Cervoz MEC-LAN-2002i Bedienungsanleitung

MEC-LAN-2002i

M.2 2242/2260/2280 2-port 10/100/1000 isolated Ethernet board

User’s Manual

First Edition, August 2021

Reproduction without permission is prohibited

M.2 2242/2260/2280 Ethernet Card

User’s Manual

The software described in this manual is furnished under a license agreement and may be

used only in accordance with the terms of that agreement.

prohibited.

Trademarks

Cervoz is a registered trademark of Cervoz Technology Co., Ltd. All other trademarks or

registered marks in this manual belong to their respective manufacturers.

Disclaimer

Information in this document is subject to change without notice and does not represent a

commitment on the part of Cervoz.

Cervoz provides this document “as is,” without warranty of any kind, either expressed or

implied, including, but not limited to, its particular purpose. Cervoz reserves the right to make

improvements and/or changes to this manual, or to the products and/or the programs

described in this manual, at any time.

Information provided in this manual is intended to be accurate and reliable. However, Cervoz

assumes no responsibility for its use, or for any infringements on the rights of third parties that

may result from its use.

This product might include unintentional technical or typographical errors. Changes are

periodically made to the information herein to correct such errors, and these changes are

incorporated into new editions of the publication.

Technical Support Contact Information

http://www.cervoz.com/contact.php

Cervoz Technology Co., Ltd.

Tel: +886-2-2911-9599

Fax: +886-2-2911-9566

Table of Contents

Chapter 1

Introduction

Overviews

Features

Installation Flowchart

Package Checklist

Chapter 2

Hardware Installation

Appendix

Pin Assignments

Board Side Pin Assignments

Device Side Pin Assignments

Technical Reference

MEC-LAN-2002i Specifications

MEC- LAN-2002i Dimensions

MEC- LAN-2002i Daughter Board Dimensions

Product Warranty Statement

Introduction

Overview

MEC-LAN-2002i is an Ethernet card for embedded PC. The card follows the M.2

standard which is compliant with PCI Express x 1 classification and M.2 form factor.

This board fits in any host computer that has M.2 slots. MEC- LAN-2002i is a highly

cost-effective solution to expand Gigabyte network for your computer.

Features

The PCI Express boards have the following outstanding features:

Single-Lane (x1) PCI-Express with throughput up to 5.0 / 2.5Gbps

Fully compliant with PCI-Express Base Specification Rev 2.0

Integrated 10/100/1000Mbps transceiver

IEEE 802.3, IEEE 802.3u, IEEE 802.3ab, and IEEE 802.3z compliant

IEEE 802.3x Full-Duplex flow control

Complies with EN61000-4-2(ESD) Air-15kV, Contact-8kV

Complies with EN61000-4-4(EFT) 2kV

Complies with EN61000-4-5 2kV Surge protection

Installation Flowchart

Installation Flowchart of MEC-LAN-2002i

The following flowchart provides a brief summary of the procedure you should follow to

install the M.2 card:

Package Checklist

The following items are included in the M.2 board package:

M.2 Card x 1

Daughter Board x 1

Bracket x 1

M2.5 Screw x 2

20Pin Internal Connection Cable (30cm) x 2

Quick Installation Guide (Printed) x 1

Note: Notify your sales representative if any of the above items are missing or

damaged.

Connect the internal cable

Hardware Installation

Install the card in the M.2 slot

Connector Fixation

Confirm if device is ready to be used

Hardware Installation

This chapter describes the PCI Express Series hardware installation procedure. Since the

BIOS automatically assign the PCI Express board’s IRQ number and I/O addresses, you must

plug in the board before installing the driver.

Step 1

Connect the internal cable to the card

Note

Both sides of the cable connectors are the same, it doesn’t matter which side

you connect

Step 2

Install the card to the M.2 slot

Make sure you install the card in the right position (fool-proof design)

Step 3

Fix the card on the motherboard

Make sure you tighten up the screws to fix the card.

Note

The product comes in the M.2 2280 form factor but can be broken off to

become a M.2 2260 or broken down further into a M.2 2242.

Step 4

Card installation completed

Step 5

Connect the cable to the daughter board

Connect other side of the cable to the daughter board

Note

Both sides of the cable connectors are the same, it doesn’t matter which side

you connect

Step 6

Confirm if device is ready to be used

Start “Computer Management” program

Go to the route: My Computer → Manage → Device Manager → Network adapters



is ready to be used

Connector Fixation

MECFIX –Versatile Mounting

1. Standard PCI/PCIe Bracket

PCI / PCIe IO Bracket

2. Low Profile PCI/PCIe Bracket

Low Profile IO Bracket

Inhaltsverzeichnis

Andere Cervoz Netzwerkkarte Handbücher

Cervoz

Cervoz MEC-LAN-M102i Bedienungsanleitung

Beliebte Netzwerkkarte Handbücher anderer Marken

FirstComm

FirstComm OBiWiFi5G Bedienungsanleitung

Sun Microsystems

Sun Microsystems Interface Adapter Bedienungsanleitung

TRENDnet

TRENDnet TU2-ETG Bedienungsanleitung

YASKAWA

YASKAWA SI-EN3 Bedienungsanleitung

Paradyne

Paradyne BitStorm 2600 IP DSLAM Bedienungsanleitung

Belkin

Belkin F5D7050 Bedienungsanleitung

3Com

3Com EtherLink 3C509B Bedienungsanleitung

TRENDnet

TRENDnet TEG-PCITX Bedienungsanleitung

Cisco

Cisco MC16E Bedienungsanleitung

Delta Electronics

Delta Electronics Braking Modules VFDB Series Bedienungsanleitung

TwinMOS

TwinMOS Booming Bedienungsanleitung

Dialogic

Dialogic Media Board DM/V1200BTEPEQ Bedienungsanleitung

Buffalo

Buffalo AirStation WLI-PCM-L11GP Bedienungsanleitung

National Instruments

National Instruments NI 9234 Bedienungsanleitung

Hama

Hama 49276 Bedienungsanleitung

Linksys

Linksys WCF54G - Wireless-G Compact Flash Card Bedienungsanleitung

Compaq

Compaq Wireless LAN 100 Bedienungsanleitung

Bose

Bose PowerMatch Dante Bedienungsanleitung