Cembre B-TC950A Bedienungsanleitung

OPERATION AND MAINTENANCE MANUAL

17 M 217 U

BATTERY OPERATED HYDRAULIC

CUTTING TOOL

ENGLISH

B-TC950A B-TC950NA

FIG. 1b

Steel

Low battery

FIG. 3

FIG. 3a FIG. 4

FIG. 2

Cu Al

Ø MAX. 95 mm

(3-3/4”)

FIG. 1a

Makita Battery

Metabo Battery

LOCKING LEVER

UPPER BLADE

LOWER BLADE

RING FOR SHOULDER STRAP

HANDLE GRIP

LED WORKLIGHT

OPERATING BUTTON

PRESSURE RELEASE BUTTON

BATTERY RELEASE

BATTERY ADAPTER

BATTERY

FIG. 5

B-TC950A B-TC950NA

– Before using the tool, carefully read the instructions in this manual.

– Keep hands clear of cutting blades.

– Always wear safety glasses and gloves when operating this tool.

WARNING SYMBOLS

– User information applies in member states of the European Union

(Directives 2011/65/EU and 2012/19/EU), see page 10.

Battery

Tool

(

– Do not cut Steel.

– Never throw batteries into re or water.

– Always recycle the batteries.

– Do not discard batteries into domestic refuse or waste disposal.

1. GENERAL CHARACTERISTICS

(1) Directive 2006/42/EC, annexe 1, point 1.7.4.2 letter u

LpA

= weighted continuous acoustic pressure level equivalent.

LpCPeak

= maximum value of the weighted acoustic displacement pressure at the work place.

LWA

= acoustic power level emitted by the machine.

(2) Directive 2006/42/EC, annexe 1, point 2.2.1.1

Weighted root mean square in frequency of the acceleration the upper limbs are exposed to for each biodynamic

reference axis. Tests carried out in compliance with the indications contained in EN ISO 5349-1/2 Standard and under

operating conditions much more severe than those normally found.

B-TC950A B-TC950NA

Application range suitable for cutting Copper, Aluminium

or telephone cables

Max. cutting diameter

mm (inches) 95 (3-3/4)

Operating pressure

bar (psi) 880 (12,700)

Dimensions mm (inches) 518 x 468 x 83

(20.4 x 18.4 x 3.3)

518 x 488 x 83

(20.4 x 19.2 x 3.3)

Weight with battery kg (lbs) 7,8 (17.1) 7,9 (17.4)

Motor V DC 18

Operating temperature °C (°F) -15 to +50 (+5 to +122)

Recommended oil ENI ARNICA ISO 32 or equivalents

Operating speed twin speed operation and automatic switching from

a rapid advancing speed of the ram to a slower, more

powerful speed

Safety maximum pressure valve

Rechargeable battery type CB1840L MAKITA BL1850B

Type V / Ah (Wh) 18 / 4.0 / (72) 18 / 5.0 (90)

Weight kg (lbs) 0,66 (1.45) 0,6 (1.3)

Acoustic noise

(1)

dB (A)

pCPeak

dB (C) 94.5

dB (A) 79

Vibration

(2)

m/s

0.575 max.

Battery charger

Input

type

V / Hz

ASC30-36 MAKITA DC18RC

115 / 60 120 / 50 - 60

This tool has been specically designed for cutting Copper or Aluminium cables.

DO NOT ATTEMPT TO CUT STEEL ROPES OR STEEL REINFORCED CONDUCTORS.

Do not use the tool for purposes other than those intended by Cembre.

The operator should concentrate on the work being performed and be careful to maintain a

balanced working position.

Work in a clean, uncluttered area. Keep persons away from immediate work area.

Inspect the blades before each use. Do not use damaged blades.

Damaged blades can break and cause injury or damage to the tool.

Before each use, verify the integrity of the tool; replace any worn, possibly damaged or missing

parts with original Cembre spares.

Wear eye protection. Metal chips can y from blades when cutting.

Do not cut live cables or conductors.

The tool is unsuitable for continuous use and should be allowed to cool down following uninter-

rupted, successive cutting operations; for instance, having exhausted a fully charged battery in

one session, delay battery replacement for a few minutes.

Protectthetoolfromrainandmoisture.Waterwilldamagethetoolandbattery.Electro-hydraulic

tools should not be operated in pouring rain.

The part reference includes the following:

Hydraulic cutting tool (B-TC950NA is tted with adapter to use Makita battery).

Li-Ion rechargeable battery (2 pcs) (model depends on the tool version).

Battery charger.

Shoulder strap.

Plastic carrying case.

USB cable (Ref. to § 5).

2. INSTRUCTIONS FOR USE

The tool can be easily carried using either the handle or the shoulder strap attached to ring (4)

(Ref. to Fig. 5).

Before starting any work, check the battery charge (Ref. to § 2.7) and recharge if necessary.

Refer to the manufacturer's instructions for the correct use of battery and battery charger.

WARNING

To replace the battery, remove it by pressing the release button (9) (Ref. to Fig. 1a and 1b),

B-TC950A: in the g. 1a press the release button (9) and slide the battery out unlocking it.

B-TC950NA: in the g. 1b press the release buttons (9) and slide the battery out unlocking it.

Insert a charged battery by sliding it into the guides until it locks.

2.1) Head rotation

For ease of operation, the tool head can rotate through 335°, allowing the operator to work in the

most comfortable position (Ref. to Fig. 3).

Do not attempt to rotate the head when the hydraulic circuit is pressurised.

2.2) Setting

Insert the conductor between the blades, up to the desired cutting point (Ref. to Fig. 3).

For a running conductor, press the locking lever (1) and open the tool head (Ref. to Fig. 3a).

Fully retract the lower blade (3) before attempting to open the tool head (Ref. to § 2.6).

With the conductor on the lower blade (3), close the tool head and fully secure the lever (1).

Before commencing the cutting operation ensure that the lever (1) is fully secured: partial

closure may damage the tool head.

2.3) Blade advancement

Press the operating button (7) (Ref. to Fig. 3) to activate the motor-pump, the ram will gradually

move forward until the lower blade (3) touches the conductor.

To halt the advancement, release the button (7) and the motor will cut out.

2.4) Cutting

Firmly hold the tool and operate the button (7) to gradually move the lower blade (3) to cut

through the conductor.

When the cut is performed, release the button (7), otherwise after the maximum pressure relief

valve has activated the motor will stop automatically.

2.5) LED Worklights

Whilst the tool is in operation, the work area is illuminated by two high luminosity LED Worklights

that switch o automatically at the end of the cycle.

2.6) Blade retraction

By operating the pressure release button (8), the ram will retract and open the lower blade.

2.7) Using the battery charger

Carefully follow the instructions in the battery charger user manual.

2.8) Battery status (Metabo battery)

ThebatteryisequippedwithLEDindicatorsthatindicatetheremain-

ing battery life at any time by pressing the adjacent button (12):

4 LEDs illuminated: fully charged

2 LEDs illuminated: 50 % capacity

1 LED flashing: minimum charge, replace the battery.

Workligths(6) illuminated combined with an alarm audible

when the operating button (7) is pressed (Ref. to Fig. 5), indicate that the battery voltage has

dropped below a minimum safety threshold; under these conditions the tool will not start,

and it is necessary to recharge or replace the battery. The approximate time to fully recharge a

battery is about 80 minutes.

After each working cycle, and after the extraction of the battery from the tool, an integrated

battery cut-o device will operate after 70 s approx. Then the LED nearest to button (12) will

ash 5 times each 14 s approx. The battery will be reactivated when it is reintroduced into

the tool and the operating button is pressed.

3. MAINTENANCE

The tool is robust, completely sealed, and requires very little daily maintenance. Compliance with

the following points, should help to maintain its optimum performance:

3.1) Thorough cleaning

Dust, sand and dirt are a danger for any hydraulic device. Every day, after use, the tool must be

wiped with a clean cloth taking care to remove any residue, especially close to pivots and move-

able parts.

Do not use hydrocarbons to clean the rubber parts.

Regularly lubricate the moving parts and pivot pins of the head with a few drops of oil.

3.2) Storage case

When not in use, the tool should be stored and transported in the metal case, to prevent damage.

Metal case: VAL-B-TC950, size 565x410x132 mm (22.2x16.1x5.2 in.), weight 6,7 kg (14.7 lbs).

3.3) Routine maintenance

When the tool reaches the predetermined number of hours worked, it will signal that routine main-

tenance is recommended.

The tool will continue to work however 15 sec. after use an alarm comprising 3 beeps com-

bined with illumination of the worklights will signal that its return to Cembre for service is

recommended (see § 6).

4. BLADE REPLACEMENT (Ref. to g. 6)

When changing blades, the battery must rst be removed from the tool.

After extended use, the blades may lose their cutting edge. Replace the blades as follows:

FIG. 6

100

101

103102

Lower blade

– Press lever (1) and open upper blade assembly.

– Operate tool to advance the lower blade (3) until holding screw (18) is visible on the ram (13),

than remove the battery from the tool.

– Using a at blade screwdriver remove the holding screw (18) and release the lower blade (3).

– Insert the new blade and t the holding screw.

Before closing the tool head, release the oil pressure and retract the lower blade, otherwise

the tool head assembly may hit and damage the lower blade.

Upper blade

– Press lever (1) and open upper blade assembly.

– Remove circlip (38) and pin (37).

– With a 13 mm spanner, undo M8 nuts (98) and remove two studs (99), blade guide (100) blade

spacer (101) and upper blade (2), noting the order of assembly.

– With a punch, drive out the split pin (102), collecting the spring (103) and the pin (97).

– Assemble the spring (103) and the pin (97) on the new blade, locking the whole by the split pin

(102).

– Fitting the new blade is a reversal of the above.

5. CONNECTION TO COMPUTER

Thememorycardintegratedinthetoolrecordsoperatingdata fortransferviathe USBcablesupplied.

To view and manage this data, go to www.cembre.com and register in the dedicated area, then

download the free Cembre software CEM_SWBT01.

Keeping the Firmware of the tool updated, via free of charge download from here, will optimise

the tool’s performance.

CBA-MTMK

Screw FIG. 7

B-TC950NA: To access the mini-USB

port (Ref. to g. 8) and connect the USB

cable to the computer it is necessary

to remove CBA-MTMK battery adapter.

Remove the screws (Ref. to g. 7 and 7a)

and slide the adapter out.

mini-USB

FIG. 7a

FIG. 8

B-TC950NA

USER INFORMATION in accordance with “Directives 2011/65/EU and 2012/19/EU.“

The‘Notinthebin’symbolabovewhenshownonequipmentorpackagingmeansthat

the equipment must, at the end of its life, be disposed of separately from other waste.

The separate waste collection of such equipment is organised and managed by the manufacturer.

Users wishing to dispose of such equipment must contact the manufacturer and follow the prescri-

bed guidelines for its separate collection. Appropriate waste separation, collection, environmentally

compatible treatment and disposal is intended to reduce harmful environmental eects and pro-

mote the reuse and recycling of materials contained in the equipment. Unlawful disposal of such

equipment will be subject to the application of administrative sanctions provided by current legi-

slation.

–

Following information applies in member states of the European Union:

Andere Handbücher für B-TC950A

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Cembre Cutter Handbücher

Cembre

Cembre B-TC500YA Bedienungsanleitung

Cembre

Cembre HT-TC065 Bedienungsanleitung

Cembre

Cembre TC050Y-KV Bedienungsanleitung

Cembre

Cembre B-TC650-SC Bedienungsanleitung

Cembre

Cembre B500-TFC Bedienungsanleitung

Cembre

Cembre B-TC320ND Bedienungsanleitung

Cembre

Cembre B-TC250BS Bedienungsanleitung

Cembre

Cembre B35M-TC025 Bedienungsanleitung

Cembre

Cembre B-TC04 Bedienungsanleitung

Cembre

Cembre B-TC650NA Bedienungsanleitung

Cembre

Cembre TC050 Bedienungsanleitung

Cembre

Cembre B-TC04 Bedienungsanleitung

Cembre

Cembre HT-TC026Y Bedienungsanleitung

Cembre

Cembre B-TC550NA Bedienungsanleitung

Cembre

Cembre HT-TC051 Bedienungsanleitung

Cembre

Cembre B35M-TFC Bedienungsanleitung

Cembre

Cembre B-TC450 Bedienungsanleitung

Cembre

Cembre HT-TC065 Bedienungsanleitung

Cembre

Cembre TC050Y Bedienungsanleitung

Cembre

Cembre B-TC250YA Bedienungsanleitung

Cembre

Cembre B35 Bedienungsanleitung

Cembre

Cembre HT-TC051Y Bedienungsanleitung

Cembre

Cembre B-TC065-SC Bedienungsanleitung

Cembre

Cembre HT-TC026 Bedienungsanleitung

Beliebte Cutter Handbücher anderer Marken

Milwaukee

Milwaukee HEAVY DUTY M12 FCOT Bedienungsanleitung

Makita

Makita DCS552 Bedienungsanleitung

SignWarehouse.com

SignWarehouse.com Bobcat BA-60 Bedienungsanleitung

Makita

Makita 4112HS Bedienungsanleitung

GEISMAR STUMEC

GEISMAR STUMEC MTZ 350S Bedienungsanleitung

Hitachi

Hitachi CM 4SB2 Fehlerbehebungshandbuch

Dexter Laundry

Dexter Laundry 800ETC1-20030.1 Bedienungsanleitung

GCC Technologies

GCC Technologies AFJ-24S Bedienungsanleitung

DeWalt

DeWalt XR LI-ION DCS350N Bedienungsanleitung

Baudat

Baudat ES1 Bedienungsanleitung

Mafell

Mafell ZAF 200 Leitfaden

Makita

Makita 4100NH Bedienungsanleitung

Formax

Formax FD 574 Bedienungsanleitung

EINHELL

EINHELL TE-MA 1500 Bedienungsanleitung

Husqvarna

Husqvarna Cut-n-Break K 760 Bedienungsanleitung

CLEAN ROOM DEVICES

CLEAN ROOM DEVICES CRD130SS Bedienungsanleitung

TRI tool

TRI tool 301A Bedienungsanleitung

Roller

Roller King 1 1/4 Bedienungsanleitung