Chatsworth Products CUBE-IT+ CABINET Bedienungsanleitung

THIS STEP IS OPTIONAL, THE CABINET CAN BE

MOUNTED WITH THE REAR PANEL ATTACHED

STEP 1. DETERMINE WHICH SIDE THE CABINET WILL HINGE FROM. THE

CABINET IS SHOWN WITH THE HINGE ON THE LEFT SIDE, INVERT THE

CABINET IF YOU WANT THE HINGE ON THE RIGHT SIDE.

STEP 2. UNLOCK THE REAR FRAME AND OPEN IT TO GET ACCESS TO

THE HINGE BOLT NUTS.

STEP 3. REMOVE THE CENTER BOLT FROM THE BOTTOM HINGE ONLY.

LOOSEN THE OTHER TWO BOLT NUTS ON THE BOTTOM HINGE. DO

NOT REMOVE OR LOOSEN THE BOLTS ON THE TOP HINGE.

STEP 4. SLIDE THE BOTTOM HINGE PIN UP UNTIL THE LOOSENED

BOLTS REACH THE END OF THE SLOT. REMOVE THE REAR FRAME BY

MOVING THE BOTTOM OF THE FRAME TO THE REAR AND THEN

DOWNWARD TO DISENGAGE IT FROM THE TOP HINGE PLATE.

REMOVING REAR PANEL FROM CABINET

THIS DRAWING CONTAINS INFORMATION PROPRIETARY TO

CHATSWORTH PRODUCTS, INC. ANY REPRODUCTION DISCLOSURE

OR USE OF THIS DRAWING IS EXPRESSLY FORBIDDEN EXCEPT

AS AGREED TO IN WRITING BY CHATSWORTH PRODUCTS, INC.

INSTALLATION

INSTRUCTIONS,

CUBE-IT+ CABINET

IIS-711890, SHEET 1 OF 4 - INSTALLATION INSTRUCTIONS, CUBE IT CABINET - 1:4 - 1-28-03 - ISS. 6 - CPI/BK

DETAIL A

REMOVE CENTER NUT FROM

INSIDE THEN REMOVE BOLT

SLIDE HINGE PIN UP

TO END OF SLOTS

LOOSEN NUTS FROM

INSIDE, DO NOT

REMOVE BOLTS

THIS DRAWING CONTAINS INFORMATION PROPRIETARY TO

CHATSWORTH PRODUCTS, INC. ANY REPRODUCTION DISCLOSURE

OR USE OF THIS DRAWING IS EXPRESSLY FORBIDDEN EXCEPT

AS AGREED TO IN WRITING BY CHATSWORTH PRODUCTS, INC.

INSTALLATION

INSTRUCTIONS,

CUBE-IT+ CABINET

IIS-711890, SHEET 2 OF 4 - ASSEMBLY INSTRUCTIONS, CUBE IT CABINET - 1:4 - 1-28-03 - ISS.6 - CPI/BK

16.00

31.87 FOR 36" HIGH CAB

44.12 FOR 48" HIGH CAB

19.62 FOR 24" HIGH CAB

MOUNTING REAR PANEL TO WALL

STEP 1. INSURE THAT THE WALL OR MOUNTING SURFACE HAS

SUFFICIENT STRENGTH TO SUPPORT THE CABINET AND

THE EXPECTED CABINET PAYLOAD. THE MOUNTING

SURFACE MUST ALSO BE FLAT AND EXTEND BEYOND THE

TOP, BOTTOM, LEFT, AND RIGHT EDGES OF THE REAR PANEL.

STEP 2. DRILL 11/64" PILOT HOLES FOR THE FOUR 1/4-10 X 2" LAG

SCREWS TO THE DIMENSIONS SHOWN ON THE DRAWING OR

USE THE MOUNTING TEMPLATE PROVIDED.

THE SCREWS SHOULD GO DIRECTLY INTO THE WALL STUDS.

STEP 3. INSTALL THE LAG SCREWS INTO THE HOLES. THE SCREW HEAD

SHOULD PROTRUDE ABOUT 3/8" FROM THE WALL.

STEP 4. MOUNT THE REAR FRAME TO THE WALL BY HOOKING

THE KEYHOLES OVER THE SCREWS. TIGHTEN THE

SCREWS SECURELY.

STEP 5. INSTALL THE REMAINING 2 LAG SCREWS IN THE HOLES

BELOW THE TOP TWO KEYHOLES.

MOUNTING KEYHOLES

SCREWS SHOULD

PROTRUDE 3/8"

3/4" PLYWOOD

BACKBOARD

WALL STUDS 16"

ON CENTER

THE REAR FRAME MUST BE SECURED TO WALL USING

ALL 6 LAG SCREWS PROVIDED. THE SCREWS ARE

INTENDED TO GO THROUGH 3/4" PLYWOOD

BACK-BOARD AND THEN INTO WOOD WALL STUDS.

FOR MASONRY SURFACE, THE INSTALLER MUST

PROVIDE APPROPRIATE HARDWARE.

NOTE:

INSTALL 2 LAG SCREWS IN HOLES

BELOW TOP KEYHOLES AFTER THE REAR

FRAME HAS BEEN MOUNTED TO WALL

THIS DRAWING CONTAINS INFORMATION PROPRIETARY TO

CHATSWORTH PRODUCTS, INC. ANY REPRODUCTION DISCLOSURE

OR USE OF THIS DRAWING IS EXPRESSLY FORBIDDEN EXCEPT

AS AGREED TO IN WRITING BY CHATSWORTH PRODUCTS, INC.

INSTALLATION

INSTRUCTIONS,

CUBE-IT+ CABINET

IIS-711890, SHEET 3 OF 4 - ASSEMBLY INSTRUCTIONS, CUBE IT CABINET - 1:4 - 1-28-03 - ISS. 6 - CPI/BK

MOUNTING CABINET TO REAR PANEL

STEP 1. HOOK THE TOP HINGE PLATE ONTO THE TOP HINGE PIN.

STEP 2. ALIGN THE BOTTOM HINGE PLATE HOLE WITH THE BOTTOM

HINGE PIN. SLIDE THE HINGE PIN DOWN INTO THE HINGE HOLE

AS FAR AS POSSIBLE.

STEP 3. REINSTALL THE CENTER BOLT AND NUT. TIGHTEN ALL THREE

BOTTOM NUTS SECURELY.

THE CENTER BOLT MUST BE REPLACED TO

INSURE THAT THE HINGE PIN DOES NOT

SLIP DURING OPERATION

24.00

36.25,

OR 48.50

24.00,

OR 36.00

18.00,

THIS DRAWING CONTAINS INFORMATION PROPRIETARY TO

CHATSWORTH PRODUCTS, INC. ANY REPRODUCTION DISCLOSURE

OR USE OF THIS DRAWING IS EXPRESSLY FORBIDDEN EXCEPT

AS AGREED TO IN WRITING BY CHATSWORTH PRODUCTS, INC.

INSTALLATION

INSTRUCTIONS,

CUBE-IT+ CABINET

IIS-711890, SHEET 4 OF 4 - INSTALLATION INSTRUCTIONS, CUBE IT CABINET - 1:5 - 1-28-03 - ISS. 6 - CPI/BK

RUBBER GROMMETS (FOUR PROVIDED) CAN

BE INSTALLED IN LARGEST KNOCKOUT HOLE.

SLIT GROOVES WITH KNIFE TO ALLOW CABLE

PASS THROUGH

THE DOOR CAN BE HINGED FROM EITHER SIDE OF THE CABINET.

1. REMOVE THE FOUR SCREWS AND NUTS FROM THE HINGES.

2. TURN THE DOOR OVER.

3. REINSTALL THE SCREWS AND NUTS ON THE OPPOSITE SIDE.

1/2" AND 3/4" CONDUIT KNOCKOUTS

THE 1/2" MUST BE PUNCHED OUT FROM THE INSIDE

THE 3/4" MUST BE PUNCHED OUT FROM THE OUTSIDE

2" AND 2 1/2" CONDUIT KNOCKOUTS

THE 2" MUST BE PUNCHED OUT FROM THE INSIDE

THE 2 1/2" MUST BE PUNCHED OUT FROM THE OUTSIDE DETAIL A

USE COMBINATION OF SLOTS

TO GET DESIRED RAIL DEPTH

MOUNTING EQUIPMENT RAIL

MOUNTING RAIL DEPTH CAN BE ADJUSTED BY

REMOVING NUTS AND MOVING THE RAIL TO

THE DESIRED POSITION. USE A COMBINATION

OF ONE OF THE TWO SLOTS ON THE RAIL AND

ONE OF THE SLOTS ON THE SIDE PANELS.

Andere Chatsworth Products Rack & Stand Handbücher

Chatsworth Products

Chatsworth Products TeraFrame F Series Bedienungsanleitung

Chatsworth Products

Chatsworth Products GlobalFrame Gen 2 GT Series Bedienungsanleitung

Chatsworth Products

Chatsworth Products OBERON 3036 Series Bedienungsanleitung

Chatsworth Products

Chatsworth Products GF-3D220-CB Bedienungsanleitung

Chatsworth Products

Chatsworth Products GlobalFrame GF Series Bedienungsanleitung

Chatsworth Products

Chatsworth Products TeraFrame N Gen 3 Series Bedienungsanleitung

Chatsworth Products

Chatsworth Products Cube-iT FILTER KIT Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung