Central Pneumatic 34844 Bedienungsanleitung

ASSEMBLYandOPERATINGINSTRUCTIONS

AIRBRUSHCOMPRESSOR

3491 Mission Oaks Blvd. / Camarillo, CA93011

No portion of this manual or any artwork contained herein may be reproduced in any

shape or form without the express written consent of Harbor Freight Tools.

For technical questions and replacement parts, please call 1-800-444-3353.

SPECIFICATIONS

SAVE THIS MANUAL

You will need the manual for the safety warnings and cautions, assembly instructions, operating

procedures, maintenance procedures, trouble shooting, parts list, and diagram. Keep your

invoice with this manual. Write the invoice number on the inside of the front cover. Keep both

this manual and your invoice in a safe, dry place for future reference.

SAFETY WARNING & CAUTIONS

WARNING: When using pneumatic equipment,basicsafety precautions should always befollowed

to reduce the risk of personal injury and hazards due to over pressurization.

READ ALL INSTRUCTIONS BEFORE USING THIS TOOL!

1. KEEP WORK AREA CLEAN. Cluttered areas invite injuries.

2. OBSERVE WORK AREA CONDITIONS. Do not use tools in damp, wet, or poorly lit

locations.Don’t expose to rain.Keep work area well lit.Do not use electrically powered air

compressors in the presence of flammable gases or liquids.

3. KEEP CHILDREN AWAY. Children must never be allowed in the work area.Do not let

them handle machines, tools, or hoses.

4. STORE IDLE EQUIPMENT. When not in use, tools must be locked up in a dry location

to inhibit rust. Always lock up tools and keep out of reach of children.

5. DO NOT FORCE THE TOOL. It will do the job better and more safely at the rate for

which it was intended. Do not use inappropriate attachments in an attempt to exceed the

tool’s capacities.

6. USETHERIGHTTOOLFORTHEJOB.Donotattempttoforceasmalltoolorattachment

to do the work of a larger industrial tool. Do not use a tool for a purpose for which it was not

intended.

7. DRESS PROPERLY. Do not wear loose clothing or jewelry as they can be caught in

movingparts.Non-skidfootwearisrecommended.Wear restrictive hair coveringto contain

long hair.

Air Pressure Rating 30PSI

Air Production 2CFM

Motor 1/8 HP, 115V, .6 amps

AirOutlet 1/8" NPT

Page 2 -- SKU: 34844 REV 10/04

8. USE EYE AND EAR PROTECTION. Always wear ANSI approved chemical splash

goggleswhenworkingwithchemicals.AlwayswearANSI approved impact safety goggles

atother times.Wear a full face shield if youare producingmetal filings or wood chips.Wear

anANSI approveddustmask orrespiratorwhen workingaroundmetal, wood,andchemical

dusts and mists.

9. DO NOT ABUSETHE POWER CORD. Do not yankcompressor’s cord to disconnect it

from the receptacle. Do not carry tools by the cord.

10. DO NOT OVERREACH. Keep proper footing and balance at all times. Do not reach

over or across running machines.

11. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and safer

performance. Follow instructions for lubricating and changing accessories. Inspect

compressor’s cord periodically and, if damaged, have them repaired by an authorized

technician. Inspect all hoses for leaks prior to use.The handles must be kept clean, dry,

and free from oil and grease at all times.

12. REMOVE ADJUSTING KEYS AND WRENCHES. Make it a habit to check that keys

andadjusting wrenchesareremoved fromthetool or machineworksurface beforeplugging

it in.

13. AVOID UNINTENTIONAL STARTING. Do not carry any tool with your finger on the

trigger, whether it is connected to the compressor or not.

14. STAY ALERT. Watch what you are doing;use common sense.Do not operate any tool

when you are tired.

15. CHECK DAMAGED PARTS. Before using any tool, any part that appears damaged

shouldbecarefullycheckedtodeterminethat itwill operateproperly andperform itsintended

function. Check for alignment and binding of moving parts; any broken parts or mounting

fixtures;and anyother condition that mayaffect proper operation.Anypart that is damaged

should be properly repaired or replaced by a qualified technician. Do not use the tool if any

switch does not turn on and off properly.

16. REPLACEMENT PARTS AND ACCESSORIES. When servicing, use only identical

replacement parts. Use of any other parts will void the warranty. Only use accessories

intended for use with this tool. Approved accessories are available from Harbor Freight

Tools.

17. DO NOT OPERATETOOL IF UNDERTHE INFLUENCE OF ALCOHOL OR DRUGS.

Readwarning labels onprescriptionstodetermine if yourjudgmentor reflexes are impaired

while taking drugs. If there is any doubt, do not operate the tool.

18. DRAIN COMPRESSOR EVERY DAY. Do not allow moisture to build up inside the

compressor.Do not allow compressor to sit pressurized for longer than one hour.

19. Make sure that regulator is set at least 10 PSI lower than the lowest rated piece of

equipment you are using.

Page 3 -- SKU: 34844

VOLTAGE WARNING

Before connecting the tool to a power source (receptacle, outlet, etc.) be sure the voltage

suppliedis about the same asthat specified on the nameplateof the tool. If one says 120V andthe

othersays110Vthenthere will be nocomplications.Never try to pluga110V tool into a220Voutlet,

or the other way around. The plug and outlet have completely different shapes. This is because a

power source with a voltage greater than that specified on the tool can result in a SERIOUS

INJURY to the user— as well as damage to the tool. If in doubt, DO NOT PLUG IN THE TOOL.

Using a power source with voltage (110V) less than the nameplate rating (220V) is harmful to the

motor.

EXTENSION CORDS

If your tool is double insulated and has a two-prong plug, you may use either a two- or

three-prong extension cord. If your tool has a grounded, three-prong plug, you must use a three-

prong extension cord with three-prong receptacles. Only use rounded jacket extension cords,

preferablylisted by the UnderwritersLaboratories (UL). Make surethe cord is ratedfor outdoor use

if you plan on using the tool outside; if you plan on indoor use, you may also use an outdoor rated

cord. Extension cords rated for outdoor use have the letters “WA” on the cord jacket.

Theextension cord must have aminimum wire size depending on the amperage ofthe tool

and the length of the extension cord. This size is signified by its AWG (American Wire Gauge)

rating; the smaller the gauge, the greater the cable’s capacity. If you are using two or more cords,

the total length of the combined cords must be used to determine the minimumAWG rating. Each

of the cords used must meet this rating.

The chart below is used to determine the rating required according to the length of the

cord(s). The amps of your tool are found either in this manual, or on the nameplate of the tool.

AMP

RATING 25 50 75 100 125 150 175 200

0-10.0 18 18 16 16 14 14 12 12

10.1-13.0 16 16 14 14 14 12 12 12

13.1-15 14 14 12 12 12 12 12 __

15.1-18 12 12 12 12 12 12 __ __

Always inspect extension cords for any damage. If there are any loose, frayed or exposed wires,

damaged insulation, or defective connections, replace the cord. Harbor Freight Tools can supply

UL listed and outdoor rated cords in multipleAWG ratings if needed.

TOTAL EXTENSION CORD(S) LENGTH IN FEET

Page 4 -- SKU: 34844

UNPACKING

When unpacking your Air Brush Compressor, check the items against the list below. If any

parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this

manual.

Item# Description Qty

N/A Air Compressor Assembly 1

N/A BrassAdapter Fitting 1

7 AirConduit 1

ASSEMBLY

Step 1:Remove the contents of the box and place on a clear work area.

Step 2:Place the JET PEN HOLDER (#10) onto the end of the HANDLE (#9) as shown in

Figure1.

Figure 1 — Placing the Jet Pen Holder

Page 5 -- SKU: 34844

Step 3:Remove the Brass Fitting from the Air Outlet Nipple on the Air Brush Compressor

as shown in Figure 2.

Figure 2 — Attaching the Air Conduit

Step 4:Place the Brass Fitting removed in Step 3 onto the bare end of the AIR CONDUIT

(#7). Makesurethethreads oftheBrassFitting face towardtheend of theAIRCONDUIT.

Step5:Placethe bare end of the AIRCONDUITovertheendof the Air Outlet Nipple. Make

sure the AIR CONDUIT is pressed over the ridge in the Air Outlet Nipple as shown in

Figure 2.

Step6:ThreadtheBrass FittingfromStep 4onto thethreadsof theAir OutletNipple. Tighten

snuggly, but do not over tighten as you may damage the AIR CONDUIT.

Your Air Brush Compressor is ready for use.

OPERATION

Step 1:Connect your air brush to the Brass Fitting at the end of the AIR CONDUIT (#7).

Tighten as appropriate.

Step 2:Plug the Power Cord into an appropriate outlet.

Step 3:To operate the Air Brush Compressor, flip the Switch to the ON or “l” position.

Page 6 -- SKU: 34844

MAINTENANCE

While operating theAir Brush Compressor, make sure the AIR INLET (#8) and the Motor Fan are

free of obstructions.

Periodicallyremove theAIRINLETfrom theAirBrush Compressor. TheAIRINLET’S foam rubber

serves as a filter for purifying the air. Make sure it is clean at all times.

There are no user-serviceable parts in yourAir Brush Compressor. If you need service performed

on your Compressor, please return it to Harbor Freight Tools.

DIAGRAM

PARTS LIST

Item# Description Qty Item# Description Qty

2 Compressor 1 9 Handle 1

7 AirConduit 1 10 Jet Pen Holder 1

8 AirInlet 1

Page 7 -- SKU: 34844

Inhaltsverzeichnis

Andere Central Pneumatic Luftkompressor Handbücher

Central Pneumatic

Central Pneumatic 61693 Montageanleitung

Central Pneumatic

Central Pneumatic CentralPneumatic 69269 Montageanleitung

Central Pneumatic

Central Pneumatic 60637 Montageanleitung

Central Pneumatic

Central Pneumatic 90749 Bedienungsanleitung

Central Pneumatic

Central Pneumatic 93785 Bedienungsanleitung

Central Pneumatic

Central Pneumatic 98635 Installationshandbuch

Central Pneumatic

Central Pneumatic 93657 Montageanleitung

Central Pneumatic

Central Pneumatic 93271 Bedienungsanleitung

Central Pneumatic

Central Pneumatic 04169 Bedienungsanleitung

Central Pneumatic

Central Pneumatic 60567 Original Bedienungsanleitung

Central Pneumatic

Central Pneumatic Central Pneumatic 30 Gallon, 180 PSI Gas Powered Two-Stage Air... Bedienungsanleitung

Central Pneumatic

Central Pneumatic 67847 Original Bedienungsanleitung

Central Pneumatic

Central Pneumatic 96068 Installationshandbuch

Central Pneumatic

Central Pneumatic 95386 Bedienungsanleitung

Central Pneumatic

Central Pneumatic 62913 Montageanleitung

Central Pneumatic

Central Pneumatic 92403 Stücklistenhandbuch

Central Pneumatic

Central Pneumatic 96469 Installationshandbuch

Central Pneumatic

Central Pneumatic 67708 Installationshandbuch

Central Pneumatic

Central Pneumatic 9592 Bedienungsanleitung

Central Pneumatic

Central Pneumatic 97080 Bedienungsanleitung

Central Pneumatic

Central Pneumatic CENTRAL PNEUMATIC 95499 Stücklistenhandbuch

Central Pneumatic

Central Pneumatic 94667 Bedienungsanleitung

Central Pneumatic

Central Pneumatic 90385 Bedienungsanleitung

Central Pneumatic

Central Pneumatic 61489 Bedienungsanleitung

Beliebte Luftkompressor Handbücher anderer Marken

Sparmax

Sparmax DC-25XR Bedienungsanleitung

KAESER

KAESER M122 Bedienungsanleitung

GMC

GMC GAC1500 Bedienungsanleitung

Briggs & Stratton

Briggs & Stratton Air Compressor Bedienungsanleitung

Fini

Fini F3GST2TK Bedienungsanleitung

Industrial Air

Industrial Air CP1580325 Programmierhandbuch

Campbell Hausfeld

Campbell Hausfeld RP3300 Kurzanleitung

Ingersoll-Rand

Ingersoll-Rand UP6 20 HP Bedienungsanleitung

Hitachi

Hitachi EC99S Bedienerhandbuch

Parkside

Parkside PKO 270 A1 Bedienungsanleitung

Sullair

Sullair 185 Bedienungsanleitung

Clas Ohlson

Clas Ohlson QIE-ZTH-15 Bedienungsanleitung

Ferm

Ferm CRM1046 Bedienungsanleitung

BE AC153 Bedienungsanleitung

RIDGID

RIDGID OF25150A Bedienungsanleitung

Johnson Controls

Johnson Controls QUANTUM LX Handbuch

Sears

Sears Craftsman 919.167463 Bedienungsanleitung

Ring Automotive

Ring Automotive RAC700 Bedienungsanleitung