Celestron PowerSeeker 60 EQ Bedienungsanleitung

Item #31132

Quick Set-up Guide

123

All three legs should be the same length to

provide a level platform for the telescope.

Locate the equatorial mount and place the

base of the mount through the hole in the

center of the tripod mounting platform.

Properly assembled, the accessory tray should

appear as pictured above.

From underneath the tripod mounting platform,

thread the attached mounting bolt into the hole

on the bottom of the equatorial mount.

Thread the latitude adjustment screw into the

equatorial mount until it is touching the inside

of the mount.

PowerSeeker 60EQ

Item# 21043

Place the accessory tray on top of the tripod's

center leg brace. Thread the tray into the

threaded hole in the center of the leg brace.

Questions or Problems with Set-up?

CONTACT:

Celestron Technical Support: 310.803.5955

Use the three tightening screws located at the

bottom of each leg to secure the extended legs

in place.

To set up the tripod, spread the legs outward

until they are fully extended and push down

center leg brace. Extend the center portion of

each of the three tripod legs down 6-8".

Your PowerSeeker 60EQ includes: optical tube;

tripod with center leg brace; equatorial mount;

latitude adjustment screw; star diagonal; 2

eyepieces; a 3x barlow lens, 1.5x erect image

eyepiece; finderscope; 5 lb. counterweight;

counterweight bar; two slow motion cables;

eyepiece accessory tray; The Sky Level 1 software,

documentation including an owner’s manual.

Quick Set-up Guide [cont]

Locate the counterweight bar and

counterweight. Slide the counterweight half

way down the counterweight bar and tighten

the wingnut to secure in place.

Thread the threaded end of the counterweight

bar into the Dec axis of the equatorial mount.

The longer cable should attach to the Right

Ascension axis and the shorter cable attaches

to the Declination axis -- tighten set screw to

secure in place.

Before mounting the tube, remove the two

wingnuts on the tube.

Place the tube on the mount by lining up the

screws with the mounting holes on the mount.

Reattach both wingnuts and tighten to secure

in place. The front of the tube should be

positioned over the counterweight assembly.

17 18

Orient the finderscope so that the glass

window is facing towards the front of the tube.

Place finderscope over the holes on the tube

and replace the knurled nuts to secure.

19 20

Insert the chrome barrel of the 20mm eyepiece

into the star diagonal and tighten the set

screw.

Remove the lens cap from the front of the

telescope. To observe, look through the

eyepiece as shown above.

For additional magnification, you can use the

included 3x barlow. Place the barlow in the

focuser in place of the eyepiece - remove the

cap from the barlow.

Place the eyepiece into the barlow and tighten

the set screw to secure in place.

Locate the finderscope and remove plastic

caps on front and back of lens. Remove the

knurled nuts at the focuser end of the

telescope tube.

Slide the chrome end of the slow motion

control cable onto equatorial mount gear shaft

and tighten set screw to secure in place.

Loosen the set screw on the focuser so that it

does not obstruct the inner diameter of the

focuser. Insert the chrome barrel star diagonal

into the focuser and tighten the set screw.

For detailed usage

information please

consult your owner’s

manual.

Andere Celestron Teleskop Handbücher

Celestron

Celestron C10-N Montage- und Bedienungsanleitung

Celestron

Celestron Ambassadorr 50AZ Bedienungsanleitung

Celestron

Celestron C65 Bedienungsanleitung

Celestron

Celestron 31030 Bedienungsanleitung

Celestron

Celestron StarSense Explorer LT 127AZ Bedienungsanleitung

Celestron

Celestron PowerSeeker 21041 Bedienungsanleitung

Celestron

Celestron Travel Scope 60 Bedienungsanleitung

Celestron

Celestron AstroMaster 90 EQ Bedienungsanleitung

Celestron

Celestron Super C8 Bedienungsanleitung

Celestron

Celestron AstroMaster LT 60AZ Bedienungsanleitung

Celestron

Celestron 21035 Bedienungsanleitung

Celestron

Celestron Wide View 52260 Bedienungsanleitung

Celestron

Celestron PowerSeeker 60EQ 21043 Bedienungsanleitung

Celestron

Celestron Astro Fi 22205 Bedienungsanleitung

Celestron

Celestron National Park Foundation ExploraScope 60AZ Bedienungsanleitung

Celestron

Celestron StarSense Explorer DOBSONIAN Bedienungsanleitung

Celestron

Celestron G-9.25 Bedienungsanleitung

Celestron

Celestron Onyx80EDF Bedienungsanleitung

Celestron

Celestron ROWE-ACKERMANN F/2.2 SCHMIDT ASTROGRAPH 36... Bedienungsanleitung

Celestron

Celestron Ultima Series Bedienungsanleitung

Celestron

Celestron Comet Catcher Bedienungsanleitung

Celestron

Celestron StarSense Explorer LT Bedienungsanleitung

Celestron

Celestron Super C8 Bedienungsanleitung

Celestron

Celestron Ultima 52248 Bedienungsanleitung

Beliebte Teleskop Handbücher anderer Marken

Meade

Meade 81005 Condor Bedienungsanleitung

Meade

Meade 114 EQ-DS Bedienungsanleitung

Meade

Meade LX200 CLASSIC Bedienungsanleitung

Leica

Leica 82 HD Bedienungsanleitung

EASTCOLIGHT

EASTCOLIGHT 9920 Bedienungsanleitung

zoomion

zoomion Genesis 200 EQ Bedienungsanleitung

TEC

TEC APO 140 Bedienungsanleitung

Orion

Orion 7832 Bedienungsanleitung

Carson

Carson Skelescope SK-100 Bedienungsanleitung

SKY-WATCHER

SKY-WATCHER VIRTUOSO Bedienungsanleitung

Orion

Orion EZ Finder 7228 Bedienungsanleitung

cassini

cassini C-JRS Bedienungsanleitung

nedis

nedis SCTE5060WT Bedienungsanleitung

Meade

Meade Polaris 60EQ-D Bedienungsanleitung

PlaneWave

PlaneWave CDK700 Bedienungsanleitung

William Optics

William Optics Synta Crayford Bedienungsanleitung

Orion

Orion FUNSCOPE Bedienungsanleitung

Levenhuk

Levenhuk Skyline Travel Bedienungsanleitung