Chauvet LED-BAR Bedienungsanleitung

CHAUVET, 3000 N 29th Ct, Hollywood, FL 33020 U.S.A

(800) 762-1084 –(954) 929-1115

FAX (954) 929-5560

www.chauvetlighting.com

2005-11-22/09:18

LED-BAR

COLORbar™

USER MANUAL

LED-BAR User Manual 2 2005-11-22/09:18

Table of Content

BEFORE YOU BEGIN....................................................................................................................................................... 3

WHAT IS INCLUDED .......................................................................................................................................................................................................... 3

UNPACKING INSTRUCTIONS.............................................................................................................................................................................................. 3

AC POWER ..................................................................................................................................................................................................................... 3

SAFETY INSTRUCTIONS.................................................................................................................................................................................................... 3

INTRODUCTION............................................................................................................................................................... 4

FEATURES....................................................................................................................................................................................................................... 4

DMX CHANNEL SUMMARY ............................................................................................................................................................................................... 4

PRODUCT OVERVIEW....................................................................................................................................................................................................... 5

SETUP .............................................................................................................................................................................. 6

POWER ........................................................................................................................................................................................................................... 6

MOUNTING ...................................................................................................................................................................................................................... 6

OPERATING INSTRUCTIONS.......................................................................................................................................... 7

CONTROL MENU FUNCTIONS ........................................................................................................................................................................................... 7

APPLYING CHANGES TO FUNCTIONS................................................................................................................................................................................. 7

MASTER/SLAVE &STAND ALONE MODES ......................................................................................................................................................................... 7

Program Control Options.................................................................................................................................................................................... 8

Daisy Chain Connection..................................................................................................................................................................................... 8

DMX CONTROL MODE..................................................................................................................................................................................................... 9

Setting the DMX address ................................................................................................................................................................................... 9

APPENDIX...................................................................................................................................................................... 10

DMX PRIMER ................................................................................................................................................................................................................ 10

Fixture Linking .................................................................................................................................................................................................. 10

DMX CHANNEL VALUES ................................................................................................................................................................................................ 11

17 Channel Mode ............................................................................................................................................................................................. 11

5 Channel Mode ............................................................................................................................................................................................... 11

6 Channel Mode (Auto & Sound Active) .......................................................................................................................................................... 12

RETURNS PROCEDURE .................................................................................................................................................................................................. 12

CLAIMS ......................................................................................................................................................................................................................... 12

TECHNICAL SPECIFICATIONS .......................................................................................................................................................................................... 13

TECHNICAL SUPPORT .................................................................................................................................................................................................... 13

LED-BAR User Manual 3 2005-11-22/09:18

AC Voltage Switch Example

BEFORE YOU BEGIN

What is included

1 x LED-BAR COLORbar™

Warranty Card

Users Manual

Unpacking Instructions

Immediately upon receiving a product, carefully unpack the carton, check the contents to ensure that

all parts are present, and have been received in good condition. Notify the shipper immediately and

retain packing material for inspection if any parts appear damaged from shipping or the carton itself

shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture

must be returned to the factory, it is important that the fixture be returned in the original factory box

and packing.

AC Power To determine the power requirements for a particular product, see the label affixed to the back plate

of the product or refer to the product’sspecifications chart. A product’slisted current rating is its

average current draw under normal conditions. All fixtures must be powered directly off a switched

circuit and cannot be run off a rheostat (variable resistor) or dimmer circuit,

even if the rheostat or dimmer channel is used solely for a 0% to 100%

switch. Before applying power, check that the source voltage matches the

product’srequirement. Check the product or device carefully to make sure

that if a voltage selection switch exists that it is set to the correct line

voltage you will use.

Warning! If applicable, verify that the power select switch on your unit matches the line

voltage applied. All fixtures must be connected to circuits with a suitable Earth

Ground.

Safety Instructions

Please keep this User Guide for future consultation. If you

sell the unit to another user, be sure that they also receive

this instruction booklet.

Always make sure that you are connecting to the proper

voltage and that the line voltage you are connecting to is

not higher than that stated on decal or rear panel of the

fixture.

This product is intended for indoor use only!

To prevent risk of fire or shock, do not expose fixture to

rain or moisture. Make sure there are no flammable

materials close to the unit while operating.

The unit must be installed in a location with adequate

ventilation, at least 50cm from adjacent surfaces. Be sure

that no ventilation slots are blocked.

Always disconnect from power source before servicing or

replacing lamp or fuse and be sure to replace with same

lamp source.

Secure fixture to fastening device using a safety chain.

Never carry the fixture solely by its head. Use its carrying

handles.

Maximum ambient temperature is Ta: 40°. Do not operate

fixture at temperatures higher than this.

In the event of serious operating problem, stop using the

unit immediately. Never try to repair the unit by yourself.

Repairs carried out by unskilled people can lead to

damage or malfunction. Please contact the nearest

authorized technical assistance center. Always use the

same type spare parts.

Don’t connect the device to a dimmer pack.

Make sure power cord is never crimped or damaged.

Never disconnect power cord by pulling or tugging on the

cord.

Avoid direct eye exposure to lamp while it is on.

Caution! There are no user serviceable parts inside the unit. Do not open the housing or

attempt any repairs yourself. In the unlikely event your unit may require service,

please contact CHAUVET.

Please read these instructions carefully, which includes important

information about the installation, usage and maintenance?

LED-BAR User Manual 4 2005-11-22/09:18

CHDESCRIPTION

1 Control Configurations

2 Red

3 Green

4 Blue

5 Dimmer

Section 1

6 Red

7 Green

8 Blue

9 Dimmer

Section 2

10 Red

11 Green

12 Blue

13 Dimmer

Section 3

14 Red

15 Green

16 Blue

17 Dimmer

Section 4

CHDESCRIPTION

1 Control Configurations

2 All Red

3 All Green

4 All Blue

5 All Dimmer

17 Channel Configuration

RGB Mix 5 Channel Configuration

RGB Mix

CHDESCRIPTION

1 Control Configurations

2 Patterns

3 Color 1

4 Color 2

5 Speed

6 Fade

6 Channel Configuration

Auto Run & Sound Active

INTRODUCTION

Features

CONTROL FEATURES

5-17 channel DMX-512 LED panel system

Operating modes

- 17 channel mode: 4 sections of RGB mix control

- 5 channel mode: RGB mix control of all sections

- 6 channel mode: Automatic - Adjust or change; program, color, speed and fade

- 6 channel mode: Sound Active - Adjust or change; program, color, speed and fade

FEATURES

96 LEDs total in 4 panels, 24 LEDs per panel surface

- Red (32), Green (32) and Blue (32)

Ultra bright LEDs

RGB color mixing

Built in color change programs

Low power consumption

Up to 100,000-hour LED life span

Master/Slave mode

DMX Channel Summary

Introduction

LED-BAR User Manual 5 2005-11-22/09:18

Control Panel

DMX Input

Fuse

Switch selectable

AC Voltage

Hanging yoke

Sound sensitivity knob

Power Switch

IEC Plug for AC Input

DMX Output

IEC AC Output

Product Overview

Introduction

LED-BAR User Manual 6 2005-11-22/09:18

Slide switch up or down

depending on your line voltage.

Hanging Clamp

SETUP

Power Your product is equipped with switch-selectable AC power setting.

Warning! Verify that the power select switch on your unit

matches the line voltage applied. All fixtures must

be connected to circuits with a suitable Earth

Ground.

To determine the power requirements for a particular fixture, see the label affixed to the back plate

of the fixture or refer to the fixture’s specifications chart.

A fixture’s listed current rating is its average current draw under normal conditions.

All fixtures must be powered directly off a switched circuit and cannot be run off a rheostat

(variable resistor) or dimmer circuit, even if the rheostat or dimmer channel is used solely for a 0%

to 100% switch.

Before applying power to a fixture, check that the source voltage matches the fixture’s

requirement.

All fixtures must be connected to circuits with a suitable Earth Ground.

Power Cable Configuration

CABLE PIN INTERNATIONAL

BROWN Live L

BLUE Neutral N

YELLOW/GREEN Earth EG (Ground)

Mounting

Orientation

This fixture can be mounted on a truss using a clamp in any position.

Rigging

The fixture includes a mounting yoke to which 1 rigging clamp can be

bolted.

1. Align the clamp screw with the center hole on the yoke and tighten.

2. Verify the structure can hold 10 times the weight of all to-be installed fixtures.

3. Adjust the angle on the yoke arm as necessary.

LED-BAR User Manual 7 2005-11-22/09:18

DOWN UP MEN

POWER

OPERATING INSTRUCTIONS

The COLORbar™is a DMX-512 controllable, full RGB color mix multi-panel led fixture made up of

highly efficient and super bright leds. There are four led panels whose intensity can be controlled

either individually or together allowing the creation of an unlimited range of colors.

The COLORbar™can operate in Stand-Alone, Master/Slave and via DMX-512 control utilizing

between 5 and 17 channels.

Control Menu Functions

FUNCTION DESCRIPTION

CHA DMX channel addressing

PAT Programs # 0 ~ 9, program 0 is a multi-color chase program

1 ~ 9 are 2-color chases and allows user selection of CO1 and CO2 colors

CO1 Color Selection: Range 0 ~ 7, refer to Color Table, applies to PAT: 1-9

CO2 Color Selection: Range 0 ~ 7, refer to Color Table, applies to PAT: 1-9

SPE Speed of chase: 1 ~ 127

S-C Sound Active: ON = Sound, OFF = Auto

SS Cross Fade: ON = Fade, OFF = No Fade

SLA ON = Slave, OFF = Master ( ON is necessary for DMX control)

Color Tables

NO. 0 1 2 3 4 5 6 7

Color Blackout Red Green Blue Yellow Magenta Cyan White

Applying changes to Functions

1. Press the [MENU] button repeatedly until the display

reads the menu function you wish to change.

2. Press the [DOWN] or [UP] buttons to toggle or scroll

through values that pertain to that function.

Master/Slave & Stand Alone Modes

The Master/Slave mode will allow you to link up to as many units you want in a daisy chain fashion. In

this mode, the first unit in the daisy chain will automatically command all other units following.

1. Connect all COLORbar™units in a daisy chain configuration as described in the section following.

2. Master Unit:

a. Press the [MENU] button until the display reads [].

b. Use the [UP] or [DOWN] buttons to set the display to [] for Master mode.

3. Slaves:

a. Press the [MENU] button until the display reads [].

b. Use the [UP] or [DOWN] buttons to set the display to [] for Slave mode.

(this should be the default setting)

4. You can also run the fixtures in an automatic stand-alone mode by simply setting all fixtures to run

as master units.

Appendix

LED-BAR User Manual 8 2005-11-22/09:18

220 110V

220V

FUSE: 1A

POWER

OFF

DOW N UP MENU

PO WE R SOUN D

SENSI T IVITY

POWEROUTPUT

DMXOUTPUT

POWERINPUT DMXINPUT

COLOR bar TM

220

110V

220V

FUSE: 1APOWER

OFF

DOWN U P M EN U

POWE R SOUN D

SENSI T IVI T Y

POWEROUTPUT

DMXOUTPUT

POWERINPUT DMXINPUT

COLOR bar

220 110V

220V

FUSE: 1A

POWER

OFF

DOW N UP MENU

PO WE R SOUN D

SENSI T IVITY

POWEROUTPUT

DMXOUTPUT

POWERINPUT DMXINPUT

COLOR bar TM

Optional DMX Controller

DMX cable

Daisy Chain Power Connector

Chauvet Model # EXT-Z

Program Control Options

In Master or Stand Alone modes several variables can be changed using the control panel to affect

changes to the internal programs. You can choose from 10 preset program patterns. Pattern 0 is a

fully automatic multi-colored chase program. The remaining patterns 1 ~ 9 are 2-color chases and the

user can select alternating colors from the list of colors available in the Color Table. The speed of the

running programs can be adjusted for all patterns unless in Sound Active mode. A cross fade function

allows the gradual shifting of one color to the next during a program with color chase.

Daisy Chain Connection

1. Connect the (male) 3 pin connector side of the DMX cable to the output (female) 3 pin connector

of the first fixture.

2. Connect the end of the cable coming from the first fixture which will have a (female) 3 pin

connector to the input connector of the next fixture consisting of a (male) 3 pin connector. Then,

proceed to connect from the output as stated above to the input of the following fixture and so on.

Appendix

LED-BAR User Manual 9 2005-11-22/09:18

DMX Control Mode

Operating in a DMX Control mode environment gives the user the greatest flexibility when it comes to

customizing or creating a show. In this mode you will be able to control each individual trait of the

fixture and each fixture independently.

1. Enable DMX control by setting SLA to ON in the control panel.

2. Address each fixture accordingly using the CHA function.

Setting the DMX address

This DMX mode enables the use of a universal DMX controller device. Each fixture requires a "start

address" from 1 to 511. A fixture requiring one or more channels for control begins to read the data

on the channel indicated by the start address. For example, a fixture that occupies or uses 7 channels

of DMX and was addressed to start on DMX channel 100, would read data from channels: 100, 101,

102, 103, 104, 105 and 106. Choose start addresses so that the channels used do not overlap and

notate the start address selected for future reference.

If this is your first time addressing a fixture using the DMX-512 control protocol than I suggest jumping

to the Appendix Section and read the heading “DMX Primer”. It contains very useful information that

will help you understand its use.

1. Press the [MENU] button on the control panel until the display reads [].

2. Use the [UP] and [DOWN] buttons to increase or decrease channel values until the desired value

is displayed.

3. Remember to set function [] to ON in order to enable DMX control.

LED-BAR User Manual 10 2005-11-22/09:18

APPENDIX

DMX Primer

There are 512 channels in a DMX-512 connection. Channels may be assigned in any manner. A

fixture capable of receiving DMX-512 will require one or a number of sequential channels. The user

must assign a starting address on the fixture that indicates the first channel reserved in the controller.

There are many different types of DMX controllable fixtures and they all may vary in the total number

of channels required. Choosing a start address should be planned in advance. Channels should

never overlap. If they do, this will result in erratic operation of the fixtures whose starting address is

set incorrectly. You can however, control multiple fixtures of the same type using the same starting

address as long as the intended result is that of unison movement or operation. In other words, the

fixtures will be slaved together and all respond exactly the same.

DMX fixtures are designed to receive data through a serial Daisy Chain. A Daisy Chain connection is

where the DATA OUT of one fixture connects to the DATA IN of the next fixture. The order in which

the fixtures are connected is not important and has no effect on how a controller communicates to

each fixture. Use an order that provides for the easiest and most direct cabling. Connect fixtures

using shielded two conductor twisted pair cable with three pin XLR male to female connectors. The

shield connection is pin 1, while pin 2 is Data Negative (S-) and pin 3 is Data positive (S+). CHAUVET

carries 3-pin XLR DMX compliant cables, DMX-10 (33’), DMX-4.5 (15’) and DMX-1.5 (5’)

Fixture Linking

Note! If you use a controller with a 5 pin DMX output connector, you will need to use a 5

pin to 3 pin adapter. CHAUVET Model No: DMX5M.

The chart below details a proper cable conversion:

3PIN TO 5PIN CONVERSION CHART

Conductor 3 Pin Female (output) 5 Pin Male (Input)

Ground/Shield Pin 1 Pin 1

Data ( - )signal Pin 2 Pin 2

Data ( + ) signal Pin 3 Pin 3

Do not use Do not use

COMMON

DMX +

DMX

INPUT

OUTPUT

Resistance 120

ohm 1/4w between

pin 2 (DMX -) and

pin 3 (DMX +) of

the last fixture.

Termination reduces signal errors and to

avoid signal transmission problems and

interference, it is always advisable to

connect a DMX signal terminator.

DMX connector configuration

Andere Handbücher für LED-BAR

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Chauvet Leuchte Handbücher

Chauvet

Chauvet Q-Spot 250 Bedienungsanleitung

Chauvet

Chauvet Legend 1200E Wash Bedienungsanleitung

Chauvet

Chauvet Vue II Handbuch

Chauvet

Chauvet Batten 80i Bedienungsanleitung

Chauvet

Chauvet F-40 Bedienungsanleitung

Chauvet

Chauvet Legend 1200E Wash Bedienungsanleitung

Chauvet

Chauvet Vue II Bedienungsanleitung

Chauvet

Chauvet Intimidator Wash Zoom 350 IRC Bedienungsanleitung

Chauvet

Chauvet Q-RollTM 250 Bedienungsanleitung

Chauvet

Chauvet CH-BOB Jr. Bedienungsanleitung

Chauvet

Chauvet Elan Bedienungsanleitung

Chauvet

Chauvet LX 5 Bedienungsanleitung

Chauvet

Chauvet DMX-1655R Produkthandbuch

Chauvet

Chauvet Q-Spot 300 Bedienungsanleitung

Chauvet

Chauvet LED-PANEL4 Bedienungsanleitung

Chauvet

Chauvet COLORado Zoom TOUR Bedienungsanleitung

Chauvet

Chauvet LG-20 Bedienungsanleitung

Chauvet

Chauvet PK PAR64C Bedienungsanleitung

Chauvet

Chauvet Scorpion Scan LG-60 Bedienungsanleitung

Chauvet

Chauvet Q-Spot Bedienungsanleitung

Chauvet

Chauvet J-Five Bedienungsanleitung

Chauvet

Chauvet Q-Wash 419Z-LED Bedienungsanleitung

Chauvet

Chauvet Intimidator Wash LED 150 Bedienungsanleitung

Chauvet

Chauvet LED-PANEL4 Bedienungsanleitung

Beliebte Leuchte Handbücher anderer Marken

Emos

Emos CLASSIC ZY1431T Bedienungsanleitung

Westinghouse

Westinghouse Outdoor Lighting Fixture Bedienungsanleitung

Hedler

Hedler C 12 silent Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Puck: CSI Bedienungsanleitung

Energetic Lighting

Energetic Lighting ELYSL-5004 Series Bedienungsanleitung

Lightmaxx

Lightmaxx Shaft 5R Bedienungsanleitung

Triarch

Triarch 31083 Bedienungsanleitung

Philips

Philips 32614 Series Bedienungsanleitung

IKEA

IKEA TIVED Bedienungsanleitung

Lightolier

Lightolier LP200 Bedienungsanleitung

Chauvet Professional

Chauvet Professional ROGUE R1 BEAM WASH Bedienungsanleitung

Martin

Martin MAC 250 Krypton Bedienungsanleitung

Cooper Lighting

Cooper Lighting Halo L3232E Bedienungsanleitung

Stageline

Stageline ODW-2410RGBW Bedienungsanleitung

Light Sky

Light Sky Tornado Series Bedienungsanleitung

Lightolier

Lightolier Paralyte 2424 PLA2G9LS26U Bedienungsanleitung

Lightolier

Lightolier Lytespan 83ED17S Bedienungsanleitung

Lightolier

Lightolier Calculite CS8226 Bedienungsanleitung