Chamberlain RED/GREEN LIGHT CONTROL KIT Bedienungsanleitung
1
RED/GREEN LIGHT
CONTROL KIT
FOR USE WITH LOGIC 2 OR 3 MODEL APT, T, AND GT OPERATORS
ACCESSORY P/N: RDGRNCARD
To prevent possible SERIOUS INJURY or DEATH from
electrocution, disconnect electric power to operator BEFORE
installing.
ALL electrical connections MUST be made by a qualified
individual.
Step 1
Step 4
Side View
Red/Green
Light Control
Module
Logic Board
Electrical Box
Step 3
Step 2
INSTALLATION
MOUNT THE LIGHT BOX
STEP 1:
Attach mounting bracket to the electrical box with the
self-threading screws (2) provided.
STEP 2:
Remove light box cover. Fasten light box to mounting bracket
with self-threading screws (2) provided.
STEP 3:
Attach flex conduit to electrical box.
STEP 4:
Insert Red/Green Light Control Module into either of the two
slots located on the logic board (see step 4 illustration).
NOTE: To avoid damage to relays, do not exceed the following:
• Red light output - 75W, 120V incandescent bulb or 3A,
250VAC (Resistive load).
• Green light output - 75W, 120V incandescent bulb or 3A,
250VAC (Resistive load).
WARNING: This product can expose you to chemicals including
lead, which are known to the State of California to cause
cancer or birth defects or other reproductive harm. For more
information go to www.P65Warnings.ca.gov
2
LOGIC 2
To Program open Mid-Stop:
1. Close the door.
2. Set dip switches to "Set Mid-Stop".
3. Press open (the door will begin moving).
4. Press stop when the desired Mid-Stop height is reached.
5. Return the dip switches to the desired wiring type (C2, B2,
etc.). The door will now stop at this height every time the door
is opened.
WARNING DEVICES MODULE
LOAD
R7
D3
D4
1
+5V +24V
OUT
+24VDC
D2
Q2
K2
R4
3
2
1
R2
Q1
D1
R6
Q3
C1
R8
C2
K1
J1
10 84
3
1
TB1
R8
R9
R1
R3
R5
13 +
TB2
RED
LT.
GREEN
LT.
120V IN
L1 L2
Figure 1
Light
Light box conduit w/wires Power LEDs 24 Vdc for Horn/Strobe
115 Vac power only
SET
MID-STOP
ON
OFF
STEP 5: (FIGURE1)
Complete wiring connections as follows:
• Connect red wire to red light terminal on the Red/Green Light
Control Module connector.
• Connect black wire to green light terminal on the Red/Green
Light Control Module connector.
• Connect white wire to L1 (NEUTRAL) on the power terminal
strip.
• Connect black jumper from L2 (HOT) on the power terminal
strip to (120V IN) terminal on the Red/Green Light Control
Module connector.
STEP 6:
Install red and green light bulbs (not provided). Maximum
wattage should not exceed 75 watts.
OPTIONAL MID-STOP PROGRAMMING:
LOGIC 3
To Program open or down (close) Mid-Stop:
1. Open the door to set close Mid-Stop or close door to set open
Mid-Stop.
2. Turn selector dial to “PROGRAM.”
3. Press the “MID SET” button on logic board.
4. Press the OPEN button for open Mid-Stop, wait until the door
reaches the desired Mid-Stop height, then press the STOP
button.
OR
Press the CLOSE button for down Mid-Stop, wait until the
door reaches the desired Mid-Stop height, then press the
STOP button.
5. Press the MID SET button to complete programming.
6. Turn selector dial back to desired wiring type.
1 2 3 4
1 2 3 4
Green
Light
Red
Light
Red
Red
WhiteWhite
Black
Black
3
LIGHT CONTROL MODULE OPERATION
The green lights on the option board will turn on if the board is
seated properly and the power is on. When the door reaches the
full open position or programmed mid-stop, the timer circuit will
be activated. The green lamp holder will receive power. If the
timer has not been set, the red lamp holder will receive power
when the door starts to close and until close limit is activated. If
the timer has been set, the red lamp holder will receive power as
indicated by the chart below.
NOTE:
A) The green lamp holder will never receive power if the timer is
set to ten seconds or less. The red lamp holder will blink for one
second on and one second off whenever the door is moving,
even if the timer to close has not been programmed.
B) The 24 Vdc output is for the addition of an optional Horn/
Strobe. When the operator is running OPEN or CLOSE and the
RED warning light is flashing, the output will activate the Horn/
Strobe.
TIMER SETTING RED LAMP HOLDER
RECEIVES POWER
Greater than or equal to
10 seconds
10 seconds before door starts to
close and until close limit is
activated
Less than 10 seconds Immediately after reaching open
limit or mid-stop
Wiring Mode Up Mid-Stop Down Mid-Stop
B2, C2, E2 Stop movement, wait for user input:
3-Button Control Station will OPEN or
CLOSE on command Single Button
Control/Radio will OPEN on command.
Down Mid-Stop disabled
D1 Up Mid-Stop disabled Down Mid-Stop disabled
T, TS, FSTS Stop movement, wait for user input:
3-Button Control Station will OPEN or
CLOSE on command Single Button
Control/Radio will OPEN on command. If
timer to close set is set for up Mid-Stop,
timer to close will close the door
Stop movement, then count down timer to close timer & auto
close
OR
User input during timer to close countdown:
3-Button Control Station will OPEN the door, CLOSE the door, or
STOP the countdown
Single Button Control will CLOSE on command
Radio will OPEN on command
Red/Green enabled at Mid-Stop
Failsafe B2, Failsafe C2 Stop movement, wait for user input:
3-Button Control Station will OPEN or
CLOSE on command
Single Button Control/Radio will OPEN
open command
Down Mid-Stop disabled
Failsafe D1 Up Mid-Stop disabled Down Mid-Stop disabled
Failsafe E2 Stop movement, wait for user input:
3-Button Control Station will OPEN or
CLOSE on command
Down Mid-Stop disabled
©2006, The Chamberlain Group, Inc.
All Rights Reserved
01-31098E
Andere Chamberlain Controller Handbücher
Chamberlain
Chamberlain Motorlift GWUP180 Bedienungsanleitung
Chamberlain
Chamberlain Liftmaster PROFESSIONAL 412-315HM Bedienungsanleitung
Chamberlain
Chamberlain T Bedienungsanleitung
Chamberlain
Chamberlain 811LM Bedienungsanleitung
Chamberlain
Chamberlain myQ 821LM Bedienungsanleitung
Chamberlain
Chamberlain MyQ Bedienungsanleitung
Chamberlain
Chamberlain 855CB Bedienungsanleitung
Chamberlain
Chamberlain Dial Code Bedienungsanleitung
Chamberlain
Chamberlain 945C Bedienungsanleitung
Chamberlain
Chamberlain SMART GARAGE CONTROL Bedienungsanleitung
Chamberlain
Chamberlain SECURITY+ WPB3LM3 Bedienungsanleitung
Chamberlain
Chamberlain CAP2D Bedienungsanleitung
Chamberlain
Chamberlain 320LM Bedienungsanleitung
Chamberlain
Chamberlain SUB324M Bedienungsanleitung
Chamberlain
Chamberlain 41A6127 Bedienungsanleitung
Chamberlain
Chamberlain Security+ CLLA1 Bedienungsanleitung
Chamberlain
Chamberlain Motorlift GWAP120 Bedienungsanleitung
Chamberlain
Chamberlain CLDM1ANZ Bedienungsanleitung
Chamberlain
Chamberlain 883LMW Bedienungsanleitung
Chamberlain
Chamberlain Security+ 974-315CB Bedienungsanleitung
