Chauvet SkyScan 4000 Bedienungsanleitung

5200 NW 108th Avenue Sunrise, FL 33351 U.S.A.

(800) 762-1084 – (954) 929-1115

FAX (954) 929-5560

www.chauvetlighting.com

SkyScan™ 4000

USER MANUAL

Snapshot

OK on Dimmer

For Use in Dry

Outdoor Location

For Use in Wet

Outdoor Location

Sound Activated

DMX512

Master/Slave

115V/230V Switch

Replaceable Fuse

Duty Cycle

SkyScan™ 4000 User Manual 2 1/30/2012 4:39 PM

TABLE OF CONTENTS

1. Before You Begin................................................................................................................................ 3

What is included .......................................................................................................................................3

Unpacking Instructions..............................................................................................................................3

AC Power.................................................................................................................................................3

Safety Instructions ....................................................................................................................................4

2. Introduction.........................................................................................................................................5

Features................................................................................................................................................... 5

Product Overview......................................................................................................................................5

3. Setup...................................................................................................................................................6

Lamp........................................................................................................................................................6

Lamp Installation.......................................................................................................................................6

Fuse Replacement....................................................................................................................................8

Mounting ..................................................................................................................................................8

Orientation................................................................................................................................................8

Rigging..................................................................................................................................................... 8

4. Operating Instructions........................................................................................................................ 9

Operation ................................................................................................................................................. 9

To turn the power to the lamp on...............................................................................................................9

To activate the Pan rotation.......................................................................................................................9

Contact Us.............................................................................................................................................. 12

5. Appendix........................................................................................................................................... 13

General Maintenance.............................................................................................................................. 13

Returns Procedure.................................................................................................................................. 13

Claims.................................................................................................................................................... 13

Technical Specifications.......................................................................................................................... 14

SkyScan™ 4000 User Manual 3 1/30/2012 4:39 PM

1. BEFORE YOU BEGIN

What is included

Ø1 x SkyScan™ 4000

Ø1 x Power connector (no cable)

Ø1 x Warranty Card

Ø1 x User Manual

Unpacking Instructions

Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that

all parts are present, and have been received in good condition. Notify the shipper immediately and

retain packing material for inspection if any parts appear damaged from shipping or the carton itself

shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture

must be returned to the factory, it is important that the fixture be returned in the original factory box

and packing.

AC Power 230V ONLY!

To determine the power requirements for a particular fixture, see the label affixed to the back plate of

the fixture or refer to the fixture’s specifications chart. A fixture’s listed current rating is its average

current draw under normal conditions. All fixtures must be powered directly off a switched circuit and

cannot be run off a rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer

channel is used solely for a 0% to 100% switch. Before applying power to a fixture, check that the

source voltage matches the fixture’s requirement. Check the fixture or device carefully to make sure

that if a voltage selection switch exists that it is set to the correct line voltage you will use.

Wiring diagram

The fixture includes an IP-44 wire terminator. This is designed to use the wire configuration shown

below.

Note: this unit does not ship with a wire terminator installed or in the package. You will need to supply

your own power cable and terminator when installing/setting up this fixture. This should only be

done by a qualified technician! You must use the proper cable when connecting this fixture.

Use the minimum recommended cable of 10AWG-3 conductor insulated wiring. This will allow

for proper grounding connection.

Connector Wire

Diagram

SkyScan™ 4000 User Manual 4 1/30/2012 4:39 PM

Safety Instructions

•Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that

they also receive this instruction booklet.

•Always make sure that you are connecting to the proper voltage, and that the line voltage you are

connecting to is not higher than that stated on the decal or rear panel of the fixture.

•This product is intended for dry locations only!

•To prevent risk of fire or shock, do not expose fixture to rain or moisture. Make sure there are no

flammable materials close to the unit while operating.

•The unit must be installed in a location with adequate ventilation, at least 20in (50cm) from adjacent

surfaces. Be sure that no ventilation slots are blocked.

•Always disconnect from power source before servicing or replacing lamp or fuse and be sure to

replace with same lamp source.

•Secure fixture to fastening device using a safety chain. Never carry the fixture solely by its head. Use

its carrying handles.

•Maximum ambient temperature (Ta) is 104°F (40°C). Do not operate fixture at temperatures higher

than this.

•In the event of a serious operating problem, stop using the unit immediately. Never try to repair the

unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please

contact the nearest authorized technical assistance center. Always use the same type spare parts.

•Never connect the device to a dimmer pack.

•Make sure the power cord is never crimped or damaged.

•Never disconnect the power cord by pulling or tugging on the cord.

•Avoid direct eye exposure to the light source while it is on.

Caution! There are no user serviceable parts inside the unit. Do not open the housing or

attempt any repairs yourself. In the unlikely event your unit may require service,

please contact CHAUVET at: 954-929-1115.

Please read these instructions carefully, which includes important

information about the installation, usage and maintenance of this

product.

SkyScan™ 4000 User Manual 5 1/30/2012 4:39 PM

2. INTRODUCTION

Features

•Professional 4000W search light

•Motorized pan: 120° / manual tilt: 40°

•Quad power switches control lamp’s intensity (1k, 2k, 3k, or 4k)

•Silent, hot-restrike ignition

•Variable mechanical zoom

•Ingress Protection: IP33

Product Overview

Access

panel

Tilt Adjustment

knob

Fan intake

vents

Front

lens

Transport,

locking

wheels

Carrying

handle

Power input

connector

SkyScan™ 4000 User Manual 6 1/30/2012 4:39 PM

3. SETUP

Lamp

The lamp for this fixture arrives installed at the factory. Do not touch the envelope (glass area) of the

bulb with bare hands. If this happens, clean the lamp with alcohol and wipe it with a lint free cloth

before installation.

Warning! When replacing the lamp, please wait 15 minutes after powering down to allow the

unit to cool! Always disconnect from main power prior to lamp replacement.

Lamp Installation

Note: the lamp is installed from the back (rear) of the fixture.

1) Be sure to remove power to the fixture before replacing the lamp.

2) Using a Phillips #2 screwdriver, remove the back cover of the fixture. Be careful of the wires for

the fan, as this is attached to the back cover and is easy to damage when removing the panel.

3) Then, remove the front cover with a Phillips #2 screwdriver. Although the lamp is installed

through the back of the fixture, you will need to gain access to the front of the fixture to detach

the front end of the lamp. This is done with a crescent wrench.

4) Remove the lamp by loosening and detaching both ends of the lamp. Then, pull the old lamp out

through the back of the fixture.

5) Then, install the new lamp the same way the old lamp was removed, but in reverse.

6) Close the front & rear cover before connecting power to the fixture.

Note: be careful not to touch the envelope of the lamp! Always use an alcohol wipe to clean

the lamp after installation to remove any residue and oil from the envelope!

Back end of lamp

Front end of lamp

This is the nut to

remove the lamp

This is the nut to

remove the lamp

SkyScan™ 4000 User Manual 7 1/30/2012 4:39 PM

WARNING!

Note: please be sure to adhere to the following instructions and cautions before

installing/servicing this lamp.

Mechanical installation

Because of their high luminance, UV radiation and internal pressure in both the hot and cold state, Xenon

lamps may only be operated in enclosed lamp casings specially constructed for the purpose. Always use the

safety covers supplied when handling Xenon lamps. When handling the lamps without their safety boxes,

always wear safety goggles, a face mask and gauntlets with wrist protectors. Lamps with standard or

Suprasil quartz emit intense UV radiation and produce ozone in the surrounding air.

Certain precautions must therefore be observed when handling these lamps:

• All Xenonlamps are supplied in a safety cover. This protects users from possible spontaneous or induced

bursting of the lamp. You should handle lamps only with safety cover. Store this safety cover for use during

the removal of the lamp at the end of its service life.

You should wear leather gloves covering the arteries and veins of your wrists and protective

goggles or complete face protection covering the arteries and veins of your neck, such as a

transparent plastic mask.

Lamp Storage

Lamps may only be stored if suspended freely from their bases inside their safety covers. Leaving them to

roll around unprotected on a desk or shelf can result in micro cracks in the surface of the quartz glass, and

burst lamps later on.

• If the lamp is inadvertently operated inside its safety cover, the sleeve will melt within a few seconds and

the lamp will be unusable.

• When removing lamps, the reverse procedure must be followed: first put the safety cover or some

protection around the lamp, then remove the lamp.

Electrical connection

Care must be taken to ensure that the lamp is connected with correct polarity; the positive pole of the

rectifier must be connected to the base marked “+”, the negative pole to the base marked “-”. Incorrect

polarity results in total lamp failure within a few seconds.

Cleaning the lamps

Xenon lamps may only be held by the base. If the quartz bulb or the shafts should ever be inadvertently

touched with bare fingers (which should never happen, because unprotected lamps should only be handled

with leather gloves), the fingerprints must be removed immediately. A lint-free cloth moistened with spirit is

best for this, after which the lamp should be rubbed dry, taking care not to scratch the quartz glass surface.

Damage to the quartz may cause the lamp to break during later operation. If fingerprints are not removed

they burn into the quartz glass surface where they act as a seed for ever-expanding recrystallization of the

quartz. This causes the quartz to lose its strength and increases the risk of bursting.

SkyScan™ 4000 User Manual 8 1/30/2012 4:39 PM

FUSE

The fuse is located

inside this

compartment. Remove

using a Phillips #2

screwdriver.

Fuse Replacement

With a Phillips #2 screwdriver, unscrew the fuse holder from its housing. Remove the damaged fuse

from its holder and replace with exact same type fuse. Screw the fuse holder back in its place and

reconnect power.

Note: there are 4 fuses in this fixture, each located by

the corresponding lamp power switches

Mounting

ORIENTATION

This fixture may only be mounted in a standing, vertical position, provided there is adequate room for

ventilation and movement.

Note: this fixture MUST be positioned in an upright position to allow proper cooling,

ventilation, and IP rating!

RIGGING

It is important never to obstruct the fan or vents pathway. Adjust the angle of the fixture by loosening

both knobs and tilting the fixture. After finding the desired position, retighten both knobs.

•When selecting installation location, take into consideration lamp replacement access and routine

maintenance.

•For use in dry locations only!

Disconnect the power cord before replacing a fuse and always

replace with the same type fuse.

SkyScan™ 4000 User Manual 9 1/30/2012 4:39 PM

4. OPERATING INSTRUCTIONS

Operation

TO TURN THE POWER TO THE LAMP ON

1) Using the 4 lamp power switches, select one at a time, in combination, until you reach the

desired light output.

2) Please wait 30 seconds between activating each additional lamp switch.

TO ACTIVATE THE PAN ROTATION

1) Locate the pan motor switch.

2) Switch it to the “ON” position to enable bi-directional rotation.

3) To disable bi-directional rotation, switch this to the “OFF” position.

Note: the pan cannot be manually adjusted.

Pan motor

switch

Fuse (X4)

15A 250V

Lamp power

switch (X4)

Power Indicator

SkyScan™ 4000 User Manual 10 1/30/2012 4:39 PM

TO ADJUST THE ZOOM OF THE FIXTURE

1) Locate the “ZOOM” adjustment of the fixture, highlighted in the diagram below.

2) Turn the adjustment knob clockwise to increase the beam angle.

3) Turn the adjustment knob counter-clockwise to decrease the beam angle.

Zoom adjustment

knob

Inhaltsverzeichnis

Andere Chauvet Scheinwerfer Handbücher

Chauvet

Chauvet EZpar 64 RGBA Bedienungsanleitung

Chauvet

Chauvet Freedom Par Quad-4 IP Bedienungsanleitung

Chauvet

Chauvet COLORdash Accent UV Bedienungsanleitung

Chauvet

Chauvet LEDRain 56C Bedienungsanleitung

Chauvet

Chauvet LFS-5D Bedienungsanleitung

Chauvet

Chauvet Ovation H-105WW Bedienungsanleitung

Chauvet

Chauvet 4 Bar Flex Bedienungsanleitung

Chauvet

Chauvet Rotating Moons CH-208 Bedienungsanleitung

Chauvet

Chauvet PowerStream 4 Bedienungsanleitung

Chauvet

Chauvet Nexus Bedienungsanleitung

Chauvet

Chauvet Laser Wizard CH-505 Bedienungsanleitung

Chauvet

Chauvet Nexus 2x2 Bedienerhandbuch

Chauvet

Chauvet COLORdash Par-Tri 18VW Bedienungsanleitung

Chauvet

Chauvet LED PAR 38-18UVB Bedienungsanleitung

Chauvet

Chauvet COLORdash Batten-Hex 8 Bedienungsanleitung

Chauvet

Chauvet COLORado Batten 72 Tour Bedienungsanleitung

Chauvet

Chauvet 4 Bar Flex Bedienungsanleitung

Chauvet

Chauvet ORB Bedienungsanleitung

Chauvet

Chauvet LEDrain 64 Bedienungsanleitung

Chauvet

Chauvet GigBAR IRC Bedienungsanleitung

Chauvet

Chauvet Cubix 2.0 Bedienungsanleitung

Chauvet

Chauvet Intimidator Barrel LED 300 Bedienungsanleitung

Chauvet

Chauvet Q-WASH 560Z-LED Bedienungsanleitung

Chauvet

Chauvet 4BAR Tri Bedienungsanleitung

Beliebte Scheinwerfer Handbücher anderer Marken

VIZULO

VIZULO Micro Martin Benutzerhandbuch

EuroLite

EuroLite LED IP FL-100 SMD Bedienungsanleitung

Cooper Wheelock

Cooper Wheelock XB12 Bedienungsanleitung

Allen + Roth

Allen + Roth 17624-000 Bedienungsanleitung

ADJ

ADJ 4 STAGE PAK Bedienungsanleitung

Cooper Lighting

Cooper Lighting EGL91SW233 Bedienungsanleitung

Max

Max 37496 Bedienungsanleitung

BEGA

BEGA 85 143 Bedienungsanleitung

Beamz

Beamz 151.226 Bedienungsanleitung

EuroLite

EuroLite LED IP FL-8 Bedienungsanleitung

Ledj

Ledj PERFORMER 36 RGB Bedienungsanleitung

Perel

Perel ELS3 Bedienungsanleitung

Perel

Perel ELS3WD Bedienungsanleitung

LumX

LumX LM 36130 Bedienungsanleitung

Xtricity

Xtricity 4-80053 Bedienungsanleitung

Stahl

Stahl 6521/4 Series Bedienungsanleitung

Ecosense

Ecosense EcoSpec Bedienungsanleitung

Ayrton

Ayrton minipanel FX Bedienungsanleitung