Challenge T-25LCD Bedienungsanleitung

Digital Home Safe

Always Read the Instruction Manual

NEVER LOCK YOUR SPARE OVERRIDE KEYS OR THE INSTRUCTION MANUAL IN THE SAFE.

ONCE THE BATTERIES DEPLETE, YOU WILL NEED TO USE THE KEYS TO OPEN THE SAFE.

SPARE KEYS ARE UNAVAILABLE!

THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING THE

OPERATION AND MAINTENANCE OF THE SAFE

COMPLETELY READ AND UNDERSTAND THE MANUAL BEFORE SECURING ITEMS IN THE SAFE

SAVE THIS MANUAL FOR FUTURE REFERENCE

MODELS: T-25LCD

SAFE DIAGRAM

-1-

Locking

knob

LCD (display)

Key lock

cover

(Yellow) #(Green)

Instructions

4 x ‘AA’

batteries

Back-up power supply

Override keys 4 x rawlbolts

Number

pad

Dia.1

NOTE: This safe is NOT re proof.

NOTE: This safe has no cash rating.

CONTENTS

1 X Instruction book

2 X Manual override keys

1 X Backup power supply

1 X Internal mat

4 X ‘AA’ Batteries

4 X Rawlbolts

SPECIFICATION

T-25LCD

SIZE : 35 (w) x 25 (h) x 25 (d) Cm

NET WEIGHT: 9.15Kgs

POWER SUPPLY: 4x ‘AA’ 1.5V Batteries

INTERNAL VOLUME: 21.72 Litre

IMPORTANT INFORMATION

This safe can be programmed with two sets of codes, User and Master. After opening the safe and

installing the batteries you should change the USER and MASTER PINS, from the factories pre-set

codes, for security reasons. You could give the user code to a guest while maintaining the master code.

OPERATING THE SAFE FOR THE FIRST TIME

Use the Manual override key to open the safe.

Remove the plastic key lock cover (dia 1).•

The number under the cover is the key number. Replacement keys are unavailable!•

Insert the override key; turn it anti-clockwise, at the same time turn the locking knob clockwise and pull•

open the safe.

See• BATTERY REPLACEMENT

Keep the safe door open until you have set the PIN code.•

LCD DISPLAY

To hide the numbers from being displayed when entered, Press “#” followed by “• “, then enter your

PIN. “o” will be displayed instead of the number.

-2-

KEY PAD

If you make a mistake when entering the PIN, press “• “, the last digit entered will be deleted.

Each time a button is pressed, a beep will be heard. This is a safety feature so that you will know when•

the safe is being accessed and cannot be switched off.

If you Press “• ”, “ bELL on” will be displayed. This will display the battery power status.

However, there is no function to switch the bELL (beep) off.

PROGRAMMING YOUR PIN NUMBER (personal identication number)

DEFAULT FACTORY USER PIN: 1234 : DEFAULT FACTORY MASTER PIN: 123456

Either of these PIN Codes can be set from 1 to 8 digits.

WE STRONGLY RECOMMEND THAT 4 OR MORE NUMBERS ARE USED AS THE USER CODE AND

6 OR MORE FOR THE MASTER CODE.

Keep PIN codes in a safe place. Do not use personal information like birthdays, telephone numbers etc.

NOTE: The following steps will only change one PIN, either the User or Master PIN based on the PIN

you entered in step 2.

In order to change the other PIN, simply repeat steps above, using the other code at step 2.

Write down your PIN codes so you do not forget it. (any combination of numbers from 4 to 8 digits)

Press “#”1.

Enter the either the User PIN or the Master2.

Press “#”3.

The safe will beep 3 times and display4.

“OPEN”.

Press “5. ” within 10 seconds.

The LCD will display “--------”.6.

Enter your New User or Master PIN7.

Press”#”8.

The LCD will display”--------”9.

Re-enter your New User or Master PIN.10.

Press “#”11.

The LCD will display “Into” for a few seconds12.

Your new PIN has been set.13.

While the door is open familiarise yourself with the door opening procedure, and leave the door open

untilyouaresatisedthatyoufullyunderstandtheopeningandclosingmethod.Youcanre-setthePIN

at any time by following the above procedure.

RESETTING THE PIN CODE TO THE FACTORY DEFAULTS

PIN CODES (personal identication number)

The safe can be reset back to the factory default PIN codes by

pressing the red button situated on the inside cover of the safe

door (Dia 2).

Open the safe door. Remove the reset button’s security cap by

unscrewing it.

Press the red reset button. The display will show “CLEAr”; all PIN

codes will revert back to the factory default PIN codes.

Pleaseretresetbutton’ssecuritycapforsecurityreasons.

OPENING THE DOOR USING YOUR PIN NUMBER (personal identication number)

Press ”#”•

Enter your PIN (either your user or master PIN code)•

Press “#”•

The safe will beep 3 times and display “OPEN”.•

Turn the locking knob clockwise within 10 seconds and pull the safe door open.•

If the PIN code is entered incorrectly the LCD will display “Error”. Wait for the display to clear and try•

again.

If the voltage of batteries is low the LCD will show “Lo-bAtt”. The batteries must be replaced.

Dia.2

Security cap

covering reset

button

OPENING THE SAFE USING THE OVERRIDE KEY

Use the Manual override key to open the safe.

Remove the plastic key lock cover (dia 3)•

Insert the override key; turn it anti-clockwise, at the same time•

turn the locking knob clockwise and pull open the safe.

BATTERY REPLACEMENT

The digital safe uses four ‘AA’ type batteries (supplied).

Remove the battery cover on the rear of the door (dia 4). Push•

the catch in and pull out the cover.

Install the 4x ‘AA’ batteries supplied (dia.4). Ensure correct•

polarity.

Replace the battery cover.•

The unit will beep, and the display will show “o” travelling from•

one side to the other followed by “ALLrEADY”. The unit is now

ready to be programmed.

Keep the safe door open until you have set the PIN code.•

Press #•

If the voltage of batteries is low, the LCD will show “Lo-bAtt”.•

The batteries must be replaced.

BATTERY PACK

Ifyourbatteriesareat,andyouareunabletondtheoverride

keys, you can use the Battery Pack to power the keyboard.

Fit four 1.5V ‘AA’ batteries in the battery pack. Plug the jack plug

of the pack into the battery backup socket on the panel of the

keypad. (dia.5).

The battery life is approximately one year.

Make a note of the battery replacement date; they should

last approximately one year.

However, we recommend checking the batteries every 6

months just to make sure.

If power is removed from the safe the set PIN code may

reset. If this happens use the factory default Pin codes.

SECURING YOUR SAFE

ADVICE: WE STRONGLY RECOMMEND THAT YOU SECURE

YOUR SAFE TO A WALL OR FLOOR FOR SECURITY

REASONS.

Youmaywishtosecureyoursafetoaxedpartofthehouse(i.e.

stone wall or wooden beam).

This can be achieved by using 2 of the 4 rawlbolts supplied in the

back of the safe or using the 4 rawlbolts in the base of the safe.

Use the holes in the safe to mark where you need to drill. Loosely

attach the rawlbolts onto the safe with the nuts and washers

provided. Hold the safe over the drilled holes and locate the

rawlbolts into these holes (Dia 6). Tighten the nuts from the inside

ofthesafetosecurermly.

Note : The rawlbolts are packed inside the safe

-3-

Dia.3

Dia.4

Dia.5

Dia.6

Back of safe

Wall

Nut & Washer

on the inside of

the safe

Dia.7

-4-

TROUBLE SHOOTING

PROBLEM CAUSE SOLUTION

1 Can I get a replacement key/

extra key?

Replacement keys are not

available due to security

reasons.

2 The keypad becomes

inoperable

Low or depleted batteries Use override keys or Battery

Pack and replace batteries.

3 My PIN works, however, the

safe won’t open

Low batteries. Will operate the

keypad but not the lock relay.

Use override keys or Battery

Pack and replace batteries.

4 I have lost the keys, battery

pack and forgotten the PIN

number, can I obtain spare key

or battery pack?.

Spare keys are unavailable,

but we can supply you with a

spare battery pack at a small

charge.

5 I am experiencing problems

using the back up key; it is

unable to slide smoothly into

the keyhole.

Spray inside the keyhole with

WD40, leave for a few minutes

and then try again.

6 We recently changed the

batteries in the safe, the safe

has reset the code itself, and

the code I’ve been using is no

longer valid?

If the batteries are completely

depleted for more than a day

then the safe will not retain the

code.

Try the factory default code

or use the override key; then

refer to the user manual to

reset your original code or to

enter a new code.

7 When I enter # the LCD

displays “Lo-bAtt”.

The batteries are depleted. Immediately replace the

batteries.

8ThebatteriesIboughtdon’tt

the safe?

Batteries can vary in size. Try another brand.

9 When I use the override key, I

can’t open the door.

Ensure that you are tuning the

key anti-clockwise, holding it

in that position and then turn

the locking knob clockwise to

release the catch.

IB-T-25LCD-Issue1-04-04-11

HELPLINE

In the unlikely event of a defect occurring please contact our Helpline.

Ofcehours9am–4pm,Monday-Friday.Outsideofcehoursorduringpeaktimesyouwillbe

directed to an

answer phone. Please leave your name, a brief description of your enquiry and your number.

One of our operators will contact you as soon as possible.

Telephone Number 02083 916 767

Alternatively check the Q&A on our website www.hilka.co.uk/faq.php

NOTE:

These important safeguards and instructions cannot cover all possible conditions and situations

that may occur. It must be understood that common sense and caution are factors, which cannot

be built into any product. These factors must be supplied by the person using this product.

Manufactured on behalf of Home Retail Group

489 - 499 Avebury Boulevard,

Central Milton Keynes,

MK9 2NW

Inhaltsverzeichnis

Andere Challenge Sicherheitsprodukt für Zuhause Handbücher

Challenge

Challenge S-43LCD(II)A Bedienungsanleitung

Beliebte Sicherheitsprodukt für Zuhause Handbücher anderer Marken

First Alert

First Alert Fire Escape Ladder EL52W-2 Bedienungsanleitung

AOSafety

AOSafety GoggleGear Dust Bedienungsanleitung

Westfalia

Westfalia 69 86 96 Bedienungsanleitung

Summer

Summer 7260 Bedienungsanleitung

LST

LST M400DKMB-AS Bedienungsanleitung

FireAngel

FireAngel WFS-627 Bedienungsanleitung

Samsung

Samsung SSA-R2001 Bedienungsanleitung

Hydreon

Hydreon FakeTV FTV-10 Bedienungsanleitung

KIDPRO

KIDPRO Monofilament net Abmessungen und Installationsanleitung

Fiessler

Fiessler ESPE Type 4 Bedienungsanleitung

Maretron

Maretron MD-6517-N Bedienungsanleitung

LST

LST MGE8-1 Bedienungsanleitung

P3 International

P3 International Mini Bug Detector P7050 Bedienungsanleitung

FireAngel

FireAngel Stove Guard SGEL-SN-1 Bedienungsanleitung

Smanos

Smanos PB1000 Bedienungsanleitung

Innohome

Innohome SGK4010 Bedienungsanleitung

Pima

Pima RMC Series Bedienungsanleitung

Mustang Survival

Mustang Survival MD3183 Bedienungsanleitung