Central Pneumatic 46168 Bedienungsanleitung

AIR COMPRESSORAIR COMPRESSOR

AIR COMPRESSOR

3 HP3 HP

3 HP, 12 GAL, V, 12 GAL, V

, 12 GAL, V, 12 GAL, V

, 12 GAL, V-HEAD-HEAD

-HEAD-HEAD

-HEAD

ASSEMBLY AND OPERATING INSTRUCTIONS

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit ourWeb site at http://www.harborfreight.com

this manual or any artwork contained herein may be reproduced in any shape or

form without the express written consent of Harbor Freight Tools.

For technical questions and replacement parts,please call 1-800-444-3353

46168

REV 02/02

Page 2SKU 46168

Specifications

ITEM DESCRIPTION

Maximum Pressure 115 PSI with auto shut off

CFM 2.6 CFM @ 115 PSI; 3.0 @ 90 PSI;

3.4 CFM @ 70 PSI; 4.0 CFM @ 40 PSI

Tank Capacity 12 Gallons

Power Consumption 120 VAC, 60 Hz, single phase; 9.7 amps (no load),

20.2 amps (startup)

Motor 3 HP, 1750 RPM

Air Outlet 1/4 inch, NPT (Male)

Power Cord 6-foot, 14 AWG, 3-wire, 3-prong plug; U.L. approved

Features

- tank drain valve and air outlet

- thermal overload protection

- 0~200 PSI Air Pressure Gauge, 1/4"

- rear pneumatic tires, 8" (dia.)

- Clear view oil change window

SaveThis Manual

You will need the manual for the safety warnings and precautions, assembly instructions,

operating and maintenance procedures, parts list and diagram. Keep your invoice with this

manual. Write the invoice number on the inside of the front cover. Keep the manual and

invoice in a safe and dry place for future reference.

Safety Warnings and Precautions

WARNING: When using tool, basic safety precautions should always be followed to

reduce the risk of personal injury and damage to equipment.

Read all instructions before using this tool!

1. Keep work area clean. Cluttered areas invite injuries.

2. Observe work area conditions. Do not use machines or power tools in damp or wet

locations. Don’t expose to rain. Keep work area well lighted. Do not use electrically

powered tools in the presence of flammable gases or liquids.

3. Keep children away. Children must never be allowed in the work area. Do not let

them handle machines, tools, or extension cords.

4. Store idle equipment. When not in use, tools must be stored in a dry location to

inhibit rust. Always lock up tools and keep out of reach of children.

5. Do not force tool. It will do the job better and more safely at the rate for which it was

intended. Do not use inappropriate attachments in an attempt to exceed the tool

capacity.

Page 3SKU 46168

6. Use the right tool for the job. Do not attempt to force a small tool or attachment to

do the work of a larger industrial tool.There are certain applications for which this tool

was designed. Do not modify this tool and do not use this tool for a purpose for which

it was not intended.

7. Dress properly. Do not wear loose clothing or jewelry as they can be caught in

moving parts. Protective, electrically non-conductive clothes and non-skid footwear

are recommended when working. Wear restrictive hair covering to contain long hair.

8. Use eye and ear protection. Always wear ANSI approved impact safety goggles.

Wear a full face shield if you are producing metal filings or wood chips.Wear an ANSI

approved dust mask or respirator when working around metal, wood, and chemical

dusts and mists.

9. Do not overreach. Keep proper footing and balance at all times. Do not reach over

or across running machines.

10. Maintain tools with care. Keep tools sharp and clean for better and safer

performance. Follow instructions for lubricating and changing accessories. Inspect

tool cords periodically and, if damaged, have them repaired by an authorized

technician.The handles must be kept clean, dry, and free from oil and grease at all

times.

11. Disconnect power.Unplug tool when not in use.

12. Remove adjusting keys and wrenches. Check that keys and adjusting wrenches

are removed from the tool or machine work surface before plugging it in.

13. Avoid unintentional starting. Be sure the switch is in the Off position when not in

use and before plugging in.

14. Stay alert. Watch what you are doing, use common sense.Do not operate any tool

when you are tired.

15. Check for damaged parts. Before using any tool, any part that appears damaged

should be carefully checked to determine that it will operate properly and perform its

intended function. Check for alignment and binding of moving parts; any broken parts

or mounting fixtures; and any other condition that may affect proper operation. Any

part that is damaged should be properly repaired or replaced by a qualified

technician. Do not use the tool if any switch does not turn On and Off properly.

16. Guard against electric shock. Prevent body contact with grounded surfaces such

as pipes, radiators, ranges, and refrigerator enclosures.

17. Replacement parts and accessories. When servicing, use only identical

replacement parts.Use of any other parts will void the warranty. Only use accessories

intended for use with this tool. Approved accessories are available from Harbor

Freight Tools.

18. Do not operate tool if under the influence of alcohol or drugs. Read warning

labels on prescriptions to determine if your judgment or reflexes are impaired while

taking drugs. If there is any doubt, do not operate the tool.

Page 4SKU 46168

19. Use proper size and type extension cord. If an extension cord is required, it must

be of the proper size and type to supply the correct current to the tool without heating

up. Otherwise, the extension cord could melt and catch fire, or cause electrical

damage to the tool.This tool requires use of an extension cord of 0 to 20 amps

capability (up to 50 feet), with wire size rated at 12 AWG. Longer extension cords

require larger size wire. If you are using the tool outdoors, use an extension cord rated

for outdoor use.(signified by “WA” on the jacket).

21. Maintenance. For your safety, service and maintenance should be performed

regularly by a qualified technician.

22. Drain compressor every day. Do not allow moisture to build up inside the

compressor. Do not allow compressor to sit pressurized for longer than one hour.

23. Make sure all equipment is rated to the appropriate capacity. Do not use any air

tool that does not operate at 115 PSI.

24. Avoid explosions and fire. Never place flammable objects near the compressor.

Never spray water or any flammable liquids towards the compressor.

25. Avoid body injury. Never direct the air outlet at persons or animals.

Note: Performance of this tool may vary depending on variations in local line voltage. Exten-

sion cord usage may also affect tool performance.

Warning:The warnings, cautions,and instructions discussed in this instruction manual

cannot cover all possible conditions and situations that may occur. It must be under-

stood by the operator that common sense and caution are factors which cannot be

built into this product, but must be supplied by the operator.

Unpacking

When unpacking, check to make sure that all the parts are included. Refer to the Assembly

Drawing and Parts List at the end of this manual. If any parts are missing or broken, please

call Harbor Freight Tools at the number on the cover of this manual as soon as possible.

Operation

Warning: Fill with compressor oil before using; running with no or low oil voids war-

ranty. Optimal oil tank capacity is 8.8 ounces.

Oil Gauge

The Dip Stick (2) oil gauge is used to determine if oil is needed.

To check the oil:

1. Unscrew

(do not pull)

the Dip Stick out.

2. Check the level of the oil.

There are two lines on the bottom of the Dip Stick. The oil

level should always be at maximum.

Maximum

Minimum

(2)

REV 02/04

Page 5SKU 46168

3. Add 30-weight, non-detergent oil through the Gauge’s hole as necessary, but do not

overfill. Screw in the Oil Gauge, being careful not to strip the plastic threads.

Hose Connections

1. Close the Air ControlValve (7) (right or left).

2. Connect the high pressure air hose to the air outlet.

The outlet is 1/4” NPT. For easy connection or removal, a quick coupler (not supplied)

should be installed on the end of the outlet.

3. Turn the Air Control Valve to the middle position to allow the air to pass.

Warning: Do not remove the factory sealed Air Control Valve (7); removal voids war-

ranty.

Turning Compressor On

1. Plug the power cord into an electrical outlet with a grounding prong.

2. Pull up on the On/Off Pressure Switch (3) to turn on. Push down on

the Switch to shut off.

3. Allow the Tank to fill to 80 PSI before using.

With the Air Compressor turned on, operation is automatic and

under the control of the internal pressure switch.

Adjusting Pressure Switch

Caution:The internal pressure switch is adjustable but changes to the pressure levels

are not recommended; any change to the automatic On/Off pressure levels will cause

additional stress on the motor which may result in shortened motor life.

Using the Pressure ReliefValve

The Pressure Relief Valve (4) is used when decompression is

needed quickly and efficiently.

1. Press the On/Off Pressure Switch (3) down to turn power off.

2. Pull on the Pressure Release Valve (4) ring to release

pressure.

Empty Air and Condensation

The Water Spill Valve (11) is located underneath the AirTank.It must

be used daily to release all trapped moisture through this valve. It will also get rid of any

condensation that may cause tank corrosion.

Warning: Do not open the Water Spill Valve (11) so that more than four threads are

showing.

1. Push down on the On/Off Pressure Switch (3) to turn the compressor off. Unplug the

electrical plug.

On/Off

Switch

Cover 7

REV 02/04

Page 6SKU 46168

2. Unscrew theWater Spill Valve (11) two to three turns.

3. When all pressure is released, close the valve again. Plug in the electrical plug.

Maintenance

1. Check compressor oil level daily. Fill if necessary with 30-weight, non-detergent

oil.

2. Purge the AirTank daily of all air and moisture to prevent corrosion.

3. Store the Air Compressor in a clean and dry location.

4. Check all air fittings for leaks before using.

5. To extend the life of your air tools, it is recommended to install an oiler and water filter

in series with the air output line of the Air Compressor (sold separately) as shown

below.

NOTE: Some parts are listed and shown

for illustration purposes only and are not

availableindividuallyasreplacementparts.

PLEASE READTHE FOLLOWING CAREFULLY

THEMANUFACTURERAND/OR DISTRIBUTOR HASPROVIDEDTHEPARTSDIAGRAM INTHIS

MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBU-

TOR MAKES ANYREPRESENTATIONORWARRANTY OF ANYKINDTOTHE BUYERTHAT HE

OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TOTHE PRODUCT OR THAT HE OR SHE IS

QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER

AND/ORDISTRIBUTOREXPRESSLYSTATESTHATALLREPAIRSANDPARTSREPLACEMENTS

SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSEDTECHNICIANS AND NOT BYTHE

BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER

REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING

OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

Note: The Handle (#5) includes a flat plate which is designed to accept an air hose reel (not

included).

REV 02/02 REV 02/04

Page 7SKU 46168

Parts List No. 1

Item # Description

1 Discharge Pipe

2 Dip Stick

3 On/Off Pressure Power Switch

4 Pressure Relief Valve

5 Handle

7 Air Control Valve

8 Foot

9 Cord and Plug

10 Pressure Gauge

11 Water Spill Valve

12 Wheel

13 Air Tank

14 Fan Guide

15 Capacity Case

Assembly Drawing No. 1

REV 02/02

10 11 12

Page 8SKU 46168

Parts List No. 2

Item # Description

C22 Screw

C23 Washer

A37 Air Filter

A01 Cylinder Case

A31 Gasket

A45 Valve Seat

A48 Gasket

A04 Valve Plate

A49 Gasket

B01 Cylinder

B07 Cylinder Gasket

B03 Compressor Ring

B04 Scraping Oil Ring

B02 Piston

B05 Piston Ring

B06 Crankshaft Retainer

C15 Connecting Rod

C04 Crankshaft

D33 Front Cover

C24 Gasket

C01 Crankshaft Case

D25 Stator and Case

C09 Bearing

C06 Oil Seal

D28 Armature

D27 Back Cover

D29 Fan

D30 Screw

D31 Fan Guide

D01 Gasket

D02 Connector

D03 Capacity Case

D04 Capacity

D05 Capacity Case Cover

D07 Screw

D08 Washer

Page 9SKU 46168

Assembly Drawing No. 2

Inhaltsverzeichnis

Andere Central Pneumatic Luftkompressor Handbücher

Central Pneumatic

Central Pneumatic 60567 Original Bedienungsanleitung

Central Pneumatic

Central Pneumatic 95275 Installationshandbuch

Central Pneumatic

Central Pneumatic 61454 Bedienungsanleitung

Central Pneumatic

Central Pneumatic CENTRAL PNEUMATIC 95499 Stücklistenhandbuch

Central Pneumatic

Central Pneumatic 96068 Installationshandbuch

Central Pneumatic

Central Pneumatic PROFESSIONAL 99901 Bedienungsanleitung

Central Pneumatic

Central Pneumatic 68067 Montageanleitung

Central Pneumatic

Central Pneumatic 93271 Installationshandbuch

Central Pneumatic

Central Pneumatic 47915 Bedienungsanleitung

Central Pneumatic

Central Pneumatic 43520 Bedienungsanleitung

Central Pneumatic

Central Pneumatic 93657 Montageanleitung

Central Pneumatic

Central Pneumatic 62380 Montageanleitung

Central Pneumatic

Central Pneumatic CentralPneumatic 69269 Montageanleitung

Central Pneumatic

Central Pneumatic 04169 Bedienungsanleitung

Central Pneumatic

Central Pneumatic 96469 Installationshandbuch

Central Pneumatic

Central Pneumatic 96087 Stücklistenhandbuch

Central Pneumatic

Central Pneumatic 69667 Montageanleitung

Central Pneumatic

Central Pneumatic 93351 Bedienungsanleitung

Central Pneumatic

Central Pneumatic 93657 Montageanleitung

Central Pneumatic

Central Pneumatic 45214 Bedienungsanleitung

Central Pneumatic

Central Pneumatic 67696 Installationshandbuch

Central Pneumatic

Central Pneumatic CENTRAL PNEUMATIC 47407 Stücklistenhandbuch

Central Pneumatic

Central Pneumatic 60638 Bedienungsanleitung

Central Pneumatic

Central Pneumatic 98635 Installationshandbuch

Beliebte Luftkompressor Handbücher anderer Marken

Sparmax

Sparmax DC-25XR Bedienungsanleitung

KAESER

KAESER M122 Bedienungsanleitung

GMC

GMC GAC1500 Bedienungsanleitung

Briggs & Stratton

Briggs & Stratton Air Compressor Bedienungsanleitung

Fini

Fini F3GST2TK Bedienungsanleitung

Industrial Air

Industrial Air CP1580325 Programmierhandbuch

Campbell Hausfeld

Campbell Hausfeld RP3300 Kurzanleitung

Ingersoll-Rand

Ingersoll-Rand UP6 20 HP Bedienungsanleitung

Hitachi

Hitachi EC99S Bedienerhandbuch

Parkside

Parkside PKO 270 A1 Bedienungsanleitung

Sullair

Sullair 185 Bedienungsanleitung

Clas Ohlson

Clas Ohlson QIE-ZTH-15 Bedienungsanleitung

Ferm

Ferm CRM1046 Bedienungsanleitung

BE AC153 Bedienungsanleitung

RIDGID

RIDGID OF25150A Bedienungsanleitung

Johnson Controls

Johnson Controls QUANTUM LX Handbuch

Sears

Sears Craftsman 919.167463 Bedienungsanleitung

Ring Automotive

Ring Automotive RAC700 Bedienungsanleitung