Chamberlain MyQ 821LM Bedienungsanleitung

iftMaster MyQ Smart Garage Hub - Troubleshooting Guide

This guide includes troubleshooting steps for situations that may occur with the iftMaster MyQ 821 M, 821 MB, or

MyQ-G0301.

LED indicators

When troubleshooting, take note of the various EDs on the iftMaster MyQ Smart Garage Hub.

LED color and state MyQ Smart Garage Hub status

Wi-Fi needs to be set up

No router communication

Wi-Fi setup active

Communicating with router

Programming mode

Wi-Fi connected

https://answers.alarm.com/ADC/Partner/Installation_and_Troubleshooting/Garage/ iftMaster_MyQ_Smart_Garage_Hub/ iftM…

Updated: Sat, 05 Sep 2020 16:31:10 GMT

The door sensor unable to program into the Wi-Fi Hub

• Press the Test button on the door sensor. The Yellow ED on the door sensor blinks. If the door sensor is

connected to the Wi-Fi Hub, the Wi-Fi Hub beeps once or twice to indicate the slot number the sensor is associated

with .

◦ If the Yellow ED on the door sensor does not blink, replace the 3 volt CR2450 ithium battery. For more

information, see Which type of battery does the MyQ Garage Door Tilt Sensor use?.

▪ If replacing the battery does not resolve the behavior, the door sensor may need to be replaced.

◦ If the Yellow ED blinks on the door sensor but continues to be unable to program into the Wi-Fi Hub, verify the

Wi-Fi Hub slot is available to enroll a door sensor.

▪ To clear the door sensor slot on the Wi-Fi Hub, press and hold the 1or 2button on the Wi-Fi Hub that is

connected to the door sensor until the Yellow ED turns off.

Note: If there is already a successful garage door sensor enrolled on the Wi-Fi Hub, verify that door

sensor's slot number by pressing its Test button before clearing the slots. Do not clear the successful door

sensor's slot number.

◦ If the ED on the door sensor is Red, it is incompatible with the 821 M due to its use of Bluetooth

communication and should only be programmed into the 821 MB or MyQ-G0301.

Important: iftMaster MyQ Smart Garage Hubs are only compatible with door sensors from their own

generation.

The Wi-Fi Hub is not connecting to the internet

• Verify there is sufficient Wi-Fi signal in the garage.

◦ The thickness and number of walls, doors or other barriers between the router and garage can affect signal

strength.

◦ The Wi-Fi Hub's average range is about 50-100 feet from the Wi-Fi router.

https://answers.alarm.com/ADC/Partner/Installation_and_Troubleshooting/Garage/ iftMaster_MyQ_Smart_Garage_Hub/ iftM…

Updated: Sat, 05 Sep 2020 16:31:10 GMT

◦ To test if the Wi-Fi Hub should work, take a smartphone into the garage and turn on Wi-Fi to verify Wi-Fi signal

is sufficient.

▪ MyQ® Garage performance is best if the smartphone shows two or more bars, however, the MyQ®

Garage should perform properly with one bar as well.

• Try connecting the Wi-Fi Hub to the internet from the same room as the router. Then move the Wi-Fi Hub back to

the garage to determine if the Wi-Fi Hub keeps a solid connection. The Green ED is solid to indicate it has an

internet connection.

◦ If a solid connection cannot be maintained, use a Wi-Fi range extender to boost signal strength in the garage.

Wi-Fi range extenders are readily available at most consumer electronics stores.

The option for non-MyQ Garage Door is not present

This occurs when the MyQ Smart Garage Hub has information in both non-MyQ door slots. Since the MyQ Smart

Garage Hub can only have up to two non-MyQ doors, the option to add a non-MyQ door is not present to prevent a new

attempt. If there is only one or no doors actually enrolled, delete the hub from the account, power cycle it, and re-

register the hub using its serial number to resolve the issue, as the door information is deleted when the hub is deleted

from the account.

Alternatively, clearing the slots and power cycling may resolve as well. Press and hold the [1] button to produce a solid

yellow ED. Continue to hold until the yellow ED turns off. The slot should now be clear. Repeat with [2] for the second

slot.

Android device is not connecting to the Wi-Fi Hub

• Some mobile devices like the Samsung Galaxy use a feature called auto-switching, which can cause the phone to

switch away from the home Wi-Fi network. This prevents it from being able to share network settings with the Wi-Fi

Hub. This feature can be turned off in advanced Wi-Fi options on the mobile device.

• If using a newer Android phone or an Android phone running 4.x (Ice Cream Sandwich of Jelly Bean), the phone

may be restricting access to the Wi-Fi signal. Verify the option for Check for internet service is not selected:

To verify the option using an Android phone:

1. Tap Settings.

2. Tap Connection.

3. Tap Wi-Fi.

4. Tap the Menu icon.

5. Tap Advanced.

6. Tap to uncheck Check for internet service.

7. Try connecting to the Wi-Fi Hub again.

When trying to pair with the Gateway using Bluetooth on iOS, it shows as being already

paired

It is required to "forget" the device before it can be paired again. With the blue light flashing on the gateway, pull up the

https://answers.alarm.com/ADC/Partner/Installation_and_Troubleshooting/Garage/ iftMaster_MyQ_Smart_Garage_Hub/ iftM…

Updated: Sat, 05 Sep 2020 16:31:10 GMT

iOS device's Bluetooth menu, and press the arrow next to MyQ-XYZ to pull up the advanced options. From this page,

choose to Forget the device. Once this has been done, it is possible to re-pair the Gateway with the device, and the Wi-

Fi settings are able to be shared again.

For more information, refer to Apple's Pair a third-party Bluetooth accessory with your iPhone, iPad, or iPod touch

support document.

The Wi-Fi Hub is not registering

Verify is the Wi-Fi Hub is associated with the iftmaster’s MyQ® Garage app. Each Wi-Fi Hub can only be associated

with one account. If the Wi-Fi Hub is connected to a iftMaster account, delete the Wi-Fi Hub from the iftMaster

account.

To remove the Wi-Fi Hub from a LiftMaster account:

1. og into the iftMaster MyQ website at https://www.myliftmaster.com/ ogin.aspx.

2. In the My Places & Devices section, click the Settings icon.

3. Click to select the desired Place (Wi-Fi Hub) to remove.

4. In Devices, click the trash can icon for the garage doors to remove from the iftMaster account.

5. In Places, click the trash can icon for the Wi-Fi Hub (gateway) to remove from the iftMaster account.

6. On the iftMaster dashboard, confirm that the gateway no longer appears in My Places & Devices.

7. Next, try re-registering the Wi-Fi Hub (gateway) on Alarm.com’s website.

All of the remotes are disconnecting from the garage door opener during enrollment

For many garage door openers, pressing and holding the program/learn button causes the opener to forget all the

devices that it is linked to. If all remotes are disconnected from the garage door opener, each remote needs to be re-

enrolled if the user wants to continue using it. Try to hold down the learn button for a shorter period of time to avoid this

in the future.

The 821LM is not operating the garage door opener

Verify the garage door opener is compatible and enrolled correctly. For information about compatibility, see the

iftMaster MyQ Smart Garage Hub Installation Guide - Compatible Openers. If the garage door is compatible and was

enrolled correctly, try to manually program the 821 M with the garage door.

Verify the garage door opener was enrolled correctly

If the garage door was manually opened or closed during the enrollment process, it may create a false positive and

prevent the opener from enrolling correctly. To troubleshoot this:

1. Send a remote command to the iftMaster MyQ Smart Garage Hub. If it beeps and flashes, this means the

command was received by the Smart Garage Hub.

2. Manually operate the garage door. If it reports its status in the Event History or on the Customer Website and app,

https://answers.alarm.com/ADC/Partner/Installation_and_Troubleshooting/Garage/ iftMaster_MyQ_Smart_Garage_Hub/ iftM…

Updated: Sat, 05 Sep 2020 16:31:10 GMT

the tilt sensor was correctly enrolled to the Smart Garage Hub.

3. Verify that when the garage door opener was enrolled to the Smart Garage Hub, the door moved on its own. If it

did not, the tilt sensor may have reported opening or closing unrelated to the Smart Garage Hub, causing the

Smart Garage Hub to set the incorrect frequency for the garage door. If this is the case, delete and re-add the

garage door to the Smart Garage Hub.

4. If the iftMaster MyQ Smart Garage Hub is still not operating the garage door opener, attempt to re-enroll it again,

but choose Unknown as the manufacturer.

Program the door sensor and garage door opener

Important: The following troubleshooting steps only apply to the 821 M. The 821 MB cannot be manually programmed

using these steps.

To program the door sensor to the 821LM:

1. Press and release the [1] button for door sensor 1 or [2] button for door sensor 2 on the 821 M. The yellow

ED turns solid to indicate it's active.

2. Press and release the Test button on the door sensor until the 821 M beeps and the light flashes.

◦ The yellow ED on the 821 M turns off.

◦ The hub beeps once if the door sensor was programmed into slot 1. The hub beeps twice if the door sensor

was programmed into slot 2. This helps identify which slot a door sensor is programmed to determine if the 1

or 2 button needs to be pressed for programming the garage door opener to the 821 M.

Note: Once a sensor is enrolled to a slot, press the test button on the tilt sensor at any time to identify which slot it

belongs to based on if it beeps once for slot 1 or twice for slot 2.

To program the garage door opener to the 821LM:

Important: Use the results from programming the door sensor to the 821 M to determine if the 1 or 2 button needs to

be pressed to program the garage door opener.

1. Press and release the Button (Settings), the Blue ED turns on solid.

2. Press and hold the Button again until the Green and Yellow EDs alternate blinking.

3. Press and release the Button again, the Yellow ED turns on solid.

4. Depending on which slot the garage door opener is being programmed into, press and release the [1] or [2]

button the number of times indicated in the following chart. Then the Yellow ED turns on solid.

https://answers.alarm.com/ADC/Partner/Installation_and_Troubleshooting/Garage/ iftMaster_MyQ_Smart_Garage_Hub/ iftM…

Updated: Sat, 05 Sep 2020 16:31:10 GMT

5. Press and release the Button. The Yellow and Green EDs blink.

6. Press and release the Learn button on the garage door opener.

7. Depending on which slot the garage door opener is being programmed into, press and release the [1] or [2]

button until the garage door opener clicks.

8. Depending on which slot the garage door opener is being programmed into, press and release the [1] or [2]

button again to activate the garage door opener.

◦ If the garage door opener does not activate, press and release the Button, then repeat steps 3-8.

9. Once the garage door activates, exit programming mode. To exit programming mode, press and hold the

Button until either the Blue ED blinks if Wi-Fi is not set up, or the Green ED turns on if Wi-Fi has already been

connected.

There are two LiftMaster Garage Door Openers with a hub, and both doors Open/Close

during the learning process or remote open/close commands

When sending commands to one of two iftMaster garage door openers with a hub, both doors may open or close if

both motors were left plugged in when learning two non-MyQ garage doors to one hub. Even after trying multiple factory

resets, it may be determined that the doors are using the same channel. Due to this, it is always important to only power

up the motor being enrolled one at that time.

This behavior is caused by the motor's remote control memory having both 821 M slots enrolled. As a result, the only

way to resolve this behavior is to erase the motor's remote control memory.

Caution: Clearing the garage door motor's remote control memory requires any remotes or codes to be re-enrolled after

completion. Check the motor's manual for steps on erasing and re-learning remotes. To verify the remote memory is

clear, test one of the customer's remotes. If the door still opens, it was not done successfully.

To resolve this behavior:

1. After the remote memory on the motor is clear, remove any existing door information from the Wi-Fi Hub.

◦ To clear the Wi-Fi Hub information, press and hold the [1] button on the 821 M for 10 seconds, and then do

the same for the [2] button. When pressing the button, a yellow light appears, and when it is off, the motor

https://answers.alarm.com/ADC/Partner/Installation_and_Troubleshooting/Garage/ iftMaster_MyQ_Smart_Garage_Hub/ iftM…

Updated: Sat, 05 Sep 2020 16:31:10 GMT

memory for that slot is clear. Release the button once the yellow ED turns off.

2. Power off the motor that is not being enrolled, and go through the enrollment process for one of the garage door

motors.

3. Once the first motor is enrolled, power off that motor and power on the other motor.

4. Go through the enrollment process for the garage door motor currently power on.

5. Once the second motor is enrolled, power on the first motor. Test remote commands to verify the garage motors

are functioning properly.

Door Sensor reports status Unknown or Malfunction

If the door sensor reports an Unknown or Malfunction status, try the following steps to restore communication.

Note: The default status of the door sensor when it's first enrolled is Unknown.

Locally open and close the garage door

Open and close the garage door using the opener's wall control. A manual update of the garage door's status can clear

the malfunction and restore communication.

Update the LiftMaster equipment list

Update the iftMaster equipment list to verify the correct status appears for the garage door. For more information about

requesting an update, see Request an updated iftMaster equipment list.

Verify the garage door opener is within communication range

The Wi-Fi hub should be installed on the ceiling in the garage where the garage door opener is located. The Hub should

also be within 30 feet open air of the door sensor that is installed on the garage door.

Test the door sensor battery

Test the door sensor to verify the device is receiving power by pressing the door sensor's Test button. The Yellow ED

on the door sensor blinks, and the Wi-Fi Hub beeps once or twice to indicate the slot number the sensor is associated

with.

• If the Yellow ED on the door sensor does not blink, replace the 3 volt CR2450 ithium battery. For more

information, see Which type of battery does the MyQ Garage Door Tilt Sensor use?.

◦ Once new battery is put in the door sensor, the garage door sensor should come back online. The garage door

may need to be opened/closed using the garage door opener's wall control for a manual update of the garage

door's status to restore communication.

◦ If Yellow ED still does not blink after replacing with good batteries, the door sensor may need to be replaced.

• If the Yellow ED blinks on the door sensor but the Wi-Fi Hub does not beep once or twice, the door sensor is not

connected to the Wi-Fi Hub. It is recommended to remove the door and relearn it into the Wi-Fi Hub.

https://answers.alarm.com/ADC/Partner/Installation_and_Troubleshooting/Garage/ iftMaster_MyQ_Smart_Garage_Hub/ iftM…

Updated: Sat, 05 Sep 2020 16:31:10 GMT

If the door sensor needs to be replaced or relearned:

1. Remove the garage door device using the Dealer Website or MobileTech app. The iftMaster Wi-Fi Hub does not

need to be removed. For more information about removing the garage door device, see How do I delete a

iftMaster MyQ device from a customer account?.

2. Clear the door sensor slot on the Wi-Fi Hub that the door sensor is enrolled into. To clear the door sensor slot,

press and hold the 1or 2button on the Wi-Fi Hub that is connected to the door sensor. The Yellow ED on the Wi-

Fi Hub turns on, and then turns off. Release the button when the Yellow ED turns off.

3. Enroll the garage door device to the Wi-Fi Hub. For more information about how to Add Devices with the Wi-Fi

Hub, see iftMaster MyQ Garage Universal Retrofit (821 M) - Installation Guide.

Door sensor reports Low Battery trouble condition

If the door sensor reports a Low Battery trouble condition on the Partner Portal or MobileTech app, try the following

steps.

Replace the battery

This trouble condition can be resolved by replacing the battery in the door sensor. The MyQ Garage Door Tilt Sensor

uses a 3 volt CR2450 ithium battery. For more information, see Which type of battery does the MyQ Garage Door Tilt

Sensor use?.

Send a Battery State command

If the battery has been replaced, but the trouble condition still is not resolved, try sending the Battery State command.

To send a Battery State command using the Partner Portal:

1. og into the Partner Portal.

2. Find the customer account.

3. Click Equipment.

4. Click LiftMaster.

5. In Device Commands, locate the row with the relevant door sensor and click Battery State.

https://answers.alarm.com/ADC/Partner/Installation_and_Troubleshooting/Garage/ iftMaster_MyQ_Smart_Garage_Hub/ iftM…

Updated: Sat, 05 Sep 2020 16:31:10 GMT

Andere Handbücher für myQ 821LM

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Chamberlain Garagentoröffner Handbücher

Chamberlain

Chamberlain D2101 Bedienungsanleitung

Chamberlain

Chamberlain MotorLift ML750 Bedienungsanleitung

Chamberlain

Chamberlain PD300DM 1/2 HP Bedienungsanleitung

Chamberlain

Chamberlain MyQ Bedienungsanleitung

Chamberlain

Chamberlain Power Drive Security+ PD612CDM Bedienungsanleitung

Chamberlain

Chamberlain HD220 Bedienungsanleitung

Chamberlain

Chamberlain Security+ 4620 Bedienungsanleitung

Chamberlain

Chamberlain WD850KEVG Bedienungsanleitung

Chamberlain

Chamberlain 3595LM 3/4 HP Bedienungsanleitung

Chamberlain

Chamberlain LM50EVFF Bedienungsanleitung

Chamberlain

Chamberlain HD950WF Bedienungsanleitung

Chamberlain

Chamberlain LJ8950W Bedienungsanleitung

Chamberlain

Chamberlain B980C Bedienungsanleitung

Chamberlain

Chamberlain T Bedienungsanleitung

Chamberlain

Chamberlain C203 Bedienungsanleitung

Chamberlain

Chamberlain 2110 1/3 HP Bedienungsanleitung

Chamberlain

Chamberlain 248739M Bedienungsanleitung

Chamberlain

Chamberlain CG40CD 1/2 HP Bedienungsanleitung

Chamberlain

Chamberlain Power Drive PD752 Bedienungsanleitung

Chamberlain

Chamberlain GH Bedienungsanleitung

Chamberlain

Chamberlain Series OCG Bedienungsanleitung

Chamberlain

Chamberlain POWER DRIVE 7520D 1/2 HP Bedienungsanleitung

Chamberlain

Chamberlain Security+ 3290 Bedienungsanleitung

Chamberlain

Chamberlain Security+ 1000SDC-R Bedienungsanleitung

Beliebte Garagentoröffner Handbücher anderer Marken

Dorma

Dorma ES 90 Bedienungsanleitung

Garaga

Garaga SECURITY+ 3265GCM 1HP Bedienungsanleitung

Chase Doors

Chase Doors DuraShield Bedienungsanleitung

CSI

CSI Classic Bedienungsanleitung

HATO

HATO 120 Bedienungsanleitung

Richmond

Richmond GTR156 Bedienungsanleitung

Raynor

Raynor 1280RGD Bedienungsanleitung

CAME

CAME F4000 Series Bedienungsanleitung

B&D

B&D Controll-A-Door 5 Bedienungsanleitung

BFT

BFT PRV AA SL Bedienungsanleitung

Craftsman

Craftsman 139.53924 Bedienungsanleitung

Automatic Technology

Automatic Technology GDO-9V1 SecuraLift Bedienungsanleitung

Westfalia

Westfalia 19 36 07 Bedienungsanleitung

Cardin

Cardin BL Series Bedienungsanleitung

Craftsman

Craftsman 139.53997D Bedienungsanleitung

Bauer

Bauer CROSS18 Bedienungsanleitung

Wayne-Dalton

Wayne-Dalton 8124 Kurzanleitung

Craftsman

Craftsman 139.18867 Bedienungsanleitung

Chamberlain myQ 821LM Bedienungsanleitung

Beliebte Garagentoröffner Handbücher anderer Marken