Chamberlain 976LM Security+ Bedienungsanleitung

To comply with FCC/IC rules, adjustment or modification of receiver and/or

transmitter is prohibited, except for changing the code setting and replacing the

transmitter battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.

Installation

Choose a convenient

location for installation.

It should be at eye

level, reachable by the

shortest person who

will use it, and within

sight of the door.

For a one-piece door,

use the optional

location shown in the

illustration (on the edge

of the door jamb) to avoid injury as the door

swings up and out.

Test the reception of the Keyless

Entry by operating your opener

from the selected location.

Change the location if necessary.

Remove the battery compartment

cover to access the bottom

mounting hole:

• Insert a small phillips screw driver

into the small hole at the bottom of

the cover and gently pull outward to

loosen.

• Slide the cover down to remove.

Center the keypad at eye level against the selected

location. Mark 4-1/4" up the centerline from the bottom and

drill a 1/8" pilot hole. Install top mounting screw, allowing

1/8" to protrude above surface. Position keypad on screw

head and adjust for snug fit.

With cover open so bottom mounting hole is visible, use a

punch to mark hole. Remove keypad and drill 1/8" pilot

hole. Replace keypad and complete installation with

bottom screw, using care to avoid cracking plastic housing.

Do not overtighten.

To replace the battery cover, insert the lip at the top and

snap in place.

Side two contains instructions for changing the personal

entry password and setting a temporary password.

Door Jamb Edge

(Optional Location

for 1-Piece Door)

Keypad

Door Jamb Face

SECTIONAL DOOR ONLY

KEYPAD MUST BE INSTALLED

WITHIN SIGHT OF THE DOOR

Exterior Front Wall

1-Piece or

Sectional Door

Typical

Sectional Door

Installation

Setting the Personal Entry Password

We recommend that you program your personal

password now, before you install the Keyless Entry.

Then you can test the reception at the mounting

location before you proceed further.

1. Choose a 4-digit personal entry password using the

numbers from 0 to 9 (a number can be used more than

once, for example, 4,0, 4,1).

2. Press the four buttons for the

password, then press and

hold

the Enter button. The

indicator light on the door

opener panel will blink.

3. Press and release the “Smart”

(learn) button on the door

opener panel. After the

opener lights blink, release

the Enter button.

Test by pressing the the password, then press Enter. The

door should begin to move.

You may also program the Keyless Entry from a

multifunction door control, as follows:

With the door closed,

enter the four digit password

desired, then press and hold Enter.

2. Press and hold the light button on the door control.

3. Press and hold the door control push bar.

4. After the opener lights blink, release all buttons.

SECURITY✚

Garage Door Opener

"Smart" (learn)

Button Indicator Light

KG KG

123

Children operating or playing with a garage door

opener can injure themselves or others.

The

garage door could close and cause serious injury

or death.

Do not allow children to operate the wall

push button(s) or remote control(s).

A moving garage door could injure or kill someone

under it.

Activate the opener only when you can see

the door clearly, it is free of obstructions, and is

properly adjusted.

WARNING

Model 976LM, 976LMC Security✚

Wireless Keyless Entry

Features

For use with any SECURITY✚

compatible garage door opener

receiver.

Personalized Password: Up to

10,000 possible combinations. Password

can be easily changed if desired.

Temporary password: Can be added for visitors

or service persons. This temporary password can be

limited to a programmable number of hours or a

programmable number of entries.

Rolling Code: While your password remains constant until

you change it, the code between the Keyless Entry and the

receiver changes with each use, randomly accessing over

100 billion new codes.

Operation: Opener activates when 4-digit password and

Enter button is pressed.

If wrong numbers are accidentally pressed, correction can be

made immediately. The Enter button will transmit only the last

four digits.

The Keypad will blink for 15 seconds after the password is

transmitted. During that time the Enter button can be used to

stop or reverse the door travel.

Battery

Bottom

mounting hole

Battery

Cover

Changing the Personal Entry Password

Press the four buttons for the present password, then

press and hold the # button.

The opener light will blink twice. Release the # button.

Press the new 4-digit password you have chosen, then

press Enter.

The opener light will blink once when the password has

been learned.

Test by pressing the new password, then press Enter.

The door should move.

Setting a Temporary Password

In addition to the personal entry password which works at

all times, a 4-digit temporary password can be added for

the convenience of visitors or service persons. This

allows authorized persons a way to gain temporary

access. After a programmed number of hours or number

of accesses, this temporary entry password expires and

will no longer open the door. The temporary password

can be used to

the door even after it has expired.

To set a temporary entry password:

1. Press the four buttons for your personal entry password

(not the last temporary password), then press and hold

the ✽button.

The opener light will blink three times. Release the

button.

2. Press the temporary 4-digit entry password you have

chosen, then press Enter.

The opener light will blink four times.

3. To set the number of

hours

this temporary password

will work, press the number of hours (up to 255), then

press ✽.

3. To set the number of

times

this temporary password

will work, press the number of times (up to 255), then

press #.

The opener light will blink once when the temporary

password has been learned.

Test by pressing the four buttons for the temporary

password, then press Enter. The door should move. If the

temporary password was set to a certain number of

openings, remember that the test has used up one

opening.

To clear the temporary password, repeat steps 1-3,

setting the number of hours or times to 0 in Step 3.

Battery

The 9 volt battery should produce power for at least one

year. Replace when keypad illumination becomes dim.

FOR SERVICE DIAL OUR TOLL FREE NUMBER: 1-800-528-2817

IN CANADA, DIAL 1-800-654-4736

Andere Handbücher für 976LM Security+

Dieses Handbuch passt für folgende Modelle

Andere Chamberlain Fernstartsystem Handbücher

Chamberlain

Chamberlain LiftMaster Securty+ 976LM Bedienungsanleitung

Chamberlain

Chamberlain Series 740 Bedienungsanleitung

Chamberlain

Chamberlain 942FP-10 Bedienungsanleitung

Chamberlain

Chamberlain 942FPC-10 Bedienungsanleitung

Chamberlain

Chamberlain 940C Security+ Bedienungsanleitung

Chamberlain

Chamberlain 940EV Bedienungsanleitung

Chamberlain

Chamberlain 940CD-01 Bedienungsanleitung

Chamberlain

Chamberlain 878MAX Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster 466LM Bedienungsanleitung

Chamberlain

Chamberlain 940EV Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster TAC1 Montageanleitung

Chamberlain

Chamberlain LiftMaster 379LM-10 Bedienungsanleitung

Chamberlain

Chamberlain Security+ 377LG Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster Professional 387LM Bedienungsanleitung

Chamberlain

Chamberlain SECURITY+ 940-315CB Bedienungsanleitung

Chamberlain

Chamberlain POWER DRIVE Whisper Drive 940CB Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster Security+ 377LM Bedienungsanleitung

Chamberlain

Chamberlain 942FPC Bedienungsanleitung

Chamberlain

Chamberlain Clicker KLIK2U Bedienungsanleitung

Chamberlain

Chamberlain 40 Bedienungsanleitung

Chamberlain

Chamberlain 727E Series Bedienungsanleitung

Chamberlain

Chamberlain 66 Bedienungsanleitung

Chamberlain

Chamberlain Security+ 940CB Bedienungsanleitung

Chamberlain

Chamberlain 877MAX Bedienungsanleitung

Beliebte Fernstartsystem Handbücher anderer Marken

AstroStart

AstroStart 803U Bedienungsanleitung

Durite

Durite 0-649-20 Handbuch

EINHELL

EINHELL BT-PS 1000 Handbuch

Linear

Linear ACCESS AK-21 Technische Daten

Soundstream

Soundstream TARANTULA RS.2 Bedienungsanleitung

Jaycar Electronics

Jaycar Electronics MB3752 Bedienungsanleitung

Ultra Start

Ultra Start 72 Series Bedienungsanleitung

ADS

ADS FLASHLOGIC FLRSVW1 Bedienungsanleitung

Selecta

Selecta JS012 Bedienungsanleitung

Black Widow Security

Black Widow Security BW RAS 400 Bedienungsanleitung

Vector

Vector Power City DK080706 Beilage

Code Alarm

Code Alarm CA-535 Bedienungsanleitung

Ozito

Ozito OJS-800 Bedienungsanleitung

Profi-Partner

Profi-Partner 46387 Bedienungsanleitung

EZ STARTER

EZ STARTER EZ-45 Bedienungsanleitung

Viper

Viper 4204 Bedienungsanleitung

Essex Electronics

Essex Electronics KE-1701 Bedienungsanleitung

EINHELL

EINHELL EGS 3600 Handbuch