Chamberlain LiftMaster Professional 50-1950 Bedienungsanleitung

1. Assemble post bracket assembly by placing push-to-open bracket

between the two post brackets as shown. Insert 3/8" hex bolt through

middle hole. Fasten with lock washer, flat washer and nut (Figure 1).

2. With gate in open position (90˚ from closed position), clamp bracket

assembly to post using C clamp.

3. Rotate the push-to-open bracket or the entire post bracket assembly

to obtain desired dimensions (Figure 2).

4. Once dimensions are obtained, insert 5/16" hex bolt and fasten with

flat washer, lock washer, and nut to secure pivot point.

5. Mount operator to bracket assembly clamped to post by inserting

push-to-open bracket into slot on motor side of operator. Insert pin

and hairpin clips to secure (Figure 3).

6. Mount gate bracket to actuator side of operator with pin and hairpin

clips (Figure 3).

Figure 1

Figure 2

Figure 3

Push-to-Open Kit

Model 50-1950

3/8" Hex Bolt

Post Bracket

Push-to-Open Bracket

Post Bracket

3/8" Flat Washer

3/8" Lock Washer

3/8" Nut

Center of Gate Hinge

5/16" Hex Bolt

Special Post Pivot Bracket for

Push-to-Open Installation

7-3/4"

90°

Hex Bolt

Post Bracket

Push-to-Open Bracket

Lock Washer

Nut

Hairpin Clip

Gate Bracket

Flat Washer

7. With gate open and operator in retracted position, clamp bracket to

cross member, using C clamp. Adjust operator until assembly is

level. Tighten in place at this time (Figures 4 & 6).

NOTE: All four mounting holes must be used.

8. Once brackets are clamped in place, remove clevis pins and

washers to detach operator.

9. Mark reference points for bolt holes on fence posts and cross

member. Be sure to mark holes in the vertical center of post

bracket slots (Figure 5).

10. Remove brackets from gate post and cross member.

11. Drill 13/32" holes in marked locations for gate post and 11/32" for

gate bracket.

12. Secure post bracket assembly to gate post with 3/8"-16 x 6"

carriage bolts, flat washers, lock washers and nuts. Secure gate

bracket to cross member with 5/16" carriage bolts, flat washers,

lock washers and nuts.

13. Reattach operator to gate.

Figure 4

Figure 5

Figure 6

BATTERY REPLACEMENT

1. Disconnect power to operator.

2. Open the control box cover.

3. Remove all quick connect terminals in use to the control

board. Remember location of all wire connections for

reinstallation.

4. Remove control board and mounting plate.

5. Disconnect terminals leads to both batteries.

6. Replace both batteries and connect red wires to the positive

(+) terminals (red). Connect black wires to the negative (-)

terminals (black).

7. Install control board and mounting plate.

8. Reconnect all quick connect terminals to the control board.

9. Close cover of control box.

10. Reconnect power to operator.

To avoid SERIOUS personal INJURY or DEATH from

electrocution, DISCONNECT electrical power to operator

BEFORE proceeding.

To reduce the risk of FIRE or INJURY to persons use ONLY

Chamberlain part #K74-30762 for replacement batteries.

Gate in Open Position

LEVEL Horizontal Cross Member

Mark cross member through middle of

gate bracket slots and drill 11/32" holes

Mark fence post through middle of

bracket slots and drill 13/32" holes

Post Bracket Assembly

3/8"-16 x 6" Carriage Bolt

Operator MUST be level

Post Bracket

Assembly

C Clamp

Gate in OPEN Position Gate Bracket

C Clamp

Batteries

Control Board and

Mounting Plate

Fence Post

Andere Chamberlain Garagentoröffner Handbücher

Chamberlain

Chamberlain Power Drive Security+ PD612CS Bedienungsanleitung

Chamberlain

Chamberlain MYQ-G0303-SP Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster Elite Security+ 3800PLD Bedienungsanleitung

Chamberlain

Chamberlain C610C Bedienungsanleitung

Chamberlain

Chamberlain RJO20 Bedienungsanleitung

Chamberlain

Chamberlain Merlin MJ3800R Bedienungsanleitung

Chamberlain

Chamberlain merlin MT600 Bedienungsanleitung

Chamberlain

Chamberlain C400 Bedienungsanleitung

Chamberlain

Chamberlain 8808CB Bedienungsanleitung

Chamberlain

Chamberlain B1381C Bedienungsanleitung

Chamberlain

Chamberlain RJO101 Bedienungsanleitung

Chamberlain

Chamberlain AccessMaster Security+ M3100M-1/2HP Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster 355LM Security+ Bedienungsanleitung

Chamberlain

Chamberlain Elite 3585S 3/4 HP Bedienungsanleitung

Chamberlain

Chamberlain MT Bedienungsanleitung

Chamberlain

Chamberlain 8587WL Bedienungsanleitung

Chamberlain

Chamberlain HandyLift MyQ Bedienungsanleitung

Chamberlain

Chamberlain 8550W Bedienungsanleitung

Chamberlain

Chamberlain Series 5100 Bedienungsanleitung

Chamberlain

Chamberlain Whisper Drive WD912K Bedienungsanleitung

Chamberlain

Chamberlain 87504-267 Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster CSL24V Bedienungsanleitung

Chamberlain

Chamberlain K72-12508 Bedienungsanleitung

Chamberlain

Chamberlain ML510 Bedienungsanleitung

Beliebte Garagentoröffner Handbücher anderer Marken

Dorma

Dorma ES 90 Bedienungsanleitung

Garaga

Garaga SECURITY+ 3265GCM 1HP Bedienungsanleitung

Chase Doors

Chase Doors DuraShield Bedienungsanleitung

CSI

CSI Classic Bedienungsanleitung

HATO

HATO 120 Bedienungsanleitung

Richmond

Richmond GTR156 Bedienungsanleitung

Raynor

Raynor 1280RGD Bedienungsanleitung

CAME

CAME F4000 Series Bedienungsanleitung

B&D

B&D Controll-A-Door 5 Bedienungsanleitung

BFT

BFT PRV AA SL Bedienungsanleitung

Craftsman

Craftsman 139.53924 Bedienungsanleitung

Automatic Technology

Automatic Technology GDO-9V1 SecuraLift Bedienungsanleitung

Westfalia

Westfalia 19 36 07 Bedienungsanleitung

Cardin

Cardin BL Series Bedienungsanleitung

Craftsman

Craftsman 139.53997D Bedienungsanleitung

Bauer

Bauer CROSS18 Bedienungsanleitung

Wayne-Dalton

Wayne-Dalton 8124 Kurzanleitung

Craftsman

Craftsman 139.18867 Bedienungsanleitung