) expires.

4.6 Place a call into the phone. If the phone was programmed to allow

incoming calls, answer the phone and the microphone should activate

within approximately three (3) seconds. A normal speakerphone

conversation should follow. If the phone was programmed not to allow

incoming calls, the microphone will not activate.

Andere Handbücher für SSP-571-D

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere CEECO Telefon Handbücher

CEECO

CEECO SSP-350-X-130 Bedienungsanleitung

CEECO

CEECO BLW-321-F Bedienungsanleitung

CEECO

CEECO WPP-331-D-M-IVC Bedienungsanleitung

CEECO

CEECO WPP-531-FD Bedienungsanleitung

CEECO

CEECO SSP-571-D Bedienungsanleitung

CEECO

CEECO SSW-321-F Bedienungsanleitung

CEECO

CEECO SSW-321-Xr1 Bedienungsanleitung

CEECO

CEECO WPP-531-X-ADA-STROBE Bedienungsanleitung

CEECO

CEECO IP-SSP-511- X Bedienungsanleitung

CEECO

CEECO BLC-303-F Bedienungsanleitung

CEECO

CEECO 403-F Bedienungsanleitung

CEECO

CEECO WPP-331-D-M Bedienungsanleitung

CEECO

CEECO MHD-341-D Bedienungsanleitung

CEECO

CEECO SSP-550-D Bedienungsanleitung

CEECO

CEECO SSP-570-D Bedienungsanleitung

CEECO

CEECO WPP-331-F Bedienungsanleitung

CEECO

CEECO SSP-561-D Bedienungsanleitung

CEECO

CEECO SSP-361-X Bedienungsanleitung

CEECO

CEECO Charge-A-Call BLC-303-1 Bedienungsanleitung

CEECO

CEECO MHW-341-X Bedienungsanleitung

CEECO

CEECO SSP-511-DD-ADA Bedienungsanleitung

CEECO

CEECO WPP-531-D2-ADA-VA-R-SB24VDC Bedienungsanleitung

CEECO

CEECO SSP-350-X Bedienungsanleitung

CEECO

CEECO SSW-321-F-IVC-C-M Bedienungsanleitung

Beliebte Telefon Handbücher anderer Marken

GE 2-9480 Bedienungsanleitung

Geemarc

Geemarc PHOTOPHONE 155 Bedienungsanleitung

D-Link

D-Link DWR-720/PW Bedienungsanleitung

Interquartz

Interquartz Gemini IQ333 Bedienungsanleitung

SSS Siedle

SSS Siedle HT 840-0 Bedienungsanleitung

Motorola

Motorola TITANIUM Bedienungsanleitung

Panasonic

Panasonic ICX Bedienungsanleitung

LG H870DS Bedienungsanleitung

Samsung

Samsung GT-I9500 Bedienungsanleitung

AT&T

AT&T Trimline 205 Bedienungsanleitung

Selta

Selta zenyth 600 Bedienungsanleitung

Doro

Doro AFTI 20 Bedienungsanleitung

UNIQCELL

UNIQCELL A1 Bedienungsanleitung

Panasonic

Panasonic KX Series Bedienungsanleitung

Jabra

Jabra SP5050 - Bluetooth hands-free Speakerphone Bedienungsanleitung

BT Decor 425 Bedienungsanleitung

NEC

NEC SV8500 Bedienungsanleitung

Teledex

Teledex PEARL Bedienungsanleitung