Cell2 SW833 Bedienungsanleitung
SW833
Installation & Operation Manual
Control Panel 8+2 Outputs - 3 Inputs
Table of Contents
Warning & Precautions
Warning & Precautions ....................................................................................... 2
Chapter 1: Contents & Specifications
1-1 Contents ....................................................................................................... 3
1-2 Specifications ............................................................................................... 3
Chapter 2: Installation
2-1 Mounting ...................................................................................................... 4
2-1-1 Screw Mount Bracket ......................................................................... 4
2-1-2 Suction Cup Mount ............................................................................ 4
2-1-3 Power Module .................................................................................... 5
2-1-4 Placement of Decals .......................................................................... 5
2-2 Wiring .......................................................................................................... 6
2-2-1 Power Module .................................................................................... 6
Chapter 3: Programming & Operation
3-1 General Operation for Programming Mode .................................................. 7
3-2 Standby Mode .............................................................................................. 9
3-3 Default Configuration of Buttons .................................................................... 9
3-4 Scene 1 and Scene 2 Controlled by B5 and B6 ............................................ 11
3-5 Programming Mode 1 .................................................................................. 12
3-6 Programming Mode 2 .................................................................................. 19
3-7 Button Combo: Group 1 ............................................................................... 23
3-8 Button Combo: Group 2 ............................................................................... 23
3-9 Button Combo: Group 3 ............................................................................... 23
- 1 -
- 2 -
Warning & Precautions
Before installation and operation – read all instructions,
warnings and precautions thoroughly and carefully.
Deliver this manual to the end user of this product.
NOTICE TO INSTALLER
1. Failure to follow these instructions could result in serious damage to the unit or vehicle and
may void warranties.
2. Proper installation of the product requires the installer to have a good understanding of
automotive electronics, systems and procedures. It is essential to install the unit properly
to ensure safe and reliable operation.
3. Do not install this product or route any wires in the air bag deployment zone of your vehicle.
Equipment mounted or located in air bag deployment zones will damage or reduce the
effectiveness of the air bag, or become a projectile that could cause serious personal
injury or death. Refer to your vehicle owner’s manual to learn the air bag deployment
zones for the vehicle.
4. A properly-rated fuse must be installed as close to the battery as possible to protect the wires.
5. The same applies to any devices controlled by the installed device.
6. Ensure that none of the vehicle's original controls will be affected by the installed device.
7. Ensure that any unit is located in an area that allows both the vehicle and the control panel
to be operated safely in any driving condition.
- 3 -
1-1. Contents
Chapter 1: Contents & Specs
Power Module x 1 pc
Controller x 1 pc
RJ45 Cable (4m) x 1 pc
Terminal Block x 1 pc
Self-drilling Screw x 4 pcs
(#8 x 1″)
6-Pin Wire Harness x 1 pc
Adjustable Bracket
(based on the model ordered)
Suction Cup Bracket x 1 pc
Suction Base x 1 pc
Screw Mount Bracket x 1 pc
Self-drilling Screw x 2 pcs
(Ø4 x 15mm)
Decals x 1 set
Manual x 1 pc
1-2. Specifications
1-2-1. Controller
Operating Voltage: 10~30VDC
Operating Temperature: -40°C~60°C
Dimensions: 68.8mm x 95mm x 25.5mm
1-2-2. Power Module
Number of Positive Outputs: 8
Number of Negative Outputs: 2
Max Current / Positive Outputs: 1x 15A, 2x 10A, 1x 10A (for Output 4~8)
Max Current / Negative Outputs: 2x 2A
Fuse Rating: 50A (user-supplied)
Dimensions: 100.5mm x 91.6mm x 25mm
Adjustable Bracket
Screw MountSuction Cup
A1
A2
B1
B2
A2
A1 B1
B2
- 4 -
2-1. Mounting
2-1-1. Screw Mount Bracket
2-1-2. Suction Cup Bracket
1. Choose a desired place for installation.
2. Use the base as the template to locate and mark two mounting holes on the mounting
surface.
3. Secure the bracket with the two Ø4 self-drilling screws supplied.
4. Assemble the controller with the bracket by tightening the knurled knob in a firm way.
5. Adjust the bracket at an angle most convenient to your operation.
1. Choose a desired place for installation.
2. Press the suction cup to install the controller on the windshield directly. Or assemble
the adhesive base at the bottom of the suction cup and follow the instructions below.
3. Mount the suction cup onto the mounting surface and allow the adhesive to set for at
least 24 hours.
4. Assemble the controller on the bracket by tightening the knurled knob in a firm way.
5. Adjust the bracket at an angle most convenient to your operation.
Chapter 2: Installationa
1.97" (50mm)
2.72" (69.2mm)
2-R4.5
1.97" (50mm)
- 5 -
2-1-3. Power Module
2-1-4. Placement of Decals
1. Choose a flat surface to install the power module.
2. Use the power module as the template to locate and mark four mounting holes on the
mounting surface.
3. Secure the power module with the four #8 self-drilling screws supplied.
NOTE: Always install the power module away from a heat source.
1. The controller is shipped without any button decals installed.
2. After assembling the controller and the mounting bracket, apply a desired decal above
each button to facilitate subsequent programming and operation.
3.21" (81.58mm)
1.64" (41.54mm)
2.07" (52.54mm)
8-R2.50
3.95" (100.33mm)
3.61" (91.63mm)
- 6 -
2-2. Wiring
2-2-1. Power Module
No function
WHITE – Input 3 (+)
YELLOW – Input 1 (+)
BLUE – Negative Output 1 (max. 2A)
ORANGE – Input 2 (-)
BROWN – Negative Output 2 (max. 2A)
Blade Terminals
Positive Output 1 (max. 15A)
Positive Output 2 (max. 10A)
Positive Output 3 (max. 10A)
Positive Output 4
Positive Output 5
Positive Output 6
Positive Output 7
Positvie Output 8
Power Indicator
RJ45 Cable
Terminal Block
6-Pin Wire Harness
Blade Terminals (user-supplied)
Power
Indicator
RJ45
Cable Terminal
Block
6-Pin Wire
Harness
ABCDEFGH
A
B
C
D
E
F
G
H
Total current of Output 4~8 is 10A max.
- 7 -
3-1. General Operation for Programming Mode
Programming Mode 1 and Programming Mode 2
SW833 Controller has two programming modes.
Programming Mode 1 allows you to configure B1~B8 and the settings of each input.
Programming Mode 2 allows you to configure the Traffic Arrow function, input configuration
of Traffic Arrow, Standby Mode, B4 flashing mode under Standby Mode and Buzzer ON/OFF
configuration.
You can also reset to factory default configuration in Programming Mode 2.
Enter a Programming Mode
Press B1 and B3 for more than 1 second to enter Programming Mode 1.
Press B2 and B4 for more than 1 second to enter Programming Mode 2.
NOTE: The indicator light in the upper right corner will flash in single flash for Mode 1, or
double flash for Mode 2.
Change Setting Value
1. Press B1 and B3 for more than 1 second to enter Programming Mode 1.
2. Press the button you would like to configure. The indicator light at the upper left corner will
be lit up to indicate the current setting (1 light = Setting #1, 2 lights = Setting #2… and so
on).
3. Press the button again to go to the next setting. The indicator light will show the current
setting according the rule mentioned above.
4. Press B1 and B3 for more than 1 second to exit and save your configuration.
Chapter 3: Programming & Operation
Mode 1: Single flash Mode 2: Double flash
B1 B2 B3 B4
B5 B6 B7 B8
B1 B2 B3 B4
B5 B6 B7 B8
- 8 -
Error Signal
Under Programming Mode 1 or Mode 2, when you program a button with the function cannot
be activated (e.g. B1 has been set as a permanent switch. Configure B3 to activate B1
automatically), an error occurs and the green backlight will flash three times on those buttons
with three “beep” sounds.
Reset to Factory Default Configuration
1. Press B2 and B4 for more than 1 second to enter Programming Mode 2.
2. Press and hold B3 and B4 for more than 5 seconds.
3. If SW833 Controller has been restored to factory default configuration successfully, the
controller will return to operation mode (after “beep” for three times and green backlight is
ON).
Automatic Standby Mode (default configuration)
Automatically enter Standby Mode after 15 minutes if no buttons are activated and Input 1 is
not activated either.
(Refer to 3-6 Programming Mode 2, p.19, for detailed information of Standby Mode Configu-
ration)
NOTE: After entering Standby Mode, Programming Mode CANNOT be accessed by default.
If you want to enter Programming Mode, disconnect all power and reboot your SW833
Controller.
Testing Mode (for factory users only)
1. Enter Programming Mode 2.
2. Press and hold B7 and B8 for more than 3 seconds.
3. Under Testing Mode, you can test the connection of Input 1 / Input 2 / Input 3 respectively.
4. After finishing testing, disconnect all power to exit Testing Mode.
NOTE: Testing Mode is accessible ONLY under Factory Default Configuration.
- 9 -
3-3. Default Configuration of Buttons
B1 = POSITIVE OUTPUT 1
ON/OFF switch
Activate B1 will activate the main warning light.
When B1 (main warning light) is interlocked by B2 (siren), it is possible to activate B1 by
pressing B2.
Also Input 3 can be connected to an external switch to activate B1 (main warning light) and
B2 (siren).
B1 B2 B3 B4
B5 B6 B7 B8
Enter Standby Mode Manually (default configuration)
Manually enter Standby Mode by pressing B4 for more than 1 second.
It will turn off all button functions.
(Refer to 3-6 Programming Mode 2, p.19, for detailed information of Standby Mode Configu-
ration)
NOTE: After entering Standby Mode, Programming Mode CANNOT be accessed by default.
If you want to enter Programming Mode, disconnect all power and reboot your SW833
Controller.
B1 B2 B3 B4
B5 B6 B7 B8
Standby
By default, red backlight will
flash to indicate under Stand-
by Mode.
3-2. Standby Mode
Enter Standby Mode Automatically (default configuration)
Automatically enter Standby Mode after 15 minutes if no buttons are activated and Input 1 is
not activated either.
Inhaltsverzeichnis
