CEECO HOB-531-X Bedienungsanleitung

WPP(HOB)-531-X OR SSP-511-X-SPK1.07-ISSUE4.0

SERVICE MANUAL

FOR

MODEL WPP-531-X

WEATHERPROOF TELPHONE

MODEL HOB-531-X

WEATHER RESISTANT TELPHONE

MODEL SSP-511-X

STAINLESS STEEL PANEL TELEPHONE

WITH OPTIONAL ADA FEATURE

EQUIPPED WITH SPK1.07 FIRMWARE

Serving the Telephone Industry Since 1930

Communication Equipment 519 W South Park Street

& Engineering Company Okeechobee, FL 34972

Voice: 863-357-0798

Fax: 863-357-0006

ISSUE 4.0

CEECO

Communication Equipment & Engineering Company

PROPRIETARY

IMPORTANT INFORMATION

FOR

CUSTOMER

Please fill in before you continue.

The following information is necessary when calling CEECO for assistance.

MODEL NUMBER

MODEL WPP-531-X, HOB-531-X, OR

SSP-511-X EQUIPPED WITH SPK1.07

FIRMWARE.

SERIAL NUMBER

DATE MANUFACTURED

LOCATION INSTALLED

For us to better serve you, please have this information available when calling for

technical support.

CEECO

Communication Equipment & Engineering Company

519 W South Park Street

Okeechobee, FL 34972

863-357-0798- telephone

863-357-0006- facsimile

[email protected]

www.ceeco.net

ISSUE 4.0

CEECO

Communication Equipment & Engineering Company

PROPRIETARY

TABLE OF CONTENTS

SECTION PAGE

1.0 INTRODUCTION................................................................................................... 4

2.0 GENERAL............................................................................................................... 4

3.0 PROGRAMMING.................................................................................................. 5

PROGRAMMING CONTINUED......................................................................... 6

PROGRAMMING CONTINUED......................................................................... 7

4.0 OPERATION .......................................................................................................... 7

5.0 RECOMMENDED TOOLS AND TEST EQUIPMENT.................................... 7

6.0 INSTALLATION NOTES AND ASSEMBLY INSTRUCTIONS..................... 8

7.0 TESTING............................................................................................................... 10

8.0 SPECIFICATIONS............................................................................................... 11

9.0 PARTS LIST ......................................................................................................... 12

10.0 FCC NOTICE........................................................................................................ 13

11.0 REPAIR AND RETURN INFORMATION....................................................... 14

12.0 WARRANTY POLICY........................................................................................ 15

13.0 DIAGRAM............................................................................................................. 16

ISSUE 4.0

CEECO

Communication Equipment & Engineering Company

PROPRIETARY

1.0 INTRODUCTION

The practices in this manual provide installation and maintenance information for the

CEECO Model WPP-531-X Hands free Weatherproof Telephone, HOB-531-X Weather

Resistant Telephone, or Model SSP-511-X Stainless Steel Panel Telephone, equipped

with SPK1.07 firmware.

The information in this manual is subject to change without notification.

For information not included in this manual, please call or write:

CEECO

Customer Service

519 W South Park Street

Okeechobee, FL 34972

863-357-0798- telephone

863-357-0006- facsimile

[email protected]

www.ceeco.net

2.0 GENERAL

2.1 The CEECO Model WPP-531-X handsfree is a weatherproof telephone.

The Model HOB-531-X is a handsfree weather resistant telephone and the

SSP-311-X is the stainless steel panel telephone that fits in both the WPP

and the HOB housings. Instead of a hookswitch and handset, the

telephones have a Press to start/Press to stop button for initiation and

termination of phone calls. This Emergency button is provided for

automatic ring down applications. Ordinarily, the telephone can only be

used to receive calls. The telephone may, however, be used to initiate

calls if it is used in conjunction with external call equipment (i.e.

programmable switch, ring down circuit, etc…) Manual volume controls

for the microphone and speaker are provided inside the phones.

2.2 Incoming calls may be allowed or blocked depending on the

programming.

2.3 Programming is accomplished via the DTMF keypad.

ISSUE 4.0

CEECO

Communication Equipment & Engineering Company

PROPRIETARY

3.0 PROGRAMMING

3.1 Remove the front stainless steel panel by loosening the four security

screws with a security tool (sold separately) and remove them. Remove

the panel and attached telephone assembly.

3.2 Connect the telephone to a working telephone line or a DTMF test set.

3.2 Locate the pair of plastic mini-jumpers located near the edge of the

printed circuit board. Move them to the “ON” or innermost position, as

depicted on the last page of this manual.

3.3 Locate the programming keypad, which is either mounted on the back

panel or provided on the side. If the keypad is packaged separately, locate

the multicolored ribbon cable with white connector, which extends from

the PC Board of the phone. Connect the keypad to that connector.

3.4 Each programming location is accessed by dialing the "#" sign and the two

digit code, which corresponds to that location. The only valid program

locations for this phone is #00. The previous contents of the location are

automatically erased when the location code is dialed.

3.5 Press the “CALL & HANGUP” button and wait to hear dial tone.

3.6 Using the keypad, enter # 9 7 # 1 8 #. This will clear all user

programmable memory to begin programming.

3.7 Location "00" is the telephone options location. By entering a number of

1-9 into each of the 10 digits, the phone is customized for the particular

installation.

3.8 Enter #00 followed by ten digits, as selected on the next page. This “X”

model phone only offers selections for Digits 2, 3, and 10 on the next

page. It is recommended that a “5” be entered under Digit 10.

NOTE:

THIS EQUIPMENT IS TELEPHONE LINE POWERED.DURING PROGRAMMING THE CENTRAL

OFFICE OR PBX MAY RESPOND TO THE PROGRAMMING CODES WITH VARIOUS BUSY TONE,

REORDER TONE,RECORDINGS,ETC.THESE TONES AND RECORDINGS WILL HAVE NO

EFFECT ON THE PROGRAMMING.PLEASE IGNORE THEM.

ISSUE 4.0

CEECO

Communication Equipment & Engineering Company

PROPRIETARY

PROGRAMMING CONTINUED

LOCATION #00

Digit 1:

Always 0 for this model.

Digit 2:

0 No incoming calls allowed.

1 Incoming calls allowed.

Digit 3:

0 No time-out disconnect

1-9 Minutes time-out disconnect

Digit 4:

Always 0 for this model

Digit 5:

Always 1 for this model

Digit 6:

Always 0 for this model.

Digit 7:

Always 0 for this model

Digit 8:

Always 0 for this model

Digit 9:

Always 0 for this model

Digit 10:

00 No wink detect.

1-9 Length of the wink detect.

(1=50ms incremental to 450 ms. 5 is recommended).

Be sure to enter your selections below for future reference.

#00= 0 __ __ 0 1 0 0 0 0 5

DIGITS: 1 2 3 4 5 6 7 8 9 10

ISSUE 4.0

CEECO

Communication Equipment & Engineering Company

PROPRIETARY

PROGRAMMING CONTINUED

3.9 When you are finished programming, press the “CALL & HANGUP”

button to hang up the phone. Return the two plastic mini-jumpers to the

“OFF” or outermost position, as depicted on the last page of this manual.

Secure the telephone assembly in the housing. The phone is now ready for

use.

4.0 OPERATION

To receive a call, press the "EMER/CALL" button located on the front of the

phone, when the telephone rings. The LED (if provided) will illuminate red at this

time. In order to receive incoming calls the phone must have been programmed

with a “1” under Digit 2 in section 3.8 of this manual. When the call is answered,

a normal speakerphone conversation may take place. After the call is complete,

press the "EMER/CALL" button on the front of the panel again to hang up the

phone. If the user does not press the button on the front of the panel when he or

she is finished using the phone, then the phone will hang up after detecting a wink

(open switch interval) or the timer times out.

If the telephone has been mated with external call equipment, a call may also be

initiated by pressing the “EMER/CALL” button. The LED (if provided) will

illuminate red at this time. The external call equipment should direct the call as

intended and a normal speakerphone conversation may take place. After the call is

complete, press the "EMER/CALL" button on the front of the panel again to hang

up the phone. If the user does not press the button on the front of the panel when

he or she is finished using the phone, then the phone will hang up after detecting a

wink (open switch interval) or the timer times out.

5.0 RECOMMENDED TOOLS AND TEST EQUIPMENT

DTMF Test Set

Volt/Ohm Meter

CEECO Security Tool, 301-064

ISSUE 4.0

CEECO

Communication Equipment & Engineering Company

PROPRIETARY

6.0 INSTALLATION NOTES AND ASSEMBLY INSTRUCTIONS

6.1 Using a 301-064 security tool (sold separately), loosen and remove the

security screws.

6.2 The security tool is for a standard 5/32" button head screw generally used

on the framework of the phone booths.

6.3 Separate the faceplate assembly from the weatherproof housing by pulling

the faceplate forward.

6.4 Run the inside station wire into the enclosure and terminate on the RJ11C

terminal block inside, as depicted on the following page. The CEECO

provided terminal block (jack) must be used, as it contains required over-

voltage protection circuitry.

6.5 The use of a gas tube station protector is recommended. The station

ground should not exceed 50 ohms.

6.6 Plug the modular line cord from the faceplate assembly into the RJ11C

terminal block.

6.7 Dress the telephone line cord and AC cable away from the security screws

and seat the faceplate into the weatherproof housing.

6.8 Secure the cover assembly by tightening the security screws.

*****WARNING*****

A. Never install telephone wiring during a lightning storm.

B. The telephone must be grounded in accordance with local

and national electric codes.

C. Never install telephone jacks in wet locations unless the jack

is specifically designed for wet locations.

D. Never touch uninsulated telephone wires or terminals unless

the telephone line has been disconnected at the network

interface.

E. Use caution when installing or modifying telephone lines.

ISSUE 4.0

CEECO

Communication Equipment & Engineering Company

PROPRIETARY

6.9 OVER-VOLTAGE PROTECTION DIAGRAM

ISSUE 4.0

CEECO

Communication Equipment & Engineering Company

PROPRIETARY

7.0 TESTING

Action: Connect the telephone to a working telephone line.

Place a call to the telephone from another phone.

Reaction: The telephone rings. Press the "EMER/CALL" button to answer

the call. Provided the phone was programmed to allow incoming

calls, a normal speakerphone conversation should transpire.

Action: Finish the conversation.

Press the "EMER/CALL" button, or wait until

time out occurs.

Action: If the telephone has been mated with external call equipment, press

the "EMER/CALL" button to initiate a call.

Reaction: The external call equipment directs the call as intended and a

normal speakerphone conversation is allowed when the called

party answers.

Action: Finish the conversation.

Press the "EMER/CALL" button, or wait until

time out occurs.

Action: If the phone was programmed to not allow incoming calls, try

making a call to the phone.

Reaction: The telephone will ring, but it will drop the line when it is

answered and not allow a conversation to take place.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere CEECO Telefon Handbücher

CEECO

CEECO SSP-350-X Bedienungsanleitung

CEECO

CEECO SSC-303-D Bedienungsanleitung

CEECO

CEECO WPP-531-FD Bedienungsanleitung

CEECO

CEECO SSP-511-FD Bedienungsanleitung

CEECO

CEECO WPP-531-X-ADA-STROBE Bedienungsanleitung

CEECO

CEECO MHD-341-D Bedienungsanleitung

CEECO

CEECO SSC-501-F Bedienungsanleitung

CEECO

CEECO SSW-321-Xr1 Bedienungsanleitung

CEECO

CEECO WPP-531-DD Bedienungsanleitung

CEECO

CEECO SSP-350-X-145 Bedienungsanleitung

CEECO

CEECO IP-SSP-511- X Bedienungsanleitung

CEECO

CEECO SSP-511-F Bedienungsanleitung

CEECO

CEECO SSW-521-X-ADA Bedienungsanleitung

CEECO

CEECO SSW-321-F-IVC-C-M Bedienungsanleitung

CEECO

CEECO MHW-341-F-106 Bedienungsanleitung

CEECO

CEECO SSP-373-D Bedienungsanleitung

CEECO

CEECO BLW-321-F Bedienungsanleitung

CEECO

CEECO WPP-531-FD-ADA-AA-RP Bedienungsanleitung

CEECO

CEECO SSP-361-X Bedienungsanleitung

CEECO

CEECO SSP-363-D Bedienungsanleitung

CEECO

CEECO SSW-321-Dr1 Bedienungsanleitung

CEECO

CEECO SSW-323-F Bedienungsanleitung

CEECO

CEECO SSP-599-F Bedienungsanleitung

CEECO

CEECO WPP-331-F Bedienungsanleitung

Beliebte Telefon Handbücher anderer Marken

GE 2-9480 Bedienungsanleitung

Geemarc

Geemarc PHOTOPHONE 155 Bedienungsanleitung

D-Link

D-Link DWR-720/PW Bedienungsanleitung

Interquartz

Interquartz Gemini IQ333 Bedienungsanleitung

SSS Siedle

SSS Siedle HT 840-0 Bedienungsanleitung

Motorola

Motorola TITANIUM Bedienungsanleitung

Panasonic

Panasonic ICX Bedienungsanleitung

LG H870DS Bedienungsanleitung

Samsung

Samsung GT-I9500 Bedienungsanleitung

AT&T

AT&T Trimline 205 Bedienungsanleitung

Selta

Selta zenyth 600 Bedienungsanleitung

Doro

Doro AFTI 20 Bedienungsanleitung

UNIQCELL

UNIQCELL A1 Bedienungsanleitung

Panasonic

Panasonic KX Series Bedienungsanleitung

Jabra

Jabra SP5050 - Bluetooth hands-free Speakerphone Bedienungsanleitung

BT Decor 425 Bedienungsanleitung

NEC

NEC SV8500 Bedienungsanleitung

Teledex

Teledex PEARL Bedienungsanleitung