Central Machinery 61700 Montageanleitung

Page 2 For technical questions, please call 1-888-866-5797. Item 61700

Specifications (per Sawhorse)

Wood Top Dimensions 32" x 5-1/2" x 1-1/2"

Height 30"

Maximum Weight Capacity 1000 lb for each Sawhorse

(must be used in pairs)

IMPORTANT SAFETY INFORMATION

Assembly Precautions

1. Assemble only according to these instructions.

Improper assembly can create hazards.

2. Wear ANSI-approved safety goggles and

heavy-duty work gloves during assembly.

3. Keep assembly area clean and well lit.

4. Keep bystanders out of the area during assembly.

5. Do not assemble when tired or when under the

influence of alcohol, drugs or medication.

6. Weight capacity and other product capabilities apply

to properly and completely assembled product only.

Use Precautions

1. This product is not a toy. Do not allow

children to play with or near this item.

2. Use on flat, level, hard surface able to support load.

3. Wear ANSI-approved safety goggles

during assembly and use.

4. Use as intended only. Use at least

two sawhorses to support load.

5. Inspect before every use; do not use

if parts loose or damaged.

6. Secure the workpiece to the sawhorses, if possible.

7. Do not exceed listed weight capacity 1,000 lb weight

capacity, evenly distributed across two sawhorses.

Be aware of dynamic loading!

Sudden load movement may briefly create

excess load causing product failure.

8. Maintain product labels and nameplates.

These carry important safety information.

If unreadable or missing, contact

Harbor Freight Tools for a replacement.

9. The warnings, cautions, and instructions discussed

in this instruction manual cannot cover all possible

conditions and situations that may occur. It must

be understood by the operator that common sense

and caution are factors which cannot be built into

this product, but must be supplied by the operator.

Page 3For technical questions, please call 1-888-866-5797.Item 61700

Assembly Instructions

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document

including all text under subheadings therein before set up or use of this product.

1. On the Wooden Board (1), measure 3-3/8" from each

end of the Wooden Board. Mark a line with a pencil.

2. Line up the wide end of the Leg Mounting

Bracket (2) with the line. There are four holes in

the primary plate of the Leg Mounting Bracket.

Use four Screws (8) to attach the Bracket to the

Wooden Board through those holes. Repeat

on the opposite end of the Wooden Board.

3. Place the end of a leg into one side of the Leg

Mounting Bracket, lined up with the mounting

holes in the walls of the Bracket. The open side

of the leg should face inward. See Figure A.

Wooden Board (1) Mounting

Bracket (2)

Nut (10)

Leg (3)

Bolt (9)

Figure A

4. Secure the Leg to the Bracket with Bolt (9)

and Nut (10). Tighten enough to allow limited

movement. Repeat with the remaining Legs.

5. Place a Foot (5) on the end of each Leg (3). Note

the angle of the Foot: the longer edge of the Foot

should be on the outer side of the Leg. See Figure B.

Foot (5)

outer

side of

Leg (3)

Figure B

6. Attach the Brace (4) between two of the Legs

on one side of the Sawhorse. See Figure C.

Nut (15)

Leg (3)

Carriage

Bolt (14)

Brace (4)

Figure C

a. Press the flat side of the Brace

against the outside of the Legs.

b. Secure with four Carriage Bolts (14) and Nuts (15).

c. Leave all hardware in this step

slightly loose for now.

d. Repeat on the opposite side.

7. Attach the closed end of the Leg Locking Brace (6)

between two of the Legs on one end of the

Sawhorse, using a Bolt (9), Washer (12), and Nylon

Insert Nut (11). Ensure that the hook opening of

the Leg Locking Brace faces toward the ground.

(See Figure F). Tighten the Bolt and Nut enough

to allow movement. See Figure D and Figure E.

Leg (3)

Bolt (9)

Leg Locking

Brace (6)

Figure D

Leg Locking Brace (6)

Nylon Insert

Nut (10)

Figure E

Page 4 For technical questions, please call 1-888-866-5797. Item 61700

8. Install a Bolt on the opposite Leg.

a. Insert a Bolt through the mounting

holes from the inside of the Leg.

b. Add a Split Lock Washer (13) and Nut to the

outer side of the Leg, leaving the Bolt exposed.

c. Tighten securely.

d. Hook the open end of the Leg Locking

Brace over the exposed Bolt.

e. Twist the Locking Knob (7) on the exposed

threads of the Bolt to clamp the Brace in place.

f. Hand tighten. See Figure F.

Leg Locking

Brace (6)

hook end of

Leg Locking

Brace (6)

Locking Knob (7)

Bolt (9)

Figure F

9. Install another Locking Brace and Bolt

to the opposite pair of legs.

10. Set the Sawhorse up on flat level ground.

Tighten any loose hardware. (This helps to

ensure that the sawhorse will sit level.)

11. Repeat the entire assembly procedure

with the other Sawhorse.

Page 5For technical questions, please call 1-888-866-5797.Item 61700

Operation

Read the ENTIRE IMPORTANT SAFETY INFORMATION section

at the beginning of this manual including all text under subheadings therein

before set up or use of this product.

Inspect tool before use, looking for damaged, loose, and missing parts.

If any problems are found, do not use tool until repaired.

Before use, double check that the Leg Locking Braces are securely attached to the bolts.

Set Up

1. Lay the Sawhorse on the ground, Wooden Board

face down. Pull the Legs out on each side.

2. Loosen both Locking Knobs.

3. Swing the Leg Locking Brace so that it catches

on the exposed Bolt. Repeat on other side.

4. Tighten both Locking Knobs.

5. Carefully turn over the Sawhorse.

6. Repeat on second Sawhorse.

7. WARNING! Conrm that the Leg Locking

Braces are securely attached to the Bolts

and all hardware is tight before every use.

Collapse

1. Loosen the Locking Knobs.

2. Lift up the hooked end of the Leg Locking Brace

and allow the Leg Locking Brace to dangle.

3. Repeat on the opposite side.

4. Close the Sawhorse Legs and

retighten the Locking Knobs.

Maintenance

Procedures not specifically explained in this manual must

be performed only by a qualified technician.

TO PREVENT SERIOUS INJURY FROM TOOL FAILURE:

Do not use damaged equipment. If damage is found, have the problem corrected before further use.

Cleaning, Maintenance, and Lubrication

1. BEFORE EACH USE, inspect the general

condition of the tool. Check for:

• loose hardware,

• misalignment or binding of moving parts,

• cracked or broken parts, and

• any other condition that may

affect its safe operation.

2. AFTER USE, wipe external surfaces

of the tool with clean cloth.

Page 6 For technical questions, please call 1-888-866-5797. Item 61700

Parts List and Diagram

Parts List (Parts for each sawhorse. 2 sawhorses included.)

Part Description Qty

1 Wooden Board 1

2 Leg Mounting Bracket 2

3 Leg 4

4 Brace 2

5 Foot 4

6 Leg Locking Brace 2

7 Locking Knob 2

8 Wood Screw 8

Part Description Qty

9 Bolt - M6 x 3/4" 12

10 Nut - M6 10

11 Nylon Insert Nut - M6 2

12 Washer 4

13 Split Lock Washer 2

14 Carriage Bolt - M5 x 5/16" 16

15 Nut - M5 16

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM

IN THIS DOCUMENT AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR

MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS

QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE

ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY

STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND

LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY

ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS

THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

Record Serial Number Here:

Note: If product has no serial number, record

month and year of purchase instead.

Note: Some parts are listed and shown for

illustration purposes only, and are not available

individually as replacement parts.

Page 7For technical questions, please call 1-888-866-5797.Item 61700

Assembly Diagram

612

715

3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (888) 866-5797

Limited 90 Day Warranty

Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,

and warrants to the original purchaser that this product is free from defects in materials and workmanship for the

period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,

to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper

installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries

to persons or property, or for incidental, contingent, special or consequential damages arising from the use of

our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the

above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER

WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.

To take advantage of this warranty, the product or part must be returned to us with transportation charges

prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.

If our inspection verifies the defect, we will either repair or replace the product at our election or we may

elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will

return repaired products at our expense, but if we determine there is no defect, or that the defect resulted

from causes not within the scope of our warranty, then you must bear the cost of returning the product.

This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

Inhaltsverzeichnis

Andere Central Machinery Rack & Stand Handbücher

Central Machinery

Central Machinery 42986 Bedienungsanleitung

Central Machinery

Central Machinery 94099 Bedienungsanleitung

Central Machinery

Central Machinery 59196 Montageanleitung

Central Machinery

Central Machinery 95128 Bedienungsanleitung

Central Machinery

Central Machinery 57289 Montageanleitung

Central Machinery

Central Machinery 66235 Bedienungsanleitung

Central Machinery

Central Machinery 46407 Installationshandbuch

Central Machinery

Central Machinery 96300 Stücklistenhandbuch

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung