Champion SVPRO Series Technisches Handbuch
Champion Tool Storage
3070 Lower Mill Dr.
Hood River Oregon 97031
W: www.championbuilt.com
E-mail: [email protected]
PROPER USE AND INSTALLATION FOR CHAMPION SVPRO SERIES
QUESTIONS
Phone: 866-391-4200
8 AM - 5PM, PST, Monday-Friday
The following instructions will provide you with a guide for installation and usage
for the SVPRO Series cabinets. If at any time you need guidance or help, please
do not hesitate to call us. Thanks again for choosing Champion Tool Storage.
THIS DOCUMENT IS CONFIDENTIAL AND PROPRIETARY PART NO. 1000629
THIS DOCUMENT IS CONFIDENTIAL AND PROPRIETARY PART NO. 1000629
2
Table Of Contants
Before You Begin 3
Installation Site Prep 4
Installation 7
Proper Use 11
Lock Use 12
Warranty 12
Proper Care / Safety 12
Check your inventory to be sure you received your entire order. If there are
any missing or damaged parts, contact Champion Customer Service at 541-
386-7700
Only use the provided hardware during assembly.
Read and understand the entire installation instructions prior to beginning
the install.
1.
2.
3.
THIS DOCUMENT IS CONFIDENTIAL AND PROPRIETARY PART NO. 1000629
Before You Begin
Tools Required
Hammer Socket Wrench
Punch ToolBox Wrench 7/16
3
9/16 Deep Socket 7/16 Deep Socket
6" Extension Wirecutters
THIS DOCUMENT IS CONFIDENTIAL AND PROPRIETARY PART NO. 1000629
Site Prep
1. A level concrete pad is recommended that is 6" larger in width and 6" larger in depth
of the total number of cabinets being installed. See below for recommended pad size
for one, two, and three units. A single unit template is available for purchase if
needed, part #4003551 Locker Base Drill Template.
Install (4) 3/8" X 3-3/4" Concrete Wedge Anchors(not included) per unit into the drilled
holes on the concrete pad.
Remove the nut and washers on the Concrete Wedge Anchors before installing the
SVPRO units.
Before installing the units, make sure your site is ready.
Single Locker Pad
4
THIS DOCUMENT IS CONFIDENTIAL AND PROPRIETARY PART NO. 1000629
Site Prep
Double Locker Pad
5
THIS DOCUMENT IS CONFIDENTIAL AND PROPRIETARY PART NO. 1000629
Site Prep
Triple Locker Pad
6
Installation
THIS DOCUMENT IS CONFIDENTIAL AND PROPRIETARY
1. Use a forklift or pallet jack to move the following Models
into place, SVP2, SVP5, and SVP8.
Remove all packaging.
Set the unit on the pad and align the holes over the studs in
the Concrete Pad.
See Step 5 for installation instructions for the SVP3. Note,
All locker doors must be locked while moving. If your locks
are not installed before setting the unit in place, make sure
the zip ties are in place to prevent the door from opening
while moving.
2.
PART NO. 1000629
7
Open the lower locker doors by cutting the temporary zip
tie in the lock hasp hole.
Remove the false floor from the locker.
Using a socket wrench, 6" extension, and deep well 9/16"
socket, install the anchor washer and nut.
Install the false floor.
Installation
THIS DOCUMENT IS CONFIDENTIAL AND PROPRIETARY PART NO. 1000629
8
Remove nuts from the (4) studs.
Install the Slope Top.
Open Door or Doors on top units and place slope top on the
aligning holes.
Install locking nuts and secure to cabinet.
3.
Installation
THIS DOCUMENT IS CONFIDENTIAL AND PROPRIETARY
4
PART NO. 1000629
Punch knock outs as shown in Detail A.
Use touch up paint to cover bare metal after knock outs are removed.
Postion the cabinets in place with the doors in the open position.
Ganging Hardware Kit requirred, 1 per pair of units ganged. Part #7001228
Repeat as needed for multiple units.
Ganging multiple units.
9
X4
Tilt the unight to the upright position using the 4 eyelets at the top of the unit with a
forklift and sling/chain. The operator should be a certified forlift operator.
Lift the unit from the shipping pallet and position on the pad.
Secure the unit to the pad, see Step 2.
Gang the unit the the ajoining cabinets, see step 4.
Install the Slope Top, see Step 3.
Installation of the SVP3
Installation
THIS DOCUMENT IS CONFIDENTIAL AND PROPRIETARY
5
PART NO. 1000629
10
6This completes Installation.
Lifting Eyelets
Inhaltsverzeichnis
Andere Champion Tragbarer Generator Handbücher
Champion
Champion 100571 Bedienungsanleitung
Champion
Champion 201271 Bedienungsanleitung
Champion
Champion 42451 Systemhandbuch
Champion
Champion 46514 Handbuch
Champion
Champion 201160 Bedienungsanleitung
Champion
Champion 73540i Systemhandbuch
Champion
Champion 201072 Bedienungsanleitung
Champion
Champion 201184 Bedienungsanleitung
Champion
Champion QUICK START 200990 Bedienungsanleitung
Champion
Champion 201286 Bedienungsanleitung
Champion
Champion 71001I Systemhandbuch
Champion
Champion 46551 Systemhandbuch
Champion
Champion 201079 Bedienungsanleitung
Champion
Champion 41537 Systemhandbuch
Champion
Champion 201161 Bedienungsanleitung
Champion
Champion 100637 Bedienungsanleitung
Champion
Champion 100156 Systemhandbuch
Champion
Champion 201042 Bedienungsanleitung
Champion
Champion 201214 Bedienungsanleitung
Champion
Champion 201169 Bedienungsanleitung
