Chamberlain LiftMaster MH5011U Bedienungsanleitung

Radio Receiver

Built on Board

315 MHz

Installation Date

MH 5011U

MHS 5011U

MGJ 5011U

MT 5011U

BMT 5011U

MJ 5011U

www.liftmaster.com

CONTACT INFORMATION

MEDIUM DUTY LOGIC

USER'S GUIDE

Congratulations on purchasing a quality, LiftMaster Medium Duty Commercial Door Operator. Your new operator is capable of operating

up to 12 cycles per hour or 50 cycles per day. It is equipped with a built in radio receiver that is compatible with our existing 315 MHz

product line as well as a Timer-to-Close (TTC) feature that can be enabled when LiftMaster Commercial Protector System®is installed

and aligned properly.

INTRODUCTION

DETERMINE THE WIRING TYPE

The functionality of this operator is based on the wiring type. The operator is shipped from the factory in standard C2 wiring type

(factory default). LIFTMASTER MONITORED ENTRAPMENT PROTECTION (LMEP) DEVICE IS REQUIRED.

NOTES:

• The LED on the logic board will blink once when in C2 and twice when in B2.

• The operator will automatically convert to B2 wiring when Monitored Entrapment Protection Device is installed. If the Monitored

Entrapment Protection Device is removed, the operator will go into a Restricted Close mode**. Turn power OFF and ON to reset wiring

type.

** Restricted close mode requires a constant pressure close command. The operator will begin closing after a 5 second delay and will

continue to close to the close limit switch. The operator will stop if the pressure to close is released before reaching the close limit.

BASIC PROGRAMMING

RECOMMENDED INSTALLATION: B2 WIRING TYPE WITH

MONITORED ENTRAPMENT PROTECTION DEVICE

• Momentary contact to open, close and stop.

• Open override that reverses when closing by any opening

device.

• Wiring for entrapment protection device to reverse.

NOTE: The operator will automatically convert to B2 wiring

when Monitored Entrapment Protection Device is installed. (See

accessories page for Monitored Entrapment Protection Devices.)

• Timer-to-Close (TTC) feature available.

Photoelectric Sensor

MONITORED ENTRAPMENT PROTECTION DEVICE

No Programming Required

Photoelectric Sensor

ALTERNATE INSTALLATION: C2 WIRING TYPE WITH MONITORED

ENTRAPMENT PROTECTION DEVICE

• Momentary contact to open and stop with constant pressure to

close.

• Open override that reverses when closing by any opening

device.

• Wiring for entrapment protection device to reverse.

NOTE: The operator will automatically convert to B2 wiring

when Monitored Entrapment Protection Device is installed. (See

accessories page for Monitored Entrapment ProtectionDevices.)

• Timer-to-Close (TTC) feature not available.

Press and hold the LEARN and CLOSE buttons until the LED

goes out (approximately 3 seconds).

MONITORED ENTRAPMENT PROTECTION DEVICE

To Program:

TTC

LED

AUX ANT

R27

TP1 C20

C29

R24

C21

C32

R25

C31

D14

C18

014A1030

^^^^

LEARN

1234567

LMEP1 LMEP2 INTRLKCOM STOP CLOSE OPEN

STOP CLOSE OPEN

AUXANT

Logic Board

Electrical Box

D14

LED

LEARN

12345 67

STOP CLOSE OPEN

ALTERNATE INSTALLATION: C2 WIRING TYPE WITHOUT

MONITORED ENTRAPMENT PROTECTION DEVICE

(FACTORY DEFAULT)

• Momentary contact to open and stop with constant pressure to

close.

• Open override that reverses when closing by any opening

device.

• Wiring for entrapment protection device to reverse.

NOTE: The operator will automatically convert to B2 wiring

when Monitored Entrapment Protection Device is installed.

(See accessories page for Monitored Entrapment Protection

Devices.)

• Timer-to-Close (TTC) feature not available.

NON-MONITORED ENTRAPMENT PROTECTION DEVICE

Sensing Edge

Remove any monitored entrapment protection devices.

Press and hold the LEARN and STOP buttons until LED goes

out (approximately 3 seconds).

Reset to FACTORY DEFAULT (C2) without Monitored Entrapment

Protection Device:

BASIC PROGRAMMING

DETERMINE THE WIRING TYPE

To Reset to B2 with Monitored Entrapment Protection Device:

Press and hold the LEARN and STOP buttons until the LED

goes out (approximately 3 seconds).

BASIC PROGRAMMING

D14

COM INTRLK STOP

LED

OPENCLOSE

TTC LEARN

LMEP1 LMEP2

234567

STOP CLOSE OPEN

R27

AUXANT

^^^^

AUXANT

D14

COMINTRLK STOP

LED

OPENCLOSE

TTC LEARN

LMEP1LMEP2

234567

STOP CLOSE OPEN

SINGLE BUTTON REMOTE CONTROL

Press and release

the LEARN button

(LED will light).

Repeat steps 1 and 2 for additional remote controls.

REMOTE CONTROLS

Built in 315 MHz radio receiver permits as many as 20 Security✚®remote controls or dip switch remote controls in any combination.

Press and hold the button on the remote control until the LED

ﬂashes rapidly, then release to complete programming (LED

will go out).

D14

COM INTRLK STOP

LED

OPENCLOSE

TTC LEARN

LMEP1 LMEP2

234567

STOP CLOSE OPEN

R27

AUXANT

^^^^

AUXANT

D14

COMINTRLK STOP

LED

OPENCLOSE

TTC LEARN

LMEP1LMEP2

234567

STOP CLOSE OPEN

TO ERASE ALL REMOTE CONTROLS

1Press and hold the

LEARN button (over

5 seconds) until the

LED goes out. All

programmed remote

controls will be

erased.

D14

COM INTRLK STOP

LED

OPENCLOSE

TTC LEARN

LMEP1 LMEP2

234567

STOP CLOSE OPEN

R27

D14

COM INTRLK STOP

LED

OPENCLOSE

TTC LEARN

LMEP1 LMEP2

234567

STOP CLOSE OPEN

R27

AUXANT

^^^^

AUXANT

D14

COMINTRLK STOP

LED

OPENCLOSE

TTC LEARN

LMEP1LMEP2

234567

STOP CLOSE OPEN

3-BUTTON REMOTE CONTROL TO OPERATE AS A WIRELESS 3-BUTTON CONTROL STATION

NOTE: The feature will use 3 of the 20 memory channels in the operator.

123

Press and hold

the LEARN button

(LED will light).

Press the desired

button on the logic

board (OPEN,

CLOSE or STOP).

Release both

buttons.

Press and hold the desired button of the remote

control until LED ﬂashes rapidly, then release.

Repeat steps 1 through 3 to program additional buttons.

ATTENTION

AVERTISSEMENT AVERTISSEMENT

AVERTISSEMENT

WARNINGWARNING

CAUTION

WARNING

PRECAUCIÓN ADVERTENCIA

ADVERTENCIAADVERTENCIA

RADIO OPERATION

MODE OPEN CLOSE STOP REVERSE WHILE

CLOSING

TTC RESET

B2XXXX

B2 with TTC X X (3-button remote) X X X when open

C2 X X X

To prevent possible SEVERE INJURY or DEATH:

• Install a LiftMaster Monitored Entrapment Protection (LMEP)

device.

• NEVER permit children to operate or play with door control

push buttons or remote controls.

• Activate door ONLY when it can be seen clearly, is properly

adjusted and there are no obstructions to door travel.

• ALWAYS keep door in sight until completely closed. NEVER

permit anyone to cross the path of closing door.

D14

COM INTRLK STOP

LED

OPENCLOSE

TTC LEARN

LMEP1 LMEP2

234567

STOP CLOSE OPEN

R27

AUXANT

^^^^

AUXANT

D14

COMINTRLK STOP

LED

OPENCLOSE

TTC LEARN

LMEP1LMEP2

234567

STOP CLOSE OPEN

Press and

release the

LEARN button

(LED will light).

BASIC PROGRAMMING

TIMER DEFEAT

The TTC can be temporarily disabled by pressing a STOP button. TTC will become enabled after the next open command.

123

CLEAR THE TIMER-TO-CLOSE (TTC)

D14

COM INTRLK STOP

LED

OPENCLOSE

TTC LEARN

LMEP1 LMEP2

234567

STOP CLOSE OPEN

R27

Press and hold

the TTC button

for 6 seconds.

D14

COM INTRLK STOP

LED

OPENCLOSE

TTC LEARN

LMEP1 LMEP2

234567

STOP CLOSE OPEN

R27

Release the

TTC button

(LED will go

out). The TCC

will no longer

be active.

D14

COM INTRLK STOP

LED

OPENCLOSE

TTC LEARN

LMEP1 LMEP2

234567

STOP CLOSE OPEN

R27

Press and

release the

TTC button.

D14

COM INTRLK STOP

LED

OPENCLOSE

TTC LEARN

LMEP1 LMEP2

234567

STOP CLOSE OPEN

R27

AUXANT

^^^^

AUXANT

D14

COMINTRLK STOP

LED

OPENCLOSE

TTC LEARN

LMEP1LMEP2

234567

STOP CLOSE OPEN

Press and hold

the LEARN button

(LED will light).

D14

COM INTRLK STOP

LED

OPENCLOSE

TTC LEARN

LMEP1 LMEP2

234567

STOP CLOSE OPEN

R27

Every press and release

of the STOP button

will add 5 seconds to

the Timer-to-Close.

Example: 30 second

TTC = 6 presses of the

STOP button.

D14

COM INTRLK STOP

LED

OPENCLOSE

TTC LEARN

LMEP1 LMEP2

234567

STOP CLOSE OPEN

R27

Press and release

the TTC button to

exit programming

mode. The LED

will ﬂash once per

5 seconds of timer

setting.

D14

COM INTRLK STOP

LED

OPENCLOSE

TTC LEARN

LMEP1 LMEP2

234567

STOP CLOSE OPEN

R27

Press and

release the

TTC button.

D14

COM INTRLK STOP

LED

OPENCLOSE

TTC LEARN

LMEP1 LMEP2

234567

STOP CLOSE OPEN

R27

AUXANT

^^^^

AUXANT

D14

COMINTRLK STOP

LED

OPENCLOSE

TTC LEARN

LMEP1LMEP2

234567

STOP CLOSE OPEN

Press and

release the

LEARN button

(LED will light).

TIMER-TO-CLOSE (TTC)

TO PROGRAM

Begin with door in fully closed position.

Timer-to-Close feature enables the operator to close from the open limit after a preset time, adjustable from 5 to 60 seconds. Requires

LiftMaster Monitored Entrapment Protection (LMEP) device.

12 4

123

TO VERIFY TIMER-TO-CLOSE (TTC) SETTING

The TTC will become active after completion of the next open cycle. NOTE: The LED does not indicate that timer is running.

D14

COM INTRLK STOP

LED

OPENCLOSE

TTC LEARN

LMEP1 LMEP2

234567

STOP CLOSE OPEN

R27

Press and release the TTC button a

second time. The LED will ﬂash once

per 5 seconds of timer setting.

Requires B2 wiring type and compatible LiftMaster remote control.

In C2 wiring the remote control will open the door only.

Press remote control button.

Door should open. Allow the door to fully open.

Press remote control button.

Door should close. Allow door to fully close.

TESTING

Turn on power, LED will ﬂash 4 times on power up. Test all controls and entrapment protection devices to make sure they are working

properly. It may be necessary to refer back to the Adjustment section for adjustment of the limits.

IMPORTANT NOTES:

• Do not leave power to the operator on unless all entrapment protection devices have been tested and are working properly.

• Be sure you have read and understand all safety instructions included in this manual.

• Be sure the owner or person(s) responsible for operation of the door have read and understand the safety instructions, know how to

electrically operate the door in a safe manner and how to manually disconnect the door from the operator.

Press OPEN button. (The door should move in the open

direction.)

Press STOP button. (The door should stop.)

Press CLOSE button. (The door should move in the close

direction.)

Release CLOSE button. Door should stop if in C2 mode.

(The door should continue closing if in B2 mode.)

Press STOP button. (The door should stop.)

TEST 3-BUTTON CONTROL STATION

Press OPEN button. (The door should open.)

Allow the door to fully open.

Press CLOSE button. (The door should close.)

Allow the door to fully close.

If the limits are not set properly, remove power and adjust limits

(refer to installation manual).

TEST LIMIT ADJUSTMENT

Open the door.

Place an obstruction in the path of the photoelectric sensors

or sensing edge.

Press the CLOSE button. The door should not close if

photoelectric sensors are installed. The door should close to

obstruction and reverse if sensing edge is installed.

Remove the obstruction.

Press CLOSE button. Door should close.

If door did not reverse from obstruction, check entrapment

protection devices.

TEST THE ENTRAPMENT PROTECTION DEVICES

TEST REMOTE CONTROL

To avoid SERIOUS personal INJURY or DEATH:

• Disconnect electric power BEFORE performing ANY

adjustments or maintenance.

• ALL maintenance MUST be performed by a trained door

systems technician.

ATTENTION

AVERTISSEMENT AVERTISSEMENT

AVERTISSEMENT

WARNING

CAUTION

WARNING

WARNINGWARNING

PRECAUCIÓN ADVERTENCIA

ADVERTENCIAADVERTENCIA

The operators have provisions for manually operating the door in case of emergency or power failure. Refer to the appropriate

instructions for your model operator.

MODEL MT/BMT

EMERGENCY DISCONNECT

NO ECIT

Emergency

Disconnect

Door

Emergency

Release Handle

Emergency

Disconnect

Door Arm

Pull emergency release handle straight down. Emergency

disconnect will open.

Lift free end of door arm to trolley.

Pull emergency release handle to allow arm to engage roll

pin.

Let go of the emergency release handle. Emergency

disconnect will close.

TO DISCONNECT DOOR FROM OPERATOR

TO RECONNECT DOOR ARM TO TROLLEY

Emergency

Disconnect

Door Arm

To prevent possible SERIOUS INJURY or DEATH from a falling

door or arm:

• DO NOT stand under the door arm when pulling the emergency

release.

• If possible, use emergency release handle to disengage trolley

ONLY when door is CLOSED. Weak or broken springs or

unbalanced door could result in an open door falling rapidly

and/or unexpectedly.

• NEVER use emergency release handle unless doorway is clear

of persons and obstructions.

ATTENTION

AVERTISSEMENT AVERTISSEMENT

AVERTISSEMENT

WARNINGWARNING

CAUTION

WARNING

PRECAUCIÓN ADVERTENCIA

ADVERTENCIAADVERTENCIA

EMERGENCY DISCONNECT

MODEL MH

These operators are equipped with a manual hoist. An electrical

interlock will disable the electrical controls when the hoist is used.

Pull the disconnect chain (sash chain) to engage the hoist

mechanism. The disconnect chain may be locked in position

by slipping the end through the keyhole of the chain keeper

mounted on the wall.

Operate the door in the desired direction by pulling on one

side or the other of the continuous loop hoist chain.

The disconnect chain must be released from the chain keeper

before the door will operate again electrically.

ELECTRICAL INTERLOCK WITH HOIST FOR MODELS MH AND MHS

Chain Keeper

(with pad locking provisions)

MODEL MHS

The MHS operator includes both a ﬂoor level disconnect sash

chain to disconnect the door from the door operator that allows

manual push up operation and an additional sash chain to engage

the manual chain hoist that also electrically disables the operator

controls.

Refer to Model MH instructions for hoist operation.

Refer to Model MJ instructions for emergency operation.

When the manual chain hoist sash chain is engaged, electrical

operation will not function.

Keyhole Bracket

EMERGENCY DISCONNECT FOR MODELS MJ

MODELS MJ AND MGJ

This operator has a ﬂoor level disconnect chain to disconnect the

door from the door operator.

To disengage, pull the chain and secure in the disengaged

position by slipping the end through the keyhole bracket

mounted on the wall. Or if emergency egress device is used,

pull handle to disengage operator from door.

The door may now be pushed up or pulled down manually.

Release the disconnect chain or reset the emergency egress

device to operate the door again electrically.

ATTENTION

AVERTISSEMENT AVERTISSEMENT

AVERTISSEMENT

WARNING

CAUTION

WARNING

WARNINGWARNING

PRECAUCIÓN ADVERTENCIA

ADVERTENCIAADVERTENCIA

To prevent possible SERIOUS INJURY from a moving chain:

• DISCONNECT electric power to the operator BEFORE manually

operating your door.

• If possible, use emergency disconnect ONLY when door is

CLOSED. Weak or broken springs or unbalanced door could

result in an open door falling rapidly and/or unexpectedly.

• NEVER use emergency disconnect unless doorway is clear of

persons and obstructions.

To locate a dealer in your area visit us online at www.liftmaster.com.

Every 3 months or 5,000 cycles repeat all tests in the Testing section.

Call qualiﬁed service contractor for maintenance. To locate a dealer in your area visit us online at www.liftmaster.com.

The operator should be serviced at the following intervals:

• Every 3 months or 5,000 cycles

• Every 6 months or 10,000 cycles

• Every 12 months or 20,000 cycles

TROUBLESHOOTING

MAINTENANCE SCHEDULE

To avoid SERIOUS personal INJURY or DEATH from

electrocution, disconnect ALL electric power BEFORE performing

ANY maintenance.

ATTENTION

AVERTISSEMENT AVERTISSEMENT

AVERTISSEMENT

WARNING

CAUTION

WARNING

WARNINGWARNING

PRECAUCIÓN ADVERTENCIA

ADVERTENCIAADVERTENCIA

CONDITION POSSIBLE CAUSE FIX

OPERATOR WILL NOT

RESPOND TO ANY

COMMANDS

No power ➤Check circuit breaker.

Accessory failure ➤Verify photoelectric sensors are aligned.

Possible component failure ➤Contact your installing dealer.

OPERATOR MAKES

NOISE BUT DOOR

DOES NOT MOVE

Operator requires adjustment ➤Contact your installing dealer.

DOOR DRIFTS AFTER

OPERATOR STOPS

Operator or door requires

adjustment ➤Contact your installing dealer.

DOOR OPENS/CLOSES

TOO FAR Operator requires adjustment ➤Contact your installing dealer.

DOOR REVERSES

UNEXPECTEDLY

Entrapment protection device

activated

➤Verify photoelectric sensors are aligned. If photoelectric sensors are

aligned and operator still does not operate properly, contact your

installing dealer.

RADIO FUNCTIONALITY

NO RESPONSE Remote control is not

programmed ➤See PROGRAMMING REMOTE CONTROLS section.

Low battery ➤Replace battery.

REMOTE CANNOT BE

PROGRAMMED Low battery ➤Replace battery.

POOR RANGE Low battery in remote ➤Replace battery.

Possible radio interference ➤Contact your installing dealer.

OPERATOR NOTES

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Chamberlain Garagentoröffner Handbücher

Chamberlain

Chamberlain LiftMaster SECURITY+ 3585S Bedienungsanleitung

Chamberlain

Chamberlain 84505R Bedienungsanleitung

Chamberlain

Chamberlain LM60XX Bedienungsanleitung

Chamberlain

Chamberlain Icon 26 Bedienungsanleitung

Chamberlain

Chamberlain MotorLift ML750 Bedienungsanleitung

Chamberlain

Chamberlain C273 Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster Professional Security+ 3850 Bedienungsanleitung

Chamberlain

Chamberlain 4410E Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster PROFESSIONAL LM60 Series Bedienungsanleitung

Chamberlain

Chamberlain MyQ LM75EVK Bedienungsanleitung

Chamberlain

Chamberlain Power Drive PD505D Bedienungsanleitung

Chamberlain

Chamberlain Power Drive Security+ PD610 Bedienungsanleitung

Chamberlain

Chamberlain 75REV Bedienungsanleitung

Chamberlain

Chamberlain LM50EVFF Bedienungsanleitung

Chamberlain

Chamberlain Power Drive PD210M Bedienungsanleitung

Chamberlain

Chamberlain FS2 Security+ Bedienungsanleitung

Chamberlain

Chamberlain 1000SD Bedienungsanleitung

Chamberlain

Chamberlain T Bedienungsanleitung

Chamberlain

Chamberlain Security+ 2580 Bedienungsanleitung

Chamberlain

Chamberlain PD432DM 1/2 HP Owners Bedienungsanleitung

Chamberlain

Chamberlain 3280C 1/2 HP Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster Premium 8355 Bedienungsanleitung

Chamberlain

Chamberlain 3245C 1/3 HP Bedienungsanleitung

Chamberlain

Chamberlain Whisper Drive LW3500 Bedienungsanleitung

Beliebte Garagentoröffner Handbücher anderer Marken

Dorma

Dorma ES 90 Bedienungsanleitung

Garaga

Garaga SECURITY+ 3265GCM 1HP Bedienungsanleitung

Chase Doors

Chase Doors DuraShield Bedienungsanleitung

CSI

CSI Classic Bedienungsanleitung

HATO

HATO 120 Bedienungsanleitung

Richmond

Richmond GTR156 Bedienungsanleitung

Raynor

Raynor 1280RGD Bedienungsanleitung

CAME

CAME F4000 Series Bedienungsanleitung

B&D

B&D Controll-A-Door 5 Bedienungsanleitung

BFT

BFT PRV AA SL Bedienungsanleitung

Craftsman

Craftsman 139.53924 Bedienungsanleitung

Automatic Technology

Automatic Technology GDO-9V1 SecuraLift Bedienungsanleitung

Westfalia

Westfalia 19 36 07 Bedienungsanleitung

Cardin

Cardin BL Series Bedienungsanleitung

Craftsman

Craftsman 139.53997D Bedienungsanleitung

Bauer

Bauer CROSS18 Bedienungsanleitung

Wayne-Dalton

Wayne-Dalton 8124 Kurzanleitung

Craftsman

Craftsman 139.18867 Bedienungsanleitung