Celexon PL2000 Bedienungsanleitung

celexon.

www.celexon.com

EC declaration of conformity

Manufacturer: celexon Germany GmbH & Co. KG

Address: Gutenbergstraße 2, 48282 Emsdetten, DE

Hereby declares that the following product

Product name: celexon projector lift PL2000

Part number: PL2000

Manufacturer: celexon Germany GmbH & Co. KG,

48282 Emsdetten, DE

Complies with the following standards:

CE EN 50081-1, CE EN 50082-1

Notes:

The tests were carried out in normal mode and refer to the tested

device under the specied tests. This certicate applies only to the

devices tested.

Emsdetten, 10.07.2017

Christoph Hertz

Managing Director

celexon.

Installation Manual

celexon projector lift PL2000

Thank you for purchasing this product. Before installing the projector lift,

please read the following instructions carefully.

Safety instructions

Disclaimer

Cleaning instructions

Do not start installation before reading the complete installation manual and the

safety warnings.

This product should only be installed by qualied personnel (with mechanical and

electrical experience).

Please ensure that the ceiling can carry the complete weight of ceiling lift and

mounted hardware.

If necessary, carry out the installation with another person to ensure safe

installation.

Tighten the screws but ensure that they are not overtightened as this would reduce

the load bearing capacity.

This product is designed for indoor use only. Outdoor use could result in damage

to the product and may cause injury.

Hanging loads must be tested at least twice a year for strength and carrying

capacity.

Do not stand under the ceiling lift during operation.

Do not dismantle the lift into its piece parts.

Do not lean heavy loads against the projector or lift.

The information in this document is subject to change without prior notice.

Changes will be documented in future editions of this manual. The manufacturer

does not guarantee accuracy of the information contained in this document.

Clean the product only with a soft and clean cloth. If necessary, use a mild soapy

solution to remove any dirt.

Symbols

Product label

This ceiling lift is clearly identied by a product identication label that contains its

key technical information.

A Product type

B Product name

C Serial number

D Year of manufacture

E Operating voltage

F Power frequency

G Phases

H Power consumption

Important:

This symbol is used to indicate recommendations, guidelines and

information that are important when using the product.

Danger:

This symbol is used to indicate safety instructions in this manual

which must be strictly adhered to in order to ensure safe handling

of this product. Failure to do so may result in serious injury or

death.

Warning:

This symbol is used to indicate safety warnings in this manual

which could lead to injury or damage to the product if not

observed.

celexon Germany GmbH & Co. KG

Gutenbergstraße 2

48282 Emsdetten

Deutschland

www.celexon.com

warning 1

Position of product label

product label

Warnings

Warning 1 is important and must be followed:

It is possible to be harmed by the scissor joint if you are positioned too close. Please

ensure that there is sucient distance when using the lift and that people, cables or

other objects are kept a safe distance from the mechanism.

warning 2

position of

warning 1

position of

warning 2

Warnings

Warning 2 refers to the maximum load capacity of the lift which is the total of the

weight of the projector, the lift itself and the ceiling tile that is attached to the lift.

The actual weight must never exceed the maximum load specied.

Important advice for the installation and use

Important advice for the installation and use of the ceiling lift:

The celexon ceiling lift PL2000 is a motorised lift for projectors. The

lift should only be installed indoors, protected from environmental

factors such as humidity, cold or heat.

This product should only be installed by qualied personnel (with mechanical and

electrical experience). After installation, only the owner or authorised personnel

should use the ceiling lift. Please avoid misuse by third parties.

Before using the lift, you should be adequately instructed in its functions, as well as

of any possible risks when using the lift. Operation should be strictly in accordance

with the instructions in this manual.

It is strictly forbidden to use the lift contrary to these instructions or for a purpose

that it was not intended for.

The above instructions must be observed by installers, technicians and all users.

Important advice for the installation and use

Safety instructions and possible risks

The lift is designed for professional use only. Failure to comply with these

instructions may result in damage to the lift itself or to the video projector located

therein and/or may create dangerous situations for which the manufacturer is not

responsible or liable.

It is strictly forbidden to:

Connect the lift to a dierent AC voltage than specied on the

product label

Use the lift to move animals or objects other than a projector

Exceed the maximum load specied

Install and use the lift outdoors

The lift should only be used for the purposes intended. The

manufacturer does not accept liability for injury to people, animals

or damage to objects due to improper or negligent use.

MAKE SURE THAT THE LIFT IS DISCONNECTED FROM THE MAINS

BEFORE STARTING INSTALLATION, CLEANING OR MAINTENANCE

WORK.

Do not remove any warnings or stickers attached to the lift.

Do not activate the lift if it is not fully assembled and / or safety device is

dismantled or safety warnings are missing.

It is possible to stop the lift at any time by using the up / down switch if

necessary.

In the case of a defect or malfunction, please do not attempt any repairs on the

lift, but contact your dealer or manufacturer.

To connect the lift with the power cable you must follow the instructions in this

manual (see section Electric connections).

Warning: Once the lower stop

position point has been set, x

both safety screws tightly with an

allen key at a distance of 10mm

from the scissor joint.

10 mm

Description of safety devices

The lift is equipped with two safety screws which are located on the bottom left

prole and the bottom right prole (see illustration below).

The screws can be positioned freely and will prevent the lift from dropping in the

event of a defective rope.

Minimum height including ceiling tile H = 2.75m

Minimum height excluding ceiling tile H = 2.50m

CEILING

L=1,00 ml L=1,00 ml

FLOOR

Residual risks (rs)

Please ensure that no people, animals or objects are underneath the lift or near the

area that the lift needs to move in and out when the lift is in use.

The drawing below identies the residual risk area which should be avoided when

using the lift and during installation of the projector.

Inhaltsverzeichnis

Andere Celexon Scherenhebebühne Handbücher

Celexon

Celexon PL1000 Plus Bedienungsanleitung

Beliebte Scherenhebebühne Handbücher anderer Marken

SolidHub

SolidHub SBE900 Bedienungsanleitung

Still

Still HPT 10 XE Bedienungsanleitung

Plafolift

Plafolift PHD 26 Bedienungsanleitung

Mec

Mec 4069RT Bauanleitung

JLG

JLG ES2632 Gebrauchs- und Pflegehandbuch

Happ

Happ Happ10 Bedienungsanleitung

Snorkel

Snorkel S3219E Bedienungsanleitung

Kleton

Kleton MJ523 Bedienungsanleitung

Mec

Mec SE Series Bauanleitung

ATT

ATT Nussbaum UNI LIFT 6500 Bedienerhandbuch

Skyjack

Skyjack SJ 6826RT Bedienungsanleitung

ATH

ATH Frame Lift 30FZ Bedienungsanleitung

Haulotte

Haulotte H12SX Produkthandbuch

GMG

GMG 3394-RT Bedienungsanleitung

Upright

Upright X26 Ultra Narrow Bedienungsanleitung

Skyjack

Skyjack SJIII Series Bedienungsanleitung

Haulotte Group

Haulotte Group Compact 10DX Bedienungsanleitung

Launch

Launch TLT830WA Bedienungsanleitung