Chamberlain CAP2D Bedienungsanleitung

myQ®BusinessTM

Connected Access Portal 2-Door Controller

INSTALLATION MANUAL

Model CAP2D

PRE-INSTALL NETWORKWIRING ACCESS CONTROLINTRODUCTION INSTALL

INTRODUCTION PRE-INSTALL NETWORKWIRING ACCESS CONTROL INSTALL

INTRODUCTION

Safety............................................................................ 3

Controller Overview....................................................... 4

Control Board Overview ................................................ 4

Carton Inventory ........................................................... 5

Tools Needed ................................................................ 5

Dimensions................................................................... 5

Speciﬁcations................................................................ 6

Electrical Ratings........................................................... 6

Wire Speciﬁcations ....................................................... 7

PRE-INSTALL

Internet Service............................................................. 8

CP# for Controller ......................................................... 8

Setup a myQ®Business™ Account ............................... 8

Mount the Bracket......................................................... 9

WIRING

1SETUP 2INSTALL 3CONNECT 4ADD DEVICES

1SETUP 2INSTALL

3CONNECT 4ADD DEVICES

Connect Power............................................................ 10

NETWORK

1SETUP 2INSTALL 3CONNECT 4ADD DEVICES

1SETUP 2INSTALL

3CONNECT 4ADD DEVICES

Connect Internet.......................................................... 11

ACCESS CONTROL

1SETUP 2INSTALL 3CONNECT 4ADD DEVICES

1SETUP 2INSTALL

3CONNECT 4ADD DEVICES

Admin Mode................................................................ 12

Wiring REX and Doors ................................................ 12

Operation .................................................................... 14

Gate Access................................................................. 15

Door Access................................................................ 16

1SETUP 2INSTALL 3CONNECT 4ADD DEVICES

1SETUP 2INSTALL

3CONNECT 4ADD DEVICES

Conﬁguration Sheet.................................................... 18

Legal Disclaimers...................................................... 19

Warranty..................................................................... 19

INSTALL

1SETUP 2INSTALL 3CONNECT 4ADD DEVICES

1SETUP 2INSTALL

3CONNECT 4ADD DEVICES

Install the CAP2D ........................................................ 17

Troubleshooting.......................................................... 18

1SETUP 2INSTALL 3CONNECT 4ADD DEVICES

1SETUP 2INSTALL

3CONNECT 4ADD DEVICES

For myQ®Business™ programming, please visit www.myqbusiness.com

To reduce the risk of SEVERE INJURY or DEATH:

• Disconnect power at the fuse box BEFORE proceeding.

• To AVOID damaging gas, power or other underground utility

lines, contact underground utility locating companies BEFORE

digging.

• ALL electrical connections MUST be made by a qualified

individual.

• ALL power and control wiring MUST be run in separate

conduit.

To protect against fire and electrocution:

• Disconnect power BEFORE installing or servicing controller.

• NEVER connect a keypad/reader or lock to doors without first

consulting the applicable fire code.

• You MUST consult with, and get approval from, local fire

officials BEFORE installing locks or devices on ANY doors that

may be fire exits.

• Use of egress push buttons may not be legal. Single action

exits may be required.

• ALWAYS obtain proper permits and approvals in writing

BEFORE installing equipment.

Safety

Safety Symbol and Signal Word Review

When you see these Safety Symbols and Signal Words on

the following pages, they will alert you to the possibility of

serious injury or death if you do not comply with the warnings

that accompany them. The hazard may come from something

mechanical or from electric shock. Read the warnings carefully.

When you see this Signal Word on the following pages, it will alert

you to the possibility of damage to your property or product if you

do not comply with the cautionary statements that accompany it.

Read them carefully.

MECHANICAL

ELECTRICAL

PRE-INSTALL NETWORKWIRING ACCESS CONTROLINTRODUCTION INSTALL

INTRODUCTION PRE-INSTALL NETWORKWIRING ACCESS CONTROL INSTALL

WARNING: This product can expose you to chemicals including lead, which are known to the State of California to cause cancer

or birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

UNDERWRITERS LABORATORIES (UL) COMPLIANCE

The CAP2D complies with the UL294 Standard for access control

units with the following restrictions:

• The system relay contacts shall not be conﬁgured in the fail

secure mode unless permitted by the local authority having

jurisdiction and shall not interfere with the operation of panic

hardware.

• The Ethernet port is for supplemental use only, the unit will

continue to operate standalone if the network connection is interrupted.

• This unit can be powered over Ethernet via PoE Compatible hardware. Where used, any PoE power source must be UL294 Listed.

• All interconnecting devices must be UL Listed.

DO NOT INSTALL THE SYSTEM IN THE FAIL SECURE MODE

UNLESS PERMITTED BY THE LOCAL AUTHORITY HAVING

JURISDICTION. Doing so may cause interference with the

operation of panic hardware.

PRE-INSTALL NETWORKWIRING ACCESS CONTROLINTRODUCTION INSTALL

INTRODUCTION PRE-INSTALL NETWORKWIRING ACCESS CONTROL INSTALL

LAN

ADMIN

DRY

RLY1

WET

PSE1

PoE

DRY

WET

RLY2

HRTBT

READER 1

IO 1

REX

COM

DOOR

RED GRN 12V BUZ GND D1 D0

IO 2

REX

COM

DOOR

READER 2

RED GRN 12V BUZ GND D1 D0

COM

-12IN+

Controller Overview

Control Board Overview

NETWORK LED

Orange LED: 100MBit Link

Blue LED: Network activity

Right Blue LED: Good connection to the network

ACTIVE LED

OFF/Solid: System is starting

Blinking: System operational.

STATUS LED

Solid: System has power

Control Board Connection Description

Administrative USB Connect Mini-USB cable to access administrative functions

LAN/PoE Connect to network. *May also carry 802.3af/at power

Backup Lithium Battery Battery preserves the system’s data during primary power outages

Local Heartbeat LED indicates proper function

Relay Indicator LED lights when relay is engaged (one per relay)

Power Conﬁguration Jumper selects between PoE or Wired Power Supply

FRONT VIEW

LAN

ADMIN

DRY

RLY1

WET

PSE1

PoE

DRY

WET

RLY2

HRTBT

READER 1

IO 1

REX

COM

DOOR

RED GRN 12V BUZ GND D1 D0

IO 2

REX

COM

DOOR

READER 2

RED GRN 12V BUZ GND D1 D0

COM

-12IN+

ADMINISTRATIVE USB

DOOR 1DOOR 2

Auxiliary Relay 1

Aux Relay 1 LED

Aux Relay 2 LED

Relay 1 LED

Relay 2 LED

REQUEST TO EXIT

STATUS 1

WIEGAND INPUT 1

REQUEST TO EXIT

STATUS 2

WIEGAND INPUT 2

POWER CONFIG

JUMPER

EXTERNAL 12V POWER

BACKUP LITHIUM COIN BATTERY

(CR1220)

LAN/PoE Connector

LOCAL HEARTBEAT LED

Primary Relay 1

Auxiliary Relay 2

Primary Relay 2

*NOTE: Compliance to IEEE 802.3, at or af, was not evaluated by UL.

PRE-INSTALL NETWORKWIRING ACCESS CONTROLINTRODUCTION INSTALL

INTRODUCTION PRE-INSTALL NETWORKWIRING ACCESS CONTROL INSTALL

• Door Controller

• USB Cable

• Diodes

• Installation Manual

Carton Inventory

Tools Needed

• PH2 Phillips Screwdriver

• Precision 1/8" Flat or PH0 Phillips Screwdriver

• 1/4" Nut Driver

• Drill/Driver

• 7/64" Drill Bit

• Hammer Drill Bits for Drill/Driver

• RJ45 Crimping Pliers

• Multimeter

• Measuring tape

• Conduit Bender

• Conduit Cutter/Reamer

• Hack Saw

• Center Punch Tool

• Hammer

Dimensions

4-1/2" (11.4 cm)

3" (7.6 cm) 1-1/4" (3.2 cm)

.36" (.9 cm)

PRE-INSTALL NETWORKWIRING ACCESS CONTROLINTRODUCTION INSTALL

INTRODUCTION PRE-INSTALL NETWORKWIRING ACCESS CONTROL INSTALL

Speciﬁcations

CAP2D Capacity Resident Capacity: 25,000 / Local Event History: 6,000

CAP2D Operating Temperature Range -31°F to 150°F (-35°C to 66°C)

CAP2D Operational Humidity 5% to 95% non-condensing

Storage and Shipping Temperature Range -40°F to <185°F (-40°C To <85°C)

Wiegand Inputs (2) *26-Bit SIA Standard, 30-Bit Sentex, 32-Bit Mifare, 37-Bit HID with Facility Code,

37-Bit Transcore. Also supports ASCII for Wiegand keypads.

2 Primary and 2 Auxiliary Relay Outputs SPDT

Accessory Compatibility Refer to the accessory page for compatible accessories

Network Compatibility 10/100 Ethernet

Wire Speciﬁcation RJ-45 Wired Ethernet

PoE Supply Connector Conﬁguration Alternative B

Electrical Ratings

POWER IN VOLTAGE POWER (MIN)

Auxiliary Input 12 VDC 13 Watts

Power Over Ethernet 44-57 VDC 13 Watts

POWER OUT VOLTAGE CURRENT (MAX)

Relays (wet) 12 VDC 750mA (combined)

Wiegand Readers 12 VDC 750mA (combined)

Relays (dry-inductive) 30 VDC (max) 2,000mA

NOTE: IP Door Controller is to be connected to UL Listed

Commercial 294 or 603 Power Supply for Auxiliary, or UL Listed

294/294b PoE Listed power supply for Power over Ethernet.

*NOTE: Only 26-bit is UL compatible.

Wire Speciﬁcations

Use this chart to pull wires in preparation of your installation.

DESCRIPTION OF WIRE RUN WIRE SPECIFICATION MAXIMUM RUN DISTANCE

Power Wire, secondary DC output 2-Conductor 14 AWG

2-Conductor 16 AWG

2-Conductor 18 AWG

Up to 60 feet (18.3 m)

Up to 37 feet (11.3 m)

Up to 24 feet (7.3 m)

Local Area Network (LAN)

CAT 5/6 Network Cable

8-Conductor, 24 AWG Twisted pair 328 feet* (100 m)

Door Strike/LiftMaster Gate Operator 2-Conductor 18-22 AWG Shielded 100 - 250 feet (30.5 - 76.2 m)

Magnetic Lock 2-Conductor 18-22 AWG 50 - 125 feet (15.2 - 38.1 m)

Dry Contact Closure (Most Gate Operators) 2-Conductor 18-22 AWG Shielded 500 - 2500 feet (152.4 - 762 m)

Exit Request (REX) 2-Conductor 18-22 AWG 500 feet (152.4 m)

Supervised Input 2-Conductor 18-22 AWG 500 feet (152.4 m)

Wiegand/Proximity Readers 7-Conductor 18-22 AWG Shielded 500 feet (152.4 m)

NOTE: Main power supply and control wiring MUST be run in separate conduits. Conduits must be UL approved for low and high

voltage. Refer to the NEC, ANSI/NFPA 70 for additional wiring requirements.

NOTE: Place the CAP2D unit within 500 feet of its associated electronic strike or latch. Monitoring Software is not UL evaluated.

Always provide power from a dedicated source. Plug provided transformer into an outlet wired to its own 10 Amp minimum circuit

breaker. This will prevent two problems:

• Other equipment cannot introduce spikes, noise, surges or dips into the power circuit that will affect the system.

• The system’s operation will not be affected if any other equipment develops a short circuit across the power line.

* CAT 5/6 NETWORK CABLE NOTES:

• For outdoor distances exceeding 140 feet (42.7 m), a UL497 compliant primary surge protector MUST be installed at

the controller.

• Distances exceeding 328 feet (100 m) can be accommodated with additional hardware. Contact Technical Support for more

information. Additional hardware was not evaluated under UL294.

PRE-INSTALL NETWORKWIRING ACCESS CONTROLINTRODUCTION INSTALL

INTRODUCTION PRE-INSTALL NETWORKWIRING ACCESS CONTROL INSTALL

1Internet Service

The controller MUST be configured with the proper network settings to operate.

PRE-INSTALL NETWORKWIRING ACCESS CONTROLINTRODUCTION INSTALL

INTRODUCTION PRE-INSTALL NETWORKWIRING ACCESS CONTROL INSTALL

(Located on a label on the housing)

2CP# for Controller

NETWORK

Internet service provider:

Automatic IP addressing: DHCP (default setting)

Static IP Addressing: Optional, requires connection to PC with USB (NOTE: Write down the following for future

reference: IP, Netmask, Gateway, Primary, Secondary, Server Port)

3Setup a myQ®Business™ Account

NOTE: If you have an existing myQ®account, your myQ®Business™ account will have the

same password.

1. If you do not have a myQ® Business™ Account, call LiftMaster Customer Care and myQ

business account creation at 877-247-6764 to activate a myQ® Business™ Service

account.

2. You will get a welcome email from LiftMaster. Accept the email invitation and register or

3. Set up the Facility and add residents and credentials (refer to the available Help in myQ®Business™).

4. Continue with the installation of the CAP2D in this manual.

CP# IPC-XX-XXXXX

IPC - _ _ - _ _ _ _ _

For myQ®Business™programming please visit www.myqbusiness.com

PRE-INSTALL NETWORKWIRING ACCESS CONTROLINTRODUCTION INSTALL

INTRODUCTION PRE-INSTALL NETWORKWIRING ACCESS CONTROL INSTALL

4Mount the Bracket

1. Install an electrical box in the desired mounting location.

NOTE: Use 4" square electrical box (minimum of 1 1/2" deep) with a single-gang plaster ring. Use Wiremold®V5744S or

BW35 for surface-mount installations.

2. Remove the bracket from the back of the CAP2D.

3. Mount the bracket to the electrical box.

4. Run all wiring to the electrical box.

5. Once all the wiring is completed, position the CAP2D in the bracket and secure it at the bottom with the provided screw.

Bracket

Electrical Box

DO NOT connect a DC power supply if

Power Over Ethernet (PoE) is selected

and connected. Board may be damaged

and is NOT covered under the warranty

Connect Power

• DO NOT power electronic strikes and

latches with the same power supply

used to power the access control panel;

doing so will cause DAMAGE to the

controller. Use ONLY a UL listed burglar

alarm or access control system to

power electronic strikes and latches.

• DO NOT connect the power supply to a

switched outlet or otherwise controlled

AC outlet.

• DO NOT connect the power supply to

the 120 Vac outlet until ALL wiring is

completed.

• Install the transient noise suppression

device (MOV) supplied with the

controller for AC powered devices and

Diode for DC powered devices.

USING A DC POWER SUPPLY:

The outlet for the controller MUST be an external dedicated 120 Vac outlet

located within 60 feet (18.3 m) cable run of the controller. This outlet is

recommended to be wired back to its own 10 Amp minimum circuit breaker.

1. Connect 14-18 AWG wire to the stripped secondary DC output wires on

the power supply. Black is negative and red is positive.

2. Connect the power supply wires to the +12IN- terminal block (red to +

and black to -).

3. Plug the power supply into a 120 Vac outlet after all connections have

been made.

USING PoE (POWER OVER ETHERNET):

1. Connect Ethernet cable to the LAN/PoE connection on the control board.

2. Move PoE jumper to Power over Ethernet (PoE) setting.

PRE-INSTALL NETWORKWIRING ACCESS CONTROLINTRODUCTION INSTALL

INTRODUCTION PRE-INSTALL NETWORKWIRING ACCESS CONTROL INSTALL

WIRE SPECIFICATION MAXIMUM RUN DISTANCE

14 AWG Up to 60 Feet (18.3 m)

16 AWG Up to 37 Feet (11.3 m)

18 AWG Up to 24 Feet (7.3 m)

PoE (Power Over Ethernet)

Jumper

Red = +

Black = -

LAN

(Ethernet)

Conector

-12IN+

on Control Board

120 Vac

Dedicated Outlet

Power Supply

Dedicated 10 Amp Minimum Circuit

Power Supply

Default

PoE Jumper

NOTE: IP Door Controller is to be

connected to UL Listed Commercial 294

or 603 Power Supply.

Andere Handbücher für CAP2D

Inhaltsverzeichnis

Sprachen:

Andere Chamberlain Controller Handbücher

Chamberlain

Chamberlain LiftMaster Professional 915LM Bedienungsanleitung

Chamberlain

Chamberlain myQ 821LM Bedienungsanleitung

Chamberlain

Chamberlain 811LM Bedienungsanleitung

Chamberlain

Chamberlain LA412UL Kurzanleitung

Chamberlain

Chamberlain Garos CS 300 Bedienungsanleitung

Chamberlain

Chamberlain Security+ 974CB Bedienungsanleitung

Chamberlain

Chamberlain 395LM Bedienungsanleitung

Chamberlain

Chamberlain SUB324M Bedienungsanleitung

Chamberlain

Chamberlain SMART GARAGE CONTROL Bedienungsanleitung

Chamberlain

Chamberlain 945C Bedienungsanleitung

Chamberlain

Chamberlain CB124EV Bedienungsanleitung

Chamberlain

Chamberlain 872 Series Bedienungsanleitung

Chamberlain

Chamberlain CAP2D Bedienungsanleitung

Chamberlain

Chamberlain 883LMW Bedienungsanleitung

Chamberlain

Chamberlain T Bedienungsanleitung

Chamberlain

Chamberlain 855CB Bedienungsanleitung

Chamberlain

Chamberlain Motorlift GWAP120 Bedienungsanleitung

Chamberlain

Chamberlain LA400UL Kurzanleitung

Chamberlain

Chamberlain CLLACD Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster Professional CB224 Bedienungsanleitung

Chamberlain

Chamberlain 772CB Bedienungsanleitung

Chamberlain

Chamberlain RED/GREEN LIGHT CONTROL KIT Bedienungsanleitung

Chamberlain

Chamberlain LA500UL Kurzanleitung

Chamberlain

Chamberlain Motorlift GWUP180 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch