Celestron PowerSeeker 127EQ Technisches Datenblatt

Use the three tightening screws located at the

bottom of each leg to secure the extended legs

in place.

To set up the tripod, spread the legs outward

until they are fully extended. Extend the center

portion of each of the three tripod legs down 6-

8".

Item #31132

Quick Set-up Guide

123

All three legs should be the same length to

provide a level platform for the telescope.

Locate the equatorial mount and place the

base of the mount through the hole in the

center of the tripod mounting platform.

Properly assembled, the accessory tray should

appear as pictured above.

From underneath the tripod mounting platform,

thread the mounting bolt with washer into the

threaded hole on the bottom of the equatorial

mount.

Thread the latitude adjustment screw into the

equatorial mount until it is touching the inside

of the mount.

PowerSeeker 127

Your PowerSeeker 127 includes: optical tube w/

tube rings attached; tripod with center support

bracket; equatorial mount; two eyepieces; a 3x

barlow lens, finderscope; 5 lb. counterweight;

counterweight bar; two slow motion cables;

eyepiece accessory tray; The Sky™ CD software;

documentation including owner’s manual.

Item# 21049

Place the accessory tray on top of tripod's

center leg brace. Thread the tray into the

threaded hole in the center of the leg brace.

Questions or Problems with Set-up?

CONTACT:

Celestron Technical Support: 310.803.5955

For detailed usage information please

consult your owner’s manual.

Quick Set-up Guide [cont]

Locate the counterweight bar and

counterweight. Slide the counterweight half

way down the counterweight bar and tighten

the locking screw to secure in place.

Thread the threaded end of the counterweight

bar into the Dec axis of the equatorial mount.

The longer cable should attach to the Right

Ascension axis and the shorter cable attaches

to the Declination axis as shown above.

Before mounting the tube, remove the two

wingnuts on the tub rings.

Place the tube on the mount by lining up the

screws with the mounting holes on the mount.

Reattach both wingnuts and tighten to secure

in place.

17 18

Loosen the set screw on the focuser so that it

does not obstruct the inner diameter of the

focuser. Remove the plastic cap covering the

end of the focuser.

19 20

Locate the finderscope. Remove the knurled

nuts on the threaded posts at the focuser end

of the telescope tube.

Orient the finderscope so that the large lens is

facing towards the front of the tube. Place

finderscope over the posts on the tube and

tighten it down with the knurled nuts.

Remove the lens cap from the front of the

telescope. To observe, look through the

eyepiece as shown above.

For additional magnification, you can use the

included 3x barlow. Place the barlow in the

focuser in place of the eyepiece - remove the

cap from the barlow.

The focuser end of the telescope should be

over the counterweight assembly.

Slide the chrome end of the slow motion

control cables onto equatorial mount gear shaft

and tighten set screw to secure in place.

Insert the chrome barrel of the 20mm eyepiece

into the focuser and tighten the set screw.

Place the eyepiece into the barlow and tighten

the set screw to secure in place.

Andere Handbücher für PowerSeeker 127EQ

Dieses Handbuch passt für folgende Modelle

Andere Celestron Teleskop Handbücher

Celestron

Celestron 80AZS Bedienungsanleitung

Celestron

Celestron 60LCM Bedienungsanleitung

Celestron

Celestron 31034 Bedienungsanleitung

Celestron

Celestron Rowe-Ackermann 11 V2 F/2.2 Bedienungsanleitung

Celestron

Celestron Ultima 11 Bedienungsanleitung

Celestron

Celestron 31036 Bedienungsanleitung

Celestron

Celestron 12-36x50mm Bedienungsanleitung

Celestron

Celestron TRAVEL SCOPE 70 DX Bedienungsanleitung

Celestron

Celestron PowerSeeker 127 Bedienungsanleitung

Celestron

Celestron Ambassadorr 50AZ Bedienungsanleitung

Celestron

Celestron NexStar 8 Bedienungsanleitung

Celestron

Celestron 94223 Bedienungsanleitung

Celestron

Celestron NEXSTAR 60SLT Bedienungsanleitung

Celestron

Celestron CGE800 Bedienungsanleitung

Celestron

Celestron OmniXLT AZ Bedienungsanleitung

Celestron

Celestron FirstScope 114EQ Bedienungsanleitung

Celestron

Celestron Travel Scope 70 Bedienungsanleitung

Celestron

Celestron FirstScope 76 Bedienungsanleitung

Celestron

Celestron CGEM 1100 Bedienungsanleitung

Celestron

Celestron NexStar 80GTL Bedienungsanleitung

Celestron

Celestron LandScout Bedienungsanleitung

Celestron

Celestron 90AZ-SR Bedienungsanleitung

Celestron

Celestron PowerSeeker 50 Bedienungsanleitung

Celestron

Celestron C4.5 Bedienungsanleitung

Beliebte Teleskop Handbücher anderer Marken

Meade

Meade 81005 Condor Bedienungsanleitung

Meade

Meade 114 EQ-DS Bedienungsanleitung

Meade

Meade LX200 CLASSIC Bedienungsanleitung

Leica

Leica 82 HD Bedienungsanleitung

EASTCOLIGHT

EASTCOLIGHT 9920 Bedienungsanleitung

zoomion

zoomion Genesis 200 EQ Bedienungsanleitung

TEC

TEC APO 140 Bedienungsanleitung

Orion

Orion 7832 Bedienungsanleitung

Carson

Carson Skelescope SK-100 Bedienungsanleitung

SKY-WATCHER

SKY-WATCHER VIRTUOSO Bedienungsanleitung

Orion

Orion EZ Finder 7228 Bedienungsanleitung

cassini

cassini C-JRS Bedienungsanleitung

nedis

nedis SCTE5060WT Bedienungsanleitung

Meade

Meade Polaris 60EQ-D Bedienungsanleitung

PlaneWave

PlaneWave CDK700 Bedienungsanleitung

William Optics

William Optics Synta Crayford Bedienungsanleitung

Orion

Orion FUNSCOPE Bedienungsanleitung

Levenhuk

Levenhuk Skyline Travel Bedienungsanleitung