Chamberlain EL1SS Montageanleitung

Installation and

Programming Manual

EL1SS

Telephone Entry System

For more information,

please visit www.devancocanada.com

or call toll free at 855-931-3334

INTRODUCTION PROGRAMMINGTESTINGINSTALLATION

INTRODUCTION ..............................2-3

Cable Requirements........................................................... 2

Dimensions........................................................................ 2

Carton Inventory ................................................................ 3

Description of the Processor Board................................... 3

INSTALLATION ............................. 4-12

Mount the Unit................................................................... 4

Overview of Telco Wiring................................................... 4

Typical Telco Overview with the Unit................................. 5

Wiring the Unit With a Telco Line...................................... 6

Wiring the Unit Without a Telco Line................................. 6

Wiring a Gate Operator (Normally Open)........................... 7

Wiring an Auto-Call Sensor ............................................... 7

Wiring a Gate Operator (Normally Open)

and a Door Strike Lock (Normally Open)........................... 8

Wiring a Gate Operator (Normally Open)

and a Maglock (Normally Closed)......................................9

Wiring a Door Strike Lock (Normally Open) .................... 10

Wiring a Maglock (Normally Closed)............................... 10

Earth Ground Rod............................................................11

Power Wiring................................................................... 11

Plug the Transformer into the Outlet ............................... 12

Close the Unit .................................................................. 12

Set the Unit Master Code................................................. 12

TESTING........................................13

Test the Gate/Door Relays ............................................... 13

Test the Telephone Connections......................................13

PROGRAMMING...........................14-20

General Instruction .......................................................... 14

Code Setup ......................................................................15

Code Operation ................................................................ 15

Telephone Programming ................................................. 16

Telephone Commands ..................................................... 17

Quick Reference..........................................................18-20

REPAIR PARTS ................................21

EL1SS MASTER CODE........................21

WARRANTY ....................................22

INTRODUCTION PROGRAMMINGTESTINGINSTALLATION

CABLE REQUIREMENTS

DIMENSIONS

Power Supply: 12 Vac 20 VA or 16 Vdc 2.5A

Outdoor installations require shielded cable. Non-shielded cable can be used for indoor installations ONLY.

PROCESSOR BOARD WIRE TYPE RECOMMENDATIONS

From the power transformer at 120 Vac outlet 2 - Conductor Cable Shielded Only - See Power Wire Table Below

From the door strike, maglock or gate operator 2 - Conductor Cable See device specifications for wire size

From the strike power supply (if needed) 2 - Conductor Cable See device specifications for wire size

From the Earth ground to processor board 12 AWG copper wire,

PVC insulated

12 AWG copper wire,

uninsulated

Belden #9912

Belden #8011

Residence and Telco phone lines 24 AWG twisted

pair telephone wire

Shielded - Belden #9502

From the processor board 24 AWG twisted

pair telephone wire

Shielded - Belden #9502

Between processor boards on

multiple entrance installation

24 AWG twisted

pair telephone wire

Shielded - Belden #9502

POWER WIRE TABLE

NOTE: LiftMaster is not responsible for conflicts between the information listed in the above table and the requirements of local building

codes. The information is for suggested use only. Check local building codes before installation.

DISTANCE AC POWER WIRE SIZE

Under 30 feet 18 AWG

30 - 75 feet 18 AWG

75 - 150 feet 18 AWG

150 - 250 feet 16 AWG

250 - 500 feet 12 AWG

123

456

7 8 9

10.05"

6.14"

5.265"

2.8"

4.243" 3" .312"

5.025"

1.125"

INTRODUCTION PROGRAMMINGTESTINGINSTALLATION

CARTON INVENTORY

Unit (1)

Key (1)

12 Vac 20 VA or 16 Vdc 2.5A Plug-In UL Listed Power Transformer (1)

Bypass Board (1)

Manual (1)

11 2

1Autocall Input: Connector for accessory device to trigger

home dialing.

2Power Connector: 12 Volt AC power input. 8Ground Wire: Wire must be connected to positive earth

ground. See Earth Ground Rod.

7Tamper Switch

5Phone Output: Telephone return connection to home or

office phones.

6Line Input: Telephone input connection from “Telco” service

provider.

4Relay 1 Output: Form “C” primary control relay.

12 Relay 1 (Primary) Output Status LED

13 Relay 2 (Secondary) Output Status LED

10 Voice Data Send Status LED

9Status LED

11 Power Status LED

DESCRIPTION OF THE PROCESSOR BOARD

3Relay 2 Output: Form “C” secondary control relay.

NC NC

NO NO

COM COM

INTRODUCTION PROGRAMMINGTESTINGINSTALLATION

1. Choose the mounting location for the unit.

2. Unlock faceplate and open.

3. Mark holes and pre-drill holes.

4. Mount to a solid surface or post (hardware not provided).

MOUNT THE UNIT

12:00

Dec. 31

REDIAL

TALK

OFF

FLASH

123

456

789

&’)

ABC

GHI JKL MON

PQRS TUV

WXYZ

OPER

DEF

Home Phone

Ring

(Not Provided)

Telco Entrance Box

Demarcation Point

Tip

Alarm System

Position

NOTES:

• The voltmeter measurement between the Tip and Ring should

be between 48 and 53 Vdc.

• Never run data wires and high voltage wires in the same

conduit. The high voltage wires may interfere with the data

wires and cause the system to malfunction.

• Reversed polarity will not damage the unit, however, some

telephones will not function properly.

Many phone companies have updated their color standards due to

the use of Cat 5 cable for most phone line installs, and keep

residential and business installs in line with each other. In the new

standard, there is no green, red, black or yellow wires, they have

been replaced by white/blue, blue/white, white/orange, and

orange/white. If the wire is primarily orange with white stripes

then that color is orange/white. Refer to the table below. The NID

labels will most likely have the old coloring scheme on them, and

most telephone wiring components you can purchase will still

reflect the original colors.

Accessories: Optional method to mount.

LiftMaster Gooseneck Pedestal Post Models

PED42 or PED64

Function Old Color Standard New Color Standard

Tip 1 Green White/Blue

Ring 1 Red Blue/White

Tip 2 Black White/Orange

Ring 2 Yellow Orange/White

OVERVIEW OF TELCO WIRING

• Wire connectors can be

removed to simplify wiring.

• DO NOT overload wire

connectors. Use ONLY one

wire per hole.

Typical Telco Overview

Wall Mount Pedestal Mount

INTRODUCTION PROGRAMMINGTESTINGINSTALLATION

12:00

Dec. 31

REDIAL

TALK

OFF

FLASH

123

456

789

&’)

ABC

GHI JKL MON

PQRS TUV

WXYZ

OPER

DEF

PHONE LINE

TIP

RING

TIP

RING

Telco Entrance Box

Demarcation Point

Bypass Board

Alarm System

Position (Not Provided)

Telco

Phone lines with DSL service. In order for the EL1SS to function normally a DSL filter is required to separate the DSL (digital) signal

from the telephone service (POTS).

1. Install the splitter between the demarcation box and the EL1SS.

2. Route the DSL/Phone wires from the demarcation box to the splitter’s input terminal.

3. Run a copper, twisted pair from the splitter’s phone output to the EL1SS.

4. Run the data wires from the splitter to the resident’s computer network.

5. Run the residence phone wires from the EL1SS to the residence phone(s).

TYPICAL TELCO OVERVIEW WITH THE UNIT

CONNECTING THE BYPASS BOARD

The bypass board allows the EL1SS unit to be disconnected

without interrupting normal telephone operation. If the unit is

used in conjunction with an alarm system, you must connect

the telephone line to the alarm system ﬁrst or the unit will not

operate properly.

NOTES:

• When a unit is in use, the bypass switch must be set to

operate.

• When a unit is disconnected, the bypass switch must be

set to bypass.

• If the unit will be connected with an alarm system, you

must connect the telephone line to the alarm system

first in the series from the Telco box. If the units are not

connected in this order, they will not operate properly.

Disconnect power at the fuse box BEFORE proceeding. The unit

MUST be properly grounded and connected in accordance with

national and local electrical codes. NOTE: The unit should be on

a separate fused line of adequate capacity.

• A static discharge can damage circuit boards

• NEVER run telco wires and high voltage wires in the same

conduit. The high voltage may interfere with the telco wires,

possibly causing the system to malfunction.

INTRODUCTION PROGRAMMINGTESTINGINSTALLATION

WIRING THE UNIT WITH A TELCO LINE

WIRING THE UNIT WITHOUT A TELCO LINE

12:00

Dec. 31

REDIAL

TALK

OFF

FLASH

123

456

789

&’)

ABC

GHI JKL MON

PQRS TUV

WXYZ

OPER

DEF

12:00

Dec. 31

REDIAL

TALK

OFF

FLASH

123

456

789

&’)

ABC

GHI JKL MON

PQRS TUV

WXYZ

OPER

DEF

12:00

Dec. 31

REDIAL

TALK

OFF

FLASH

123

456

789

&’)

ABC

GHI JKL MON

PQRS TUV

WXYZ

OPER

DEF

12:00

Dec. 31

REDIAL

TALK

OFF

FLASH

123

456

789

&’)

ABC

GHI JKL MON

PQRS TUV

WXYZ

OPER

DEF

PHONE LINE

TIP

RING

TIP

RING

TipTip Tip

Telco

Entrance Box

Demarcation

Point

Ring RingRing

Ringer Equivalence Number (REN) = 4

The unit can be a stand alone system that allows communication between the unit and the resident’s phones.

12:00

Dec. 31

REDIAL

TALK

OFF

FLASH

123

456

789

&’)

ABC

GHI JKL MON

PQRS TUV

WXYZ

OPER

DEF

12:00

Dec. 31

REDIAL

TALK

OFF

FLASH

123

456

789

&’)

ABC

GHI JKL MON

PQRS TUV

WXYZ

OPER

DEF

12:00

Dec. 31

REDIAL

TALK

OFF

FLASH

123

456

789

&’)

ABC

GHI JKL MON

PQRS TUV

WXYZ

OPER

DEF

12:00

Dec. 31

REDIAL

TALK

OFF

FLASH

123

456

789

&’)

ABC

GHI JKL MON

PQRS TUV

WXYZ

OPER

DEF

PHONE LINE

TIP

RING

TIP

RING

Telco Entrance Box

Demarcation Point

Telco

Bypass Board

Ring Ring Ring

Tip Tip Tip

Ringer Equivalence Number (REN) = 4

Never run data wires and high voltage wires in the same conduit. The high voltage wires may interfere with the data wires

and cause the system to malfunction.

INTRODUCTION PROGRAMMINGTESTINGINSTALLATION

Loop Sensor

(Normally Open)

Loop

Detector

WIRING A GATE OPERATOR (NORMALLY OPEN)

Primary Gate

Operator

(Strike Open Input)

(Normally Open)

COM

(Common)

The gate operator can be connected to Relay 1 or Relay 2. See the Programming section for information about configuring

Relays 1 and 2.

The Auto-Call feature will enable the unit to contact the resident

when a driveway sensor (or any device that provides a contact

closure) is activated.

WIRING AN AUTO-CALL SENSOR

• Wire connectors can be removed to simplify

wiring.

• DO NOT overload wire connectors. Use

ONLY one wire per hole.

INTRODUCTION PROGRAMMINGTESTINGINSTALLATION

Primary Gate Operator

(Strike Open Input)

COM

(Common)

(Normally Open)

NOTE: For DC power

install a 1N4001 diode

or equivalent.

NOTE: For AC power install a

Siemens S10K30 MOV

(Metal Oxide Varistor) or equivalent.

AC or DC

Power

COM (Common)

NO (Normally Open)

NOTE: Do not use

the unit’s power supply

for the door strike.

Door Strike

WIRING A GATE OPERATOR

(NORMALLY OPEN) & A DOOR

STRIKE LOCK (NORMALLY OPEN)

The door strike can be connected to Relay 1 or Relay 2. See

the Programming section for information about configuring

Relays 1 and 2.

• Wire connectors can be

removed to simplify wiring.

• DO NOT overload wire

connectors. Use ONLY one

wire per hole.

INTRODUCTION PROGRAMMINGTESTINGINSTALLATION

WIRING A GATE OPERATOR (NORMALLY OPEN) & A MAGLOCK

(NORMALLY CLOSED)

The maglock can be connected to Relay 1 or Relay 2. See the

Programming section for information about configuring Relays 1

and 2.

NOTE: Install a 1N4001

diode or equivalent.

NOTE: Do not use

the unit’s power

supply for the maglock.

DC Power

Primary Gate Operator

(Strike Open Input)

COM

(Common)

(Normally Open)

COM (Common)

NC (Normally Closed)

Maglock

Andere Handbücher für EL1SS

Inhaltsverzeichnis

Andere Chamberlain Gegensprechanlage Handbücher

Chamberlain

Chamberlain WIRELESS PORTABLE INDOOR/OUTDOOR INTERCOM... Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster ELITE EL25 Bedienungsanleitung

Chamberlain

Chamberlain LSIAC Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster 833-1LM Bedienungsanleitung

Chamberlain

Chamberlain MyQ Business CAPXL Bedienungsanleitung

Chamberlain

Chamberlain RFDI Bedienungsanleitung

Chamberlain

Chamberlain WIRELESS GATE ACCESS RGAIPI Bedienungsanleitung

Chamberlain

Chamberlain EL1SS Benutzerhandbuch

Chamberlain

Chamberlain ELITE EL2000LG Betriebsanleitung

Chamberlain

Chamberlain APEX Access Device Bedienungsanleitung

Chamberlain

Chamberlain Elite EL25N Bedienungsanleitung

Chamberlain

Chamberlain RFDIC Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster ELITE EL2000 Betriebsanleitung

Chamberlain

Chamberlain Smart Video Intercom M Bedienungsanleitung

Chamberlain

Chamberlain NLS1 Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster ELITE EL25 Bedienungsanleitung

Chamberlain

Chamberlain OPI Bedienungsanleitung

Chamberlain

Chamberlain WIRELESS PORTABLE INDOOR/OUTDOOR INTERCOM... Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster ELITE EL25 Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster Professional RIFM1LM Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster FDI Bedienungsanleitung

Chamberlain

Chamberlain MyQ Business CAPXL Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster 831-2LM Bedienungsanleitung

Chamberlain

Chamberlain RIFMS2 Bedienungsanleitung

Beliebte Gegensprechanlage Handbücher anderer Marken

Bticino

Bticino LINEA 3000 Bedienungsanleitung

MSI

MSI MSI-140 Bedienungsanleitung

golmar

golmar Stadio Plus Bedienungsanleitung

CyberData

CyberData 011211 series Handbuch

Vidos

Vidos duo M1021 Bedienungsanleitung

Vimar

Vimar ELVOX 7539/E Bedienungsanleitung

SSS Siedle

SSS Siedle BTSV 850-03 Bedienungsanleitung

Dahua

Dahua VTO Series Bedienungsanleitung

Elvox

Elvox 5651 Bedienungsanleitung

Videx

Videx VIDEOKIT Series Bedienungsanleitung

Rocom

Rocom Doortello Business FW T2.05W2.04 Bedienungsanleitung

Viking

Viking E-35-EWP Bedienungsanleitung

Safeguard Supply

Safeguard Supply LRA-EX1000 Bedienungsanleitung

SSS Siedle

SSS Siedle BFCV 850 Series Bedienungsanleitung

GRD

GRD MAX V2 Bedienungsanleitung

Alecto

Alecto ADI-250 Bedienungsanleitung

Aiphone

Aiphone IE-8MD Bedienungsanleitung

Perel

Perel EDB4 Bedienungsanleitung