Chamberlain 480LMC Bedienungsanleitung

To avoid possible SERIOUS INJURY to fingers from moving

garage door opener:

• Be sure power is not connected to the garage door opener

BEFORE installing the 480LM mounting kit.

• ALWAYS keep hand clear of chain and sprocket while

operating opener.

• Securely attach chain cover BEFORE operating.

Figure 2

Figure 1

Models 480LM & 480LMC

Alternate Mounting Kit

INSTALLATION

1. Disassemble kit and remove foam pad (attached to

sprocket hub). Discard foam pad.

2. Attach the T-bracket to the motor unit using the

self-threading screws (Figure 1).

NOTE: The T-bracket will be above the existing mounting

bracket.

3. Attach sprocket with larger bore (1-1/4") to the motor

shaft of the opener. Position the sprocket so that the

screws are facing up and are accessible when

attached to the torsion bar (Figure 2).

4. Tighten both sides of the sprocket screws equally to

secure the sprocket to the motor unit (12-14 ft./lbs.

of torque). Securely tighten set screw.

CARTON INVENTORY

1T-bracket

21-1/4" Sprocket with Collar and Screws

31" Sprocket with Collar and Screws

4Chain

5Cover Assembly

NOT SHOWN

Hardware: 1/2" Screw (1),

#10 Self-Threading Screw (2),

and 1-1/2" Hex Head Screw (2)

Instructions

(provided with opener)

Figure 5

Figure 6 Figure 7

INSTALLATION

5. Attach sprocket with the smaller bore (1") to the

torsion bar making sure that the screws are on the

side closest to the garage door (Figure 3).

NOTE: Do not tighten sprocket at this time.

6. Place the chain on the sprocket located on the

torsion bar (Figure 4).

7. Attach the sprocket located on the motor unit shaft to

the chain. Secure the motor unit to the wall using the

hex head screws (Figure 5).

NOTE: Ensure that the chain is perpendicular to the bar

and not too tight.

8. Tighten both screws of the sprocket on the torsion

bar equally to secure the sprocket to the bar

(12-14 ft./lbs. of torque). Securely tighten set screw.

You may need to rotate the chain to make the

screws accessible.

9. One side of the chain cover will have an indentation

that will fit into the middle of the motor unit sprocket.

This side should be put on first (Figure 6).

10. Position the remaining cover over the other side so

that it encloses the chain and sprocket assembly.

The covers will snap into place. Secure them by

screwing them together using the 1/2" screw

(Figure 7).

11. Rotate chain to ensure smooth travel. Adjust, if

necessary.

12. Refer to Installation Step 2 of the owner’s manual for

further instructions.

Figure 4

Figure 3

Dieses Handbuch passt für folgende Modelle

Andere Chamberlain Rack & Stand Handbücher

Chamberlain

Chamberlain Liftmaster Elite Series Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster CSW200UL Series Bedienungsanleitung

Chamberlain

Chamberlain MRIN Bedienungsanleitung

Chamberlain

Chamberlain FOHMODDC Bedienungsanleitung

Chamberlain

Chamberlain 195LM Bedienungsanleitung

Chamberlain

Chamberlain CAPXSGNB Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung